Home › Engine / Hybrid System › 2AR-FE (ENGINE CONTROL) › SFI SYSTEM › 2017.09–2021.02
RM33A0E _51 Engine / Hybrid System _065323 2AR-FE ENGINE CONTROL _0329559 SFI SYSTEM C

2AR-FE ENGINE CONTROL  SFI SYSTEM  P0300  Random / Multiple Cylinder Misfire Detected  P0301  Cylinder 1 Misfire Detected  P0302  Cylinder 2 Misfire Detected  P0303  Cylinder 3 Misfire Detected  P0304  Cylinder 4 Misfire Detected  


DESCRIPTION

When the engine misfires, high concentrations of hydrocarbons (HC) enter the exhaust gas. Extremely high hydrocarbon concentration levels can cause an increase in exhaust emission levels. Extremely high concentrations of hydrocarbons can also cause increases in the three-way catalytic converter temperature, which may cause damage to the three-way catalytic converter. To prevent this increase in emissions and to limit the possibility of thermal damage, the ECM monitors the misfire count. When the temperature of the three-way catalytic converter reaches the point of thermal degradation, the ECM blinks the MIL. To monitor misfires, the ECM uses both the camshaft position sensor and the crankshaft position sensor. The camshaft position sensor is used to identify any misfiring cylinders and the crankshaft position sensor is used to measure variations in the crankshaft rotation speed. Misfires are counted when the crankshaft rotation speed variations exceed predetermined thresholds. If the misfire count exceeds the threshold levels, and could cause emission control system performance deterioration, the ECM illuminates the MIL and stores a DTC.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P0300 Random / Multiple Cylinder Misfire Detected Simultaneous misfiring of several cylinders occurs and either of the following conditions is met (2 trip detection logic):
·

A misfire occurs that may damage the three-way catalytic converter (MIL blinks immediately when detected).

·

An emission deterioration misfire occurs (MIL illuminates).


·

Open or short in engine wire harness

·

Connector connection

·

Vacuum hose connections

·

Ignition system

·

Fuel injector assembly

·

Fuel pressure

·

Mass air flow meter sub-assembly

·

Engine coolant temperature sensor

·

Compression pressure

·

Valve timing

·

PCV valve and hose

·

PCV hose connections

·

Intake system

·

Intake air control valve actuator (for tumble control valve)

·

ECM


Comes on/Blinks* (Euro-OBD) / - (Except Euro-OBD)
*: The MIL flashes when a catalyst-damaging misfire is detected.
DTC stored (Euro-OBD) / - (Except Euro-OBD)
P0301 Cylinder 1 Misfire Detected Misfiring of the No. 1 cylinder occurs and either of the following conditions is met (2 trip detection logic):
·

A misfire occurs that may damage the three-way catalytic converter (MIL blinks immediately when detected).

·

An emission deterioration misfire occurs (MIL illuminates).


·

Open or short in engine wire harness

·

Connector connection

·

Vacuum hose connections

·

Ignition system

·

Fuel injector assembly

·

Fuel pressure

·

Mass air flow meter sub-assembly

·

Engine coolant temperature sensor

·

Compression pressure

·

Valve timing

·

PCV valve and hose

·

PCV hose connections

·

Intake system

·

Intake air control valve actuator (for tumble control valve)

·

ECM


Comes on/Blinks* (Euro-OBD) / - (Except Euro-OBD)
*: The MIL flashes when a catalyst-damaging misfire is detected.
DTC stored (Euro-OBD) / - (Except Euro-OBD)
P0302 Cylinder 2 Misfire Detected Misfiring of the No. 2 cylinder occurs and either of the following conditions is met (2 trip detection logic):
·

A misfire occurs that may damage the three-way catalytic converter (MIL blinks immediately when detected).

·

An emission deterioration misfire occurs (MIL illuminates).


·

Open or short in engine wire harness

·

Connector connection

·

Vacuum hose connections

·

Ignition system

·

Fuel injector assembly

·

Fuel pressure

·

Mass air flow meter sub-assembly

·

Engine coolant temperature sensor

·

Compression pressure

·

Valve timing

·

PCV valve and hose

·

PCV hose connections

·

Intake system

·

Intake air control valve actuator (for tumble control valve)

·

ECM


Comes on/Blinks* (Euro-OBD) / - (Except Euro-OBD)
*: The MIL flashes when a catalyst-damaging misfire is detected.
DTC stored (Euro-OBD) / - (Except Euro-OBD)
P0303 Cylinder 3 Misfire Detected Misfiring of the No. 3 cylinder occurs and either of the following conditions is met (2 trip detection logic):
·

A misfire occurs that may damage the three-way catalytic converter (MIL blinks immediately when detected).

·

An emission deterioration misfire occurs (MIL illuminates).


