Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM › 2021.02–2022.01
RM33C0E _57 Power Source / Network _065454 NETWORKING _0329710 CAN COMMUNICATION SYSTEM U

NETWORKING  CAN COMMUNICATION SYSTEM  TERMINALS OF ECU  


NOTICE:
·

After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

Before measuring the resistance of the CAN bus, turn the power switch off and leave the vehicle for 1 minute or more without operating the key or any switches, or opening or closing the doors. After that, disconnect the cable from the negative (-) auxiliary battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.

·

This section describes the standard values for all CAN related components.



HINT:
·

The systems (ECUs and sensors) that use CAN communication vary depending on the vehicle and optional equipment. Check which systems (ECUs and sensors) are installed to the vehicle.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>DIAGNOSIS SYSTEM

·

Operating the power switch, any other switches or a door triggers related ECU and sensor communication on the CAN. This communication will cause the resistance value to change.

·

Even after DTCs are cleared, if a DTC is stored again after driving the vehicle for a while, the malfunction may be occurring due to vibration of the vehicle. In such a case, wiggling the ECUs or wire harness while performing the inspection below may help determine the cause of the malfunction.



NO. 1 CAN JUNCTION CONNECTOR


a.

Check the No. 1 CAN junction connector.

i.

Connection diagram

C434905C01
1.26,1.313 1.677,1.615 0.417,0.302 2.688,1.365 2.688,0.781 2.688,0.781 2.521,0.781 true 3.042,1.354 3.042,0.531 3.042,0.531 2.875,0.531 true 3.396,1.344 3.396,0.26 3.396,0.26 3.146,0.26 true 4.104,1.365 4.104,0.542 4.104,0.542 4.271,0.542 true 2.677,1.615 2.677,2.021 2.677,2.021 2.51,2.021 true 3.042,1.604 3.042,2.26 3.042,2.26 2.875,2.26 true 3.396,1.646 3.396,2.563 3.396,2.563 3.229,2.563 true 4.104,1.604 4.104,2.25 4.104,2.25 4.271,2.25 true 0.115,0.063 0.427,0.26 0.313,0.198 10 false *a 1.354,1.385 1.865,1.656 0.51,0.271 10 false A66 1.927,0.708 2.583,0.99 0.656,0.281 10 false CANH*b 2.271,0.458 2.927,0.74 0.656,0.281 10 false CANH*c 2.583,0.188 3.24,0.469 0.656,0.281 10 false CANH*d 4.365,0.469 5.021,0.75 0.656,0.281 10 false CANH*e 1.938,1.948 2.594,2.229 0.656,0.281 10 false CANL*b 2.302,2.177 2.958,2.458 0.656,0.281 10 false CANL*c 2.688,2.479 3.344,2.76 0.656,0.281 10 false CANL*d 4.344,2.167 5,2.448 0.656,0.281 10 false CANL*e
*a Front view of wire harness connector
(to No. 1 CAN Junction Connector)
*b to Millimeter Wave Radar Sensor Assembly
(w/ Front Camera System)
*c to Forward Recognition Camera
(w/ Front Camera System)
*d to Central Gateway ECU (Network Gateway ECU)
*e to No. 5 CAN Junction Connector - -



ii.

Check the connection diagram of the components which are connected to the No. 1 CAN junction connector.

Terminal No. (Symbol) Wiring Color Connected to
A66-1 (CANH) R Millimeter wave radar sensor assembly*
(for Bus 1)
A66-7 (CANL) W
A66-2 (CANH) G Forward recognition camera*
(for Bus 1)
A66-8 (CANL) W
A66-3 (CANH) P Central gateway ECU (network gateway ECU)
(for Bus 1)
A66-9 (CANL) W
A66-5 (CANH) B No. 5 CAN junction connector
(for Bus 1)
A66-11 (CANL) W

*: w/ Front Camera System





NO. 2 CAN JUNCTION CONNECTOR


a.

Check the No. 2 CAN junction connector.

i.