·

Open or short in engine wire harness

·

Connector connection

·

Vacuum hose connections

·

Ignition system

·

Fuel injector assembly

·

Fuel pressure

·

Mass air flow meter sub-assembly

·

Engine coolant temperature sensor

·

Compression pressure

·

Valve timing

·

PCV valve and hose

·

PCV hose connections

·

Intake system

·

Intake air control valve actuator (for tumble control valve)

·

ECM


Comes on/Blinks* (Euro-OBD) / - (Except Euro-OBD)
*: The MIL flashes when a catalyst-damaging misfire is detected.
DTC stored (Euro-OBD) / - (Except Euro-OBD)
P0304 Cylinder 4 Misfire Detected Misfiring of the No. 4 cylinder occurs and either of the following conditions is met (2 trip detection logic):
·

A misfire occurs that may damage the three-way catalytic converter (MIL blinks immediately when detected).

·

An emission deterioration misfire occurs (MIL illuminates).


·

Open or short in engine wire harness

·

Connector connection

·

Vacuum hose connections

·

Ignition system

·

Fuel injector assembly

·

Fuel pressure

·

Mass air flow meter sub-assembly

·

Engine coolant temperature sensor

·

Compression pressure

·

Valve timing

·

PCV valve and hose

·

PCV hose connections

·

Intake system

·

Intake air control valve actuator (for tumble control valve)

·

ECM


Comes on/Blinks* (Euro-OBD) / - (Except Euro-OBD)
*: The MIL flashes when a catalyst-damaging misfire is detected.
DTC stored (Euro-OBD) / - (Except Euro-OBD)

When DTCs for misfiring cylinders are randomly stored, but DTC P0300 is not stored, it indicates that misfires have been detected in different cylinders at different times. DTC P0300 is only stored when several misfiring cylinders are detected at the same time.

MONITOR DESCRIPTION

The ECM illuminates the MIL and stores a DTC when either one of the following conditions, which could cause emission deterioration, is detected (2 trip detection logic).

·

Within the first 1000 crankshaft revolutions after the engine starts, an excessive number of misfires (approximately 40 to 100 misfires per 1000 crankshaft revolutions) occurs once.

·

An excessive number of misfires (approximately 40 to 100 misfires per 1000 crankshaft revolutions) occurs a total of 4 times.


The ECM flashes the MIL (immediately detection logic) and stores a DTC (2 trip detection logic) when either one of the following conditions, which could cause damage to the three-way catalytic converter, is detected.

·

At a high engine speed, a sufficient amount of misfires to damage the catalyst occurring within 200 crankshaft revolutions is detected once.

·

At a normal engine speed, a sufficient amount of misfires to damage the catalyst occurring within 200 crankshaft revolutions is detected 3 times.


MONITOR STRATEGY

Required Sensors/Components (Main) Crankshaft position sensor
Camshaft position sensor
Required Sensors/Components (Related) Engine coolant temperature
Intake air temperature sensor
Mass air flow meter sub-assembly
Frequency of Operation Continuous

TYPICAL ENABLING CONDITIONS

Misfire
Intake air temperature Higher than -10°C (14°F)
Either of the following conditions is met (a) or (b)
(a) Engine coolant temperature at engine start Higher than -7°C (19°F)
(b) Engine coolant temperature Higher than 20°C (68°F)

Monitor Period of Emission-related Misfire
Monitor period Crankshaft 1000 revolutions x 4

Monitor Period of Catalyst-damaging Misfire (MIL Blinks)
Monitor period Crankshaft 200 revolutions x 3

TYPICAL MALFUNCTION THRESHOLDS

Monitor Period of Emission-related Misfire
Misfire rate 0.99% or higher

Monitor Period of Catalyst-damaging Misfire (MIL Blinks)
Number of misfires per 200 revolutions 124 or more (varies with engine speed and engine load)

CONFIRMATION DRIVING PATTERN

1.

Connect the GTS to the DLC3.

2.

Turn the ignition switch to ON.

3.

Turn the GTS on.

4.

Record the DTC(s) and Freeze Frame Data.

5.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

6.

Using GTS, switch the ECM from normal mode to check mode.

Click hereEngine / Hybrid System>2AR-FE (ENGINE CONTROL)>SFI SYSTEM>CHECK MODE PROCEDURE

7.

Start the engine.

8.

Read the misfire count of each cylinder (Cylinder #1 Misfire Count to Cylinder #4 Misfire Count) with the engine idling. If any misfire count is displayed, skip the following confirmation driving pattern.

9.

Drive the vehicle so that the vehicle conditions displayed in Misfire RPM and Misfire Load of the Data List are the same as the freeze frame data. Perform this step several times.

HINT:
·

In order to store misfire DTCs, it is necessary to operate the vehicle for the period of time shown in the table below, using the Misfire RPM and Misfire Load in the Data List.


Engine Speed (rpm) Duration
Idling 8.0 minutes or more
1000 4.5 minutes or more
2000 2.5 minutes or more
3000 1.5 minutes or more


10.

Check whether misfires have occurred by checking for DTCs and Freeze Frame Data.

HINT:

Do not turn the ignition switch off until the stored DTC(s) and Freeze Frame Data have been recorded. When the ECM returns to normal mode (default), the stored DTC(s), Freeze Frame Data and other data will be cleared.


11.

Record the DTC(s), Freeze Frame Data and misfire counts.

12.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

13.

Turn the ignition switch off and wait for at least 30 seconds.


WIRING DIAGRAM

Refer to DTC P0102 for the mass air flow meter sub-assembly circuit.

Click hereEngine / Hybrid System>2AR-FE (ENGINE CONTROL)>SFI SYSTEM>P0102

Refer to Fuel Injector Circuit.

Click hereEngine / Hybrid System>2AR-FE (ENGINE CONTROL)>SFI SYSTEM>Fuel Injector Circuit

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following procedure.


HINT:
·

Check the "Fuel Cut Elps Time" in the Data List or the Freeze Frame Data.

If the elapsed time is over 0 seconds, then the engine speed is high (engine speed at which fuel cut occurs + 500 rpm).

When this has happened, there is the possibility that the No. 1 valve rocker arm sub-assembly will become loose and a fire could start, so check that the No. 1 valve rocker arm sub-assembly is properly attached.

Click hereEngine / Hybrid System>2AR-FE (ENGINE MECHANICAL)>ENGINE UNIT>COMPONENTS

·

By clearing the DTC, "Fuel Cut Elps Time" will be cleared.

·

Referring to the following contents of the Freeze Frame Data (or the pending Freeze Frame Data) enables an estimation of which cylinder has misfired and to what degree.

-

Cylinder #1 Misfire Count to Cylinder #4 Misfire Count: Misfire count according to cylinder.

-

Cat OT MF F/C Cylinder #1 to Cat OT MF F/C Cylinder #4: This expresses a high-frequency misfire was concentrated in a certain cylinder and that cylinder's fuel injection was stopped.


·

If any DTCs other than misfire DTCs are output, troubleshoot those DTCs first.

·

If the misfire does not recur when the vehicle is brought to the workshop, reproduce the conditions stored in the ECM as Freeze Frame Data.

·

If the misfire still cannot be reproduced even though the conditions stored in the ECM as Freeze Frame Data have been reproduced, one of the following factors can be considered to be a possible cause of the problem:

(a)

There was insufficient fuel in the tank.

(b)

Improper fuel was used.

(c)

The spark plugs have been contaminated.

(d)

The problem requires further diagnosis.


·

After finishing repairs, check the misfire counts of the cylinders (Cylinder #1 Misfire Count to Cylinder #4 Misfire Count).

·

Be sure to confirm that no misfiring cylinder DTCs are stored again by conducting the confirmation driving pattern after finishing repairs.

·

When one of Short FT B1S1 or Long FT B1S1 in the Freeze Frame Data is outside the range of +/-15%, the air fuel ratio may be rich (-15% or less) or lean (15% or higher).

·

When Coolant Temp in the Freeze Frame Data is less than 75°C (167°F), the misfires have occurred only while warming up the engine.

·

An extremely imbalanced drive wheel which causes body vibration may cause misfire DTCs to be stored.

·

Read freeze frame data using the GTS. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.



PROCEDURE

1.CHECK ANY OTHER DTCS OUTPUT (IN ADDITION TO MISFIRE DTCS)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.


e.

Read the DTCs.

Powertrain > Engine and ECT > Trouble Codes
50001 234
Result:
Result Proceed to
DTC P0300, P0301, P0302, P0303 and/or P0304 are output A
DTC P0300, P0301, P0302, P0303 and/or P0304 and other DTCs are output B


HINT:

If any DTCs other than P0300, P0301, P0302, P0303 and/or P0304 are output, troubleshoot those DTCs first.




A

2.CHECK PCV HOSE CONNECTIONS

B

2.CHECK PCV HOSE CONNECTIONS
a.

Check the PCV hose connections.

Click hereEngine / Hybrid System>2AR-FE EMISSION CONTROL>PCV VALVE>COMPONENTS

OK:

PCV valve and hose are correctly connected and are not damaged.



Result:
Proceed to
OK
NG



OK

3.READ VALUE USING GTS (MISFIRE RPM AND MISFIRE LOAD)

NG

REPAIR OR REPLACE PCV HOSE

3.READ VALUE USING GTS (MISFIRE RPM AND MISFIRE LOAD)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine and ECT / Data List / All Data / Misfire RPM and Misfire Load.

Powertrain > Engine and ECT > Data List
Tester Display
Misfire RPM
Misfire Load
50003 234 319,320

e.

Read and note the Misfire RPM and Misfire Load values.

HINT:

The Misfire RPM and Misfire Load values indicate the vehicle conditions under which the misfire occurred.



Result:
Proceed to
NEXT



NEXT

4.READ VALUE USING GTS (CYLINDER MISFIRE COUNT)
4.READ VALUE USING GTS (CYLINDER MISFIRE COUNT)
a.

Enter the following menus: Powertrain / Engine and ECT / Data List / All Data / Cylinder #1 Misfire Count, Cylinder #2 Misfire Count, Cylinder #3 Misfire Count and Cylinder #4 Misfire Count.

Powertrain > Engine and ECT > Data List
Tester Display
Cylinder #1 Misfire Count
Cylinder #2 Misfire Count
Cylinder #3 Misfire Count
Cylinder #4 Misfire Count
50003 234 321,322,323,324

b.