Connection diagram

C434906C01
0.833,1.323 1.313,1.583 0.479,0.26 3.083,1.427 3.083,0.563 3.083,0.563 2.917,0.563 true 4.26,1.438 4.26,0.771 4.26,0.771 4.51,0.771 true 3.25,1.448 3.25,0.333 3.25,0.333 3.083,0.333 true 3.417,1.427 3.417,0.156 3.417,0.156 3.25,0.156 true 4.094,1.438 4.094,0.604 4.094,0.604 4.344,0.604 true 3.573,1.438 3.573,0.104 3.573,0.104 3.74,0.104 true 3.094,1.688 3.094,2.24 3.094,2.24 2.927,2.24 true 4.26,1.698 4.26,2.031 4.26,2.031 4.51,2.031 true 3.26,1.698 3.26,2.417 3.26,2.417 3.094,2.417 true 3.427,1.688 3.427,2.604 3.427,2.604 3.26,2.604 true 4.104,1.688 4.104,2.188 4.104,2.188 4.354,2.188 true 3.938,1.688 3.938,2.354 3.938,2.354 4.188,2.354 true 3.938,1.448 3.938,0.448 3.938,0.448 4.188,0.448 true 3.583,1.677 3.583,2.667 3.583,2.667 3.75,2.667 true 2.271,1.49 2.688,1.49 true 2.281,1.656 2.698,1.656 true 2.917,1.427 2.917,0.75 2.917,0.75 2.75,0.75 true 2.917,1.688 2.917,2.104 2.917,2.104 2.75,2.104 true 4.49,1.479 4.906,1.479 true 4.5,1.646 4.917,1.646 true 3.75,1.448 3.75,0.281 3.75,0.281 4,0.281 true 3.75,1.667 3.75,2.5 3.75,2.5 4,2.5 true 0.188,0.135 0.5,0.333 0.313,0.198 10 false *a 0.958,1.375 1.354,1.583 0.396,0.208 10 false A67 2.188,0.688 2.75,0.938 0.563,0.25 10 false CANH*c 2.344,0.5 2.906,0.75 0.563,0.25 10 false CANH*d 2.708,0.104 3.271,0.354 0.563,0.25 10 false CANH*f 3.802,0.031 4.365,0.281 0.563,0.25 10 false CANH*g 4.24,0.375 4.802,0.625 0.563,0.25 10 false CANH*h 4.24,2.281 4.802,2.531 0.563,0.25 10 false CANL*h 2.188,2.021 2.75,2.271 0.563,0.25 10 false CANL*c 2.344,2.167 2.906,2.354 0.563,0.188 10 false CANL*d 3.823,2.594 4.385,2.781 0.563,0.188 10 false CANL*g 2.719,2.542 3.281,2.729 0.563,0.188 10 false CANL*f 2.521,0.281 3.083,0.531 0.563,0.25 10 false CANH*e 2.531,2.344 3.094,2.531 0.563,0.188 10 false CANL*e 1.677,1.417 2.323,1.667 0.646,0.25 10 false CANH*b 1.708,1.594 2.271,1.844 0.563,0.25 10 false CANL*b 4.979,1.396 5.542,1.646 0.563,0.25 10 false CANH*d 4.99,1.583 5.552,1.771 0.563,0.188 10 false CANL*d 4.406,0.542 5.052,0.792 0.646,0.25 10 false CANH*b 4.427,2.135 4.99,2.385 0.563,0.25 10 false CANL*b 4.583,0.719 5.146,0.969 0.563,0.25 10 false CANH*f 4.583,1.958 5.146,2.146 0.563,0.188 10 false CANL*f 4.083,0.208 4.646,0.458 0.563,0.25 10 false CANH*i 4.073,2.438 4.635,2.688 0.563,0.25 10 false CANL*i
*a Front view of wire harness connector
(to No. 2 CAN Junction Connector)
*b to Brake Booster with Master Cylinder Assembly
*c to No. 3 Junction Connector *d to ECM
*e to Rack and Pinion Power Steering Gear Assembly *f to No. 4 CAN Junction Connector
*g to Brake Actuator Assembly *h to Inverter with Converter Assembly
*i to Battery ECU Assembly
(for Lithium-ion Battery)
- -



ii.

Check the connection diagram of the components which are connected to the No. 2 CAN junction connector.

Terminal No. (Symbol) Wiring Color Connected to
A67-1 (CANH) Y Brake booster with master cylinder assembly
(for Bus 4)
A67-12 (CANL) W
A67-2 (CANH) R No. 3 junction connector
(for Bus 4)
A67-13 (CANL) W
A67-3 (CANH) P ECM
(for Bus 4)
A67-14 (CANL) W
A67-4 (CANH) G Rack and pinion power steering gear assembly
(for Bus 4)
A67-15 (CANL) W
A67-5 (CANH) GR No. 4 CAN junction connector
(for Bus 4)
A67-16 (CANL) W
A67-6 (CANH) B Brake actuator assembly
(for Bus 4)
A67-17 (CANL) W
A67-7 (CANH) Y Battery ECU assembly*
(for Bus 2)
A67-18 (CANL) W
A67-8 (CANH) V Inverter with converter assembly
(for Bus 2)
A67-19 (CANL) W
A67-9 (CANH) LG Brake booster with master cylinder assembly
(for Bus 2)
A67-20 (CANL) W
A67-10 (CANH) L No. 4 CAN junction connector
(for Bus 2)
A67-21 (CANL) W
A67-11 (CANH) B ECM
(for Bus 2)
A67-22 (CANL) W

*: for Lithium-ion Battery





NO. 3 CAN JUNCTION CONNECTOR


a.