Start the engine and allow the engine to idle.


c.

Read each value for Cylinder #1 Misfire Count to Cylinder #4 Misfire Count displayed on the GTS. If no misfire counts occur in any cylinders, perform procedure [A] and [B] and then check the misfire counts again.

i.

Drive the vehicle with the Misfire RPM and Misfire Load noted in the "Read Value Using GTS (Misfire RPM and Misfire Load)" procedures above [A].


ii.

Read the Cylinder #1 Misfire Count to Cylinder #4 Misfire Count or DTCs displayed on the GTS [B].



Result:
Result Proceed to
Most misfires occur in only 1 or 2 cylinders A
3 cylinders or more have equal misfire counts B


HINT:
·

If it is difficult to reproduce misfires for each cylinder, check the Data List item called Misfire Margin. Try to find vehicle driving conditions that lower the Misfire Margin value. Values above 30% are considered normal.

·

If the freeze frame data record of the engine coolant temperature is below 75°C (167°F), the misfire may be detected only when the engine is cold.

·

If the freeze frame data record of the Engine Run Time is below 120 seconds, the misfire may be detected immediately after the engine is started.




A

5.INSPECT SPARK PLUG

B

17.CHECK INTAKE SYSTEM
5.INSPECT SPARK PLUG
a.

Inspect the spark plug of the misfiring cylinder.

Click hereEngine / Hybrid System>2AR-FE (ENGINE CONTROL)>IGNITION SYSTEM>ON-VEHICLE INSPECTION

HINT:

Perform "Inspection After Repair" after replacing the spark plug.

Click hereEngine / Hybrid System>2AR-FE (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION



Result:
Proceed to
OK
NG



OK

6.CHECK FOR SPARKS (SPARK TEST)

NG

6.CHECK FOR SPARKS (SPARK TEST)
a.

Perform a spark test.

Click hereEngine / Hybrid System>2AR-FE (ENGINE CONTROL)>IGNITION SYSTEM>ON-VEHICLE INSPECTION

HINT:
·

If the result of the spark test is normal, proceed to the next step.

·

Perform "Inspection After Repair" after repairing or replacing the ignition system.

Click hereEngine / Hybrid System>2AR-FE (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION




Result:
Proceed to
NEXT



NEXT

7.CHECK CYLINDER COMPRESSION PRESSURE
7.CHECK CYLINDER COMPRESSION PRESSURE
a.

Measure the cylinder compression pressure of the misfiring cylinder.

Click hereEngine / Hybrid System>2AR-FE (ENGINE MECHANICAL)>ENGINE>ON-VEHICLE INSPECTION

HINT:

Perform "Inspection After Repair" after repairing or replacing the engine assembly.

Click hereEngine / Hybrid System>2AR-FE (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION



Result:
Proceed to
OK
NG



OK

8.CHECK TERMINAL VOLTAGE (#10, #20, #30 AND/OR #40)

NG

CHECK ENGINE TO DETERMINE CAUSE OF LOW COMPRESSION

8.CHECK TERMINAL VOLTAGE (#10, #20, #30 AND/OR #40)
A413245C02
1.333,0.292 1.75,0.563 0.417,0.271 0.792,1.74 1.563,1.031 true 2.875,1.802 2.333,1.115 true 1.24,1.813 1.625,1.052 true 1.875,1.781 1.698,1.042 true 2.292,1.781 1.792,1.042 true 1.406,0.323 1.865,0.521 0.458,0.198 10 false C58 0.146,0.052 0.458,0.25 0.313,0.198 10 false *a 0.615,1.781 1.073,1.979 0.458,0.198 10 false #20 1.073,1.833 1.531,2.031 0.458,0.198 10 false #30 1.74,1.813 2.198,2.01 0.458,0.198 10 false #40 2.188,1.813 2.646,2.01 0.458,0.198 10 false #10 2.771,1.854 3.229,2.052 0.458,0.198 10 false E01
*a Front view of wire harness connector
(to ECM)


a.

Disconnect the ECM connector.


b.

Turn the ignition switch to ON.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
C58-21 (#10) - C58-57 (E01) Ignition switch ON 11 to 14 V
C58-18 (#20) - C58-57 (E01) Ignition switch ON 11 to 14 V
C58-19 (#30) - C58-57 (E01) Ignition switch ON 11 to 14 V
C58-20 (#40) - C58-57 (E01) Ignition switch ON 11 to 14 V



Result:
Proceed to
OK
NG



OK

9.CHECK FUEL INJECTOR ASSEMBLY OF MISFIRING CYLINDER

NG

9.CHECK FUEL INJECTOR ASSEMBLY OF MISFIRING CYLINDER
a.

Check the fuel injector assembly injection (whether fuel volume is high or low, and whether injection pattern is poor).

Click hereEngine / Hybrid System>2AR-FE (FUEL)>FUEL INJECTOR>INSPECTION

HINT:

Perform "Inspection After Repair" after replacing the fuel injector assembly.

Click hereEngine / Hybrid System>2AR-FE (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION



Result:
Proceed to
OK
NG



OK

10.CHECK INTAKE SYSTEM

NG

REPLACE FUEL INJECTOR ASSEMBLY

10.CHECK INTAKE SYSTEM
a.

Check the intake system for vacuum leaks.

Click hereEngine / Hybrid System>2AR-FE (INTAKE / EXHAUST)>INTAKE SYSTEM>ON-VEHICLE INSPECTION

OK:

No leaks from intake system.


HINT:

Perform "Inspection After Repair" after repairing or replacing the intake system.

Click hereEngine / Hybrid System>2AR-FE (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION



Result:
Proceed to
OK
NG



OK

11.INSPECT INTAKE AIR CONTROL VALVE ACTUATOR (FOR TUMBLE CONTROL VALVE)

NG

REPAIR OR REPLACE INTAKE SYSTEM

11.INSPECT INTAKE AIR CONTROL VALVE ACTUATOR (FOR TUMBLE CONTROL VALVE)
a.

Inspect the intake air control valve actuator (for tumble control valve).

Click hereEngine / Hybrid System>2AR-FE (INTAKE / EXHAUST)>INTAKE SYSTEM>ON-VEHICLE INSPECTION


Result:
Proceed to
OK
NG



OK

12.CHECK FUEL PRESSURE

NG

REPLACE INTAKE AIR CONTROL VALVE ACTUATOR (FOR TUMBLE CONTROL VALVE)

12.CHECK FUEL PRESSURE

Result:
Proceed to
OK
NG



OK

13.READ VALUE USING GTS (COOLANT TEMP)

NG

39.INSPECT FUEL PUMP
13.READ VALUE USING GTS (COOLANT TEMP)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine and ECT / Data List / Coolant Temp.

Powertrain > Engine and ECT > Data List
Tester Display
Coolant Temp
50003 234 8

e.

Read the Data List twice, when the engine is both cold and warmed up.

Standard:
GTS Display Condition Specified Condition
Coolant Temp Cold engine Same as ambient air temperature
Warm engine Between 75 and 100°C (167 and 212°F)


HINT:

Perform "Inspection After Repair" after replacing the engine coolant temperature sensor.

Click hereEngine / Hybrid System>2AR-FE (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION



Result:
Proceed to
OK
NG



OK

14.READ VALUE USING GTS (INTAKE AIR)

NG

14.READ VALUE USING GTS (INTAKE AIR)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine / Data List / Intake Air.

Powertrain > Engine and ECT > Data List
Tester Display
Intake Air
50003 234 5

e.

According to the display on the GTS, read the Data List.

OK:

Same as actual intake air temperature.



HINT:

Perform "Inspection After Repair" after replacing the mass air flow meter sub-assembly.

Click hereEngine / Hybrid System>2AR-FE (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION


Result:
Proceed to
OK
NG



OK

15.READ VALUE USING GTS (MAF)

NG

REPLACE MASS AIR FLOW METER SUB-ASSEMBLY

15.READ VALUE USING GTS (MAF)
a.

Connect the GTS to the DLC3.


b.

Start the engine.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine and ECT / Data List / All Data / Engine Speed, MAF and Coolant Temp.

Powertrain > Engine and ECT > Data List
Tester Display
Engine Speed
MAF
Coolant Temp
50003 234 9,3,8

e.

Allow the engine to idle until Coolant Temp reaches 75°C (167°F) or higher.


f.

Read MAF with the engine speed at 3000 rpm.

Standard:
GTS Display Condition Specified Condition
MAF Shift lever position: N
A/C: off
Engine Speed: 3000 rpm
Between 8.0 gm/sec and 22.0 gm/sec



Result:
Proceed to
OK
NG



OK

16.CHECK VALVE TIMING (CHECK FOR LOOSE TIMING CHAIN AND JUMPED TEETH)

NG

32.CHECK HARNESS AND CONNECTOR (MASS AIR FLOW METER SUB-ASSEMBLY CONNECTOR CONNECTION)
16.CHECK VALVE TIMING (CHECK FOR LOOSE TIMING CHAIN AND JUMPED TEETH)
a.

Remove the cylinder head cover sub-assembly.


A200659C08
1.021,3.031 0.677,4.375 false 6.313,3.031 6.063,4.323 true 4.292,3.469 3.667,4.406 true 4.313,3.323 4.875,4.365 true 0.938,0.542 1.385,0.719 0.448,0.177 10 false *a 6.208,0.594 6.74,0.771 0.531,0.177 10 false *b 5.969,4.375 6.156,4.563 0.188,0.188 10 false *c 0.583,4.448 0.76,4.635 0.177,0.188 10 false *c 4.823,4.396 5.365,4.677 0.542,0.281 10 false *d 3.563,4.427 4.104,4.708 0.542,0.281 10 false *e
*a Approximately 7° *b Approximately 32°
*c Timing Mark *d "0" Timing Mark
*e Groove - -


b.

Turn the crankshaft pulley and align its groove with the "0" timing mark of the timing chain cover.


c.

Check that the timing marks of the camshaft timing gear assembly and camshaft timing exhaust gear assembly are at the positions shown in the illustration.