Check the No. 3 CAN junction connector.

i.

Connection diagram

C380534C12
0.833,1.323 1.313,1.583 0.479,0.26 3.25,1.427 3.25,0.563 3.25,0.563 3.083,0.563 true 4.271,1.438 4.271,0.677 4.271,0.677 4.438,0.677 true 3.417,1.448 3.417,0.333 3.417,0.333 3.25,0.333 true 3.583,1.427 3.583,0.156 3.583,0.156 3.417,0.156 true 4.094,1.427 4.094,0.51 4.094,0.51 4.26,0.51 true 3.75,1.438 3.75,0.188 3.75,0.188 3.917,0.188 true 3.26,1.688 3.26,2.24 3.26,2.24 3.094,2.24 true 4.26,1.708 4.26,2.125 4.26,2.125 4.427,2.125 true 3.438,1.698 3.438,2.417 3.438,2.417 3.271,2.417 true 3.583,1.688 3.583,2.604 3.583,2.604 3.417,2.604 true 4.094,1.688 4.094,2.313 4.094,2.313 4.26,2.313 true 3.927,1.677 3.927,2.469 3.927,2.469 4.094,2.469 true 3.927,1.438 3.927,0.354 3.927,0.354 4.094,0.354 true 3.781,1.677 3.781,2.625 3.781,2.625 3.948,2.625 true 3.083,1.417 3.083,0.729 3.083,0.729 2.917,0.729 true 3.083,1.698 3.083,2.083 3.083,2.083 2.917,2.083 true 0.188,0.135 0.5,0.333 0.313,0.198 10 false *a 0.927,1.375 1.323,1.583 0.396,0.208 10 false K126 2.333,0.667 2.896,0.917 0.563,0.25 10 false CANH*b 2.531,0.479 3.094,0.729 0.563,0.25 10 false CANH*c 2.885,0.094 3.448,0.344 0.563,0.25 10 false CANH*e 3.979,0.115 4.542,0.365 0.563,0.25 10 false CANH*f 4.167,0.281 4.729,0.531 0.563,0.25 10 false CANH*g 4.167,2.406 4.729,2.656 0.563,0.25 10 false CANL*g 2.365,2.021 2.927,2.271 0.563,0.25 10 false CANL*b 2.542,2.167 3.104,2.354 0.563,0.188 10 false CANL*c 4.031,2.552 4.594,2.74 0.563,0.188 10 false CANL*f 2.906,2.542 3.469,2.729 0.563,0.188 10 false CANL*e 2.667,0.271 3.229,0.521 0.563,0.25 10 false CANH*d 2.719,2.344 3.281,2.531 0.563,0.188 10 false CANL*d 4.333,0.448 4.979,0.698 0.646,0.25 10 false CANH*h 4.333,2.24 4.896,2.49 0.563,0.25 10 false CANL*h 4.521,0.604 5.083,0.854 0.563,0.25 10 false CANH*i 4.51,2.042 5.073,2.229 0.563,0.188 10 false CANL*i
*a Front view of wire harness connector
(to No. 3 CAN Junction Connector)
*b to No. 1 Junction Connector
*c to Certification ECU (Smart Key ECU Assembly) *d to Combination Meter Assembly
*e to Main Body ECU (Multiplex Network Body ECU) *f to Air Conditioning Amplifier Assembly
*g to Headlight ECU Sub-assembly LH
(w/ Automatic Headlight Beam Level Control System)
*h to Meter Mirror Sub-assembly
(w/ Headup Display System)
*i to Multiplex Tilt and Telescopic ECU
(w/ Power Tilt and Power Telescopic System)
- -



ii.

Check the connection diagram of the components which are connected to the No. 3 CAN junction connector.

Terminal No. (Symbol) Wiring Color Connected to
K126-3 (CANH) P No. 1 junction connector
(for Bus 5)
K126-14 (CANL) W
K126-4 (CANH) G Certification ECU (smart key ECU assembly)
(for Bus 5)
K126-15 (CANL) W
K126-5 (CANH) B Combination meter assembly
(for Bus 5)
K126-16 (CANL) W
K126-6 (CANH) BE Main body ECU (multiplex network body ECU)
(for Bus 5)
K126-17 (CANL) W
K126-7 (CANH) SB Air conditioning amplifier assembly
(for Bus 5)
K126-18 (CANL) W
K126-8 (CANH) L Headlight ECU sub-assembly LH*1
(for Bus 5)
K126-19 (CANL) W
K126-9 (CANH) LG Meter mirror sub-assembly*2
(for Bus 5)
K126-20 (CANL) W
K126-10 (CANH) R Multiplex tilt and telescopic ECU*3
(for Bus 5)
K126-21 (CANL) W

·

*1: w/ Automatic Headlight Beam Level Control System

·

*2: w/ Headup Display System

·

*3: w/ Power Tilt and Power Telescopic System





NO. 4 CAN JUNCTION CONNECTOR


a.