HINT:

If the timing marks are not at the positions shown, turn the crankshaft one revolution clockwise.


OK:

Timing marks on camshaft timing gear assembly and camshaft timing exhaust gear assembly are at the positions shown in the illustration.


HINT:

If the result is not as specified, check for mechanical malfunctions that may have affected the valve timing, such as a jumped tooth or stretching of the timing chain.



Result:
Proceed to
OK
NG



OK

32.CHECK HARNESS AND CONNECTOR (MASS AIR FLOW METER SUB-ASSEMBLY CONNECTOR CONNECTION)

NG

29.CHECK ENGINE MECHANICAL SYSTEM
17.CHECK INTAKE SYSTEM
a.

Check the intake system for vacuum leaks.

Click hereEngine / Hybrid System>2AR-FE (INTAKE / EXHAUST)>INTAKE SYSTEM>ON-VEHICLE INSPECTION

OK:

No leaks from intake system.


HINT:

Perform "Inspection After Repair" after repairing or replacing the intake system.

Click hereEngine / Hybrid System>2AR-FE (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION



Result:
Proceed to
OK
NG



OK

18.INSPECT INTAKE AIR CONTROL VALVE ACTUATOR (FOR TUMBLE CONTROL VALVE)

NG

REPAIR OR REPLACE INTAKE SYSTEM

18.INSPECT INTAKE AIR CONTROL VALVE ACTUATOR (FOR TUMBLE CONTROL VALVE)
a.

Inspect the intake air control valve actuator (for tumble control valve).

Click hereEngine / Hybrid System>2AR-FE (INTAKE / EXHAUST)>INTAKE SYSTEM>ON-VEHICLE INSPECTION


Result:
Proceed to
OK
NG



OK

19.CHECK FUEL PRESSURE

NG

REPLACE INTAKE AIR CONTROL VALVE ACTUATOR (FOR TUMBLE CONTROL VALVE)

19.CHECK FUEL PRESSURE

Result:
Proceed to
OK
NG



OK

20.READ VALUE USING GTS (COOLANT TEMP)

NG

39.INSPECT FUEL PUMP
20.READ VALUE USING GTS (COOLANT TEMP)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine and ECT / Data List / Coolant Temp.

Powertrain > Engine and ECT > Data List
Tester Display
Coolant Temp
50003 234 8

e.

Read the Data List twice, when the engine is both cold and warmed up.

Standard:
GTS Display Condition Specified Condition
Coolant Temp Cold engine Same as ambient air temperature
Warm engine Between 75 and 100°C (167 and 212°F)


HINT:

Perform "Inspection After Repair" after replacing the engine coolant temperature sensor.

Click hereEngine / Hybrid System>2AR-FE (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION



Result:
Proceed to
OK
NG



OK

21.READ VALUE USING GTS (INTAKE AIR)

NG

21.READ VALUE USING GTS (INTAKE AIR)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine / Data List / Intake Air.

Powertrain > Engine and ECT > Data List
Tester Display
Intake Air
50003 234 5

e.

According to the display on the GTS, read the Data List.

OK:

Same as actual intake air temperature.



HINT:

Perform "Inspection After Repair" after replacing the mass air flow meter sub-assembly.

Click hereEngine / Hybrid System>2AR-FE (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION


Result:
Proceed to
OK
NG



OK

22.READ VALUE USING GTS (MAF)

NG

REPLACE MASS AIR FLOW METER SUB-ASSEMBLY

22.READ VALUE USING GTS (MAF)
a.

Connect the GTS to the DLC3.


b.

Start the engine.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine and ECT / Data List / All Data / Engine Speed, MAF and Coolant Temp.

Powertrain > Engine and ECT > Data List
Tester Display
Engine Speed
MAF
Coolant Temp
50003 234 9,3,8

e.

Allow the engine to idle until Coolant Temp reaches 75°C (167°F) or higher.


f.

Read MAF with the engine speed at 3000 rpm.

Standard:
GTS Display Condition Specified Condition
MAF Shift lever position: N
A/C: off
Engine Speed: 3000 rpm
Between 8.0 gm/sec and 22.0 gm/sec



Result:
Proceed to
OK
NG



OK

23.CHECK VALVE TIMING (CHECK FOR LOOSE TIMING CHAIN AND JUMPED TEETH)

NG

32.CHECK HARNESS AND CONNECTOR (MASS AIR FLOW METER SUB-ASSEMBLY CONNECTOR CONNECTION)
23.CHECK VALVE TIMING (CHECK FOR LOOSE TIMING CHAIN AND JUMPED TEETH)
a.

Remove the cylinder head cover sub-assembly.


A200659C08
1.021,3.031 0.677,4.375 false 6.313,3.031 6.063,4.323 true 4.292,3.469 3.667,4.406 true 4.313,3.323 4.875,4.365 true 0.938,0.542 1.385,0.719 0.448,0.177 10 false *a 6.208,0.594 6.74,0.771 0.531,0.177 10 false *b 5.969,4.375 6.156,4.563 0.188,0.188 10 false *c 0.583,4.448 0.76,4.635 0.177,0.188 10 false *c 4.823,4.396 5.365,4.677 0.542,0.281 10 false *d 3.563,4.427 4.104,4.708 0.542,0.281 10 false *e
*a Approximately 7° *b Approximately 32°
*c Timing Mark *d "0" Timing Mark
*e Groove - -


b.

Turn the crankshaft pulley and align its groove with the "0" timing mark of the timing chain cover.


c.

Check that the timing marks of the camshaft timing gear assembly and camshaft timing exhaust gear assembly are at the positions shown in the illustration.

HINT:

If the timing marks are not at the positions shown, turn the crankshaft one revolution clockwise.


OK:

Timing marks on camshaft timing gear assembly and camshaft timing exhaust gear assembly are at the positions shown in the illustration.


HINT:

If the result is not as specified, check for mechanical malfunctions that may have affected the valve timing, such as a jumped tooth or stretching of the timing chain.



Result:
Proceed to
OK
NG



OK

24.INSPECT SPARK PLUG

NG

29.CHECK ENGINE MECHANICAL SYSTEM
24.INSPECT SPARK PLUG
a.

Inspect the spark plug of the misfiring cylinder.

Click hereEngine / Hybrid System>2AR-FE (ENGINE CONTROL)>IGNITION SYSTEM>ON-VEHICLE INSPECTION

HINT:

Perform "Inspection After Repair" after replacing the spark plug.

Click hereEngine / Hybrid System>2AR-FE (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION



Result:
Proceed to
OK
NG



OK

25.CHECK FOR SPARK (SPARK TEST)

NG

25.CHECK FOR SPARK (SPARK TEST)
a.

Perform a spark test.

Click hereEngine / Hybrid System>2AR-FE (ENGINE CONTROL)>IGNITION SYSTEM>ON-VEHICLE INSPECTION

HINT:
·

If the result of the spark test is normal, proceed to the next step.

·

Perform "Inspection After Repair" after repairing or replacing the ignition system.

Click hereEngine / Hybrid System>2AR-FE (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION




Result:
Proceed to
NEXT



NEXT

26.CHECK CYLINDER COMPRESSION PRESSURE
26.CHECK CYLINDER COMPRESSION PRESSURE
a.

Measure the cylinder compression pressure of the misfiring cylinder.

Click hereEngine / Hybrid System>2AR-FE (ENGINE MECHANICAL)>ENGINE>ON-VEHICLE INSPECTION

HINT:

Perform "Inspection After Repair" after repairing or replacing the engine assembly.

Click hereEngine / Hybrid System>2AR-FE (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION



Result:
Proceed to
OK
NG



OK

27.CHECK TERMINAL VOLTAGE (#10, #20, #30 AND/OR #40)

NG

CHECK ENGINE TO DETERMINE CAUSE OF LOW COMPRESSION

27.CHECK TERMINAL VOLTAGE (#10, #20, #30 AND/OR #40)
A413245C02
1.333,0.292 1.75,0.563 0.417,0.271 0.792,1.74 1.563,1.031 true 2.875,1.802 2.333,1.115 true 1.24,1.813 1.625,1.052 true 1.875,1.781 1.698,1.042 true 2.292,1.781 1.792,1.042 true 1.406,0.323 1.865,0.521 0.458,0.198 10 false C58 0.146,0.052 0.458,0.25 0.313,0.198 10 false *a 0.615,1.781 1.073,1.979 0.458,0.198 10 false #20 1.073,1.833 1.531,2.031 0.458,0.198 10 false #30 1.74,1.813 2.198,2.01 0.458,0.198 10 false #40 2.188,1.813 2.646,2.01 0.458,0.198 10 false #10 2.771,1.854 3.229,2.052 0.458,0.198 10 false E01
*a Front view of wire harness connector
(to ECM)


a.

Disconnect the ECM connector.


b.

Turn the ignition switch to ON.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
C58-21 (#10) - C58-57 (E01) Ignition switch ON 11 to 14 V
C58-18 (#20) - C58-57 (E01) Ignition switch ON 11 to 14 V
C58-19 (#30) - C58-57 (E01) Ignition switch ON 11 to 14 V
C58-20 (#40) - C58-57 (E01) Ignition switch ON 11 to 14 V



Result:
Proceed to
OK
NG



OK

28.CHECK FUEL INJECTOR ASSEMBLY OF MISFIRING CYLINDER

NG

28.CHECK FUEL INJECTOR ASSEMBLY OF MISFIRING CYLINDER
a.

Check the fuel injector assembly injection (whether fuel volume is high or low, and whether injection pattern is poor).

Click hereEngine / Hybrid System>2AR-FE (FUEL)>FUEL INJECTOR>INSPECTION

HINT:

Perform "Inspection After Repair" after replacing the fuel injector assembly.

Click hereEngine / Hybrid System>2AR-FE (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION



Result:
Proceed to
OK
NG



OK

32.CHECK HARNESS AND CONNECTOR (MASS AIR FLOW METER SUB-ASSEMBLY CONNECTOR CONNECTION)

NG

REPLACE FUEL INJECTOR ASSEMBLY

29.CHECK ENGINE MECHANICAL SYSTEM
a.

Check for mechanical malfunctions that affect the valve timing, such as a jumped tooth or stretching of the timing chain.


HINT:

Perform "Inspection After Repair" after repairing or replacing the engine mechanical system.

Click hereEngine / Hybrid System>2AR-FE (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION


Result:
Proceed to
OK
NG



OK

30.CLEAR DTC

NG

REPAIR OR REPLACE MALFUNCTIONING PARTS, COMPONENT AND AREA

30.CLEAR DTC
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Clear the DTCs.

Powertrain > Engine and ECT > Clear DTCs
50002 234

e.

Turn the ignition switch off and wait for at least 30 seconds.


Result:
Proceed to
NEXT



NEXT

31.CHECK WHETHER DTC OUTPUT RECURS (MISFIRE DTCS)
31.CHECK WHETHER DTC OUTPUT RECURS (MISFIRE DTCS)
a.

Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.


b.

Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.

Powertrain > Engine and ECT > Utility
Tester Display
All Readiness
50005 234 20

c.

Input the DTC: P0300, P0301, P0302, P0303 or P0304.


d.

Check the DTC judgment result.


Result:
Result Proceed to
NORMAL
(DTCs are not output)
A
ABNORMAL
(DTC P0300, P0301, P0302, P0303 or P0304 is output)
B



A

B

32.CHECK HARNESS AND CONNECTOR (MASS AIR FLOW METER SUB-ASSEMBLY CONNECTOR CONNECTION)
32.CHECK HARNESS AND CONNECTOR (MASS AIR FLOW METER SUB-ASSEMBLY CONNECTOR CONNECTION)
a.

Check the connection and terminal contact pressure of connectors and wire harnesses between the mass air flow meter sub-assembly and ECM.

Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>ELECTRONIC CIRCUIT INSPECTION PROCEDURE

HINT:

Repair any problems.



Result:
Proceed to
NEXT



NEXT

33.CLEAR DTC
33.CLEAR DTC
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Clear the DTCs.

Powertrain > Engine and ECT > Clear DTCs
50002 234

e.

Turn the ignition switch off and wait for at least 30 seconds.


Result:
Proceed to
NEXT



NEXT

34.CHECK WHETHER DTC OUTPUT RECURS (MISFIRE DTCS)
34.CHECK WHETHER DTC OUTPUT RECURS (MISFIRE DTCS)
a.

Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.


b.

Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.

Powertrain > Engine and ECT > Utility
Tester Display
All Readiness
50005 234 20

c.

Input the DTC: P0300, P0301, P0302, P0303 or P0304.


d.

Check the DTC judgment result.


Result:
Result Proceed to
NORMAL
(DTCs are not output)
A
ABNORMAL
(DTC P0300, P0301, P0302, P0303 or P0304 is output)
B



A

END

B

35.CHECK HARNESS AND CONNECTOR (MASS AIR FLOW METER SUB-ASSEMBLY - ECM)
35.CHECK HARNESS AND CONNECTOR (MASS AIR FLOW METER SUB-ASSEMBLY - ECM)
a.

Disconnect the mass air flow meter sub-assembly connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C86-5 (VG) - C58-137 (VG) Always Below 1 Ω
C86-4 (E2G) - C58-104 (E2G) Always Below 1 Ω
C86-5 (VG) or C58-137 (VG) - Body ground and other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

36.REPLACE MASS AIR FLOW METER SUB-ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

36.REPLACE MASS AIR FLOW METER SUB-ASSEMBLY
a.

Replace the mass air flow meter sub-assembly.

Click hereEngine / Hybrid System>2AR-FE (ENGINE CONTROL)>MASS AIR FLOW METER>REMOVAL

HINT:
·

If the results of the inspections performed in steps 15 and 22 indicated no problem, proceed to the next step without replacing the mass air flow meter sub-assembly.

·

Perform "Inspection After Repair" after replacing the mass air flow meter sub-assembly.

Click hereEngine / Hybrid System>2AR-FE (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION




Result:
Proceed to
NEXT



NEXT

37.CLEAR DTC
37.CLEAR DTC
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Clear the DTCs.

Powertrain > Engine and ECT > Clear DTCs
50002 234

e.

Turn the ignition switch off and wait for at least 30 seconds.


Result:
Proceed to
NEXT



NEXT

38.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
38.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
a.

Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.


b.

Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.

Powertrain > Engine and ECT > Utility
Tester Display
All Readiness
50005 234 20

c.

Input the DTC: P0300, P0301, P0302, P0303 or P0304.


d.

Check the DTC judgment result.


Result:
Result Proceed to
NORMAL
(DTCs are not output)
A
ABNORMAL
(DTC P0300, P0301, P0302, P0303 or P0304 is output)
B



A

END

B

39.INSPECT FUEL PUMP
a.

HINT:

Perform "Inspection After Repair" after replacing the fuel pump.

Click hereEngine / Hybrid System>2AR-FE (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION


Result:
Proceed to
OK
NG



OK

REPAIR OR REPLACE FUEL LINE

NG