Check the No. 4 CAN junction connector.

i.

Connection diagram

C402508C71
0.854,1.323 1.333,1.583 0.479,0.26 4.427,1.438 4.427,0.677 4.427,0.677 4.594,0.677 true 3.594,1.448 3.594,0.333 3.594,0.333 3.427,0.333 true 4.26,1.427 4.26,0.51 4.26,0.51 4.427,0.51 true 4.417,1.708 4.417,2.125 4.417,2.125 4.583,2.125 true 3.594,1.698 3.594,2.417 3.594,2.417 3.427,2.417 true 4.26,1.688 4.26,2.313 4.26,2.313 4.427,2.313 true 4.094,1.688 4.094,2.479 4.094,2.479 4.26,2.479 true 4.094,1.438 4.094,0.354 4.094,0.354 4.26,0.354 true 2.75,1.427 2.75,0.75 2.75,0.75 2.583,0.75 true 2.771,1.688 2.771,2.104 2.771,2.104 2.604,2.104 true 3.76,1.438 3.76,0.188 3.76,0.188 3.594,0.188 true 3.771,1.708 3.771,2.573 3.771,2.573 3.604,2.573 true 0.188,0.135 0.5,0.333 0.313,0.198 10 false *a 0.958,1.375 1.354,1.583 0.396,0.208 10 false K127 2.042,0.688 2.604,0.938 0.563,0.25 10 false CANH*b 4.323,0.271 4.885,0.521 0.563,0.25 10 false CANH*b 3.063,2.51 3.625,2.729 0.563,0.219 10 false CANL*d 2.073,2.021 2.635,2.271 0.563,0.25 10 false CANL*b 2.844,0.271 3.406,0.521 0.563,0.25 10 false CANH*c 2.865,2.344 3.427,2.531 0.563,0.188 10 false CANL*c 4.521,0.427 5.167,0.677 0.646,0.25 10 false CANH*e 4.323,2.396 4.885,2.646 0.563,0.25 10 false CANL*b 4.656,0.604 5.219,0.854 0.563,0.25 10 false CANH*b 4.667,2.042 5.229,2.229 0.563,0.188 10 false CANL*b 3.021,0.104 3.667,0.354 0.646,0.25 10 false CANH*d 4.49,2.219 5.052,2.469 0.563,0.25 10 false CANL*e
*a Front view of wire harness connector
(to No. 4 CAN Junction Connector)
*b to Central Gateway ECU (Network Gateway ECU)
*c to No. 2 CAN Junction Connector *d to Steering Sensor
*e to Telematics Transceiver
(w/ Telematics Transceiver)
- -



ii.

Check the connection diagram of the components which are connected to the No. 4 CAN junction connector.

Terminal No. (Symbol) Wiring Color Connected to
K127-1 (CANH) SB Central gateway ECU (network gateway ECU)
(for Bus 2)
K127-12 (CANL) W
K127-6 (CANH) SB No. 2 CAN junction connector
(for Bus 4)
K127-17 (CANL) W
K127-7 (CANH) G Steering sensor
(for Bus 4)
K127-18 (CANL) W
K127-9 (CANH) L Central gateway ECU (network gateway ECU)
(for Bus 3)
K127-20 (CANL) W
K127-10 (CANH) R Telematics transceiver*
(for Bus 3)
K127-21 (CANL) W
K127-11 (CANH) GR Central gateway ECU (network gateway ECU)
(for Bus 3)
K127-22 (CANL) W

*: w/ Telematics Transceiver




b.

Check the No. 4 CAN junction connector.

i.

Connection diagram

C421904C14
0.854,1.323 1.333,1.583 0.479,0.26 2.75,1.427 2.75,0.75 2.75,0.75 2.583,0.75 true 2.771,1.688 2.771,2.104 2.771,2.104 2.604,2.104 true 4.417,1.427 4.417,0.667 4.417,0.667 4.667,0.667 true 4.417,1.667 4.417,2.083 4.417,2.083 4.667,2.083 true 3.604,1.688 3.604,2.604 3.604,2.604 3.438,2.604 true 3.583,1.438 3.583,0.177 3.583,0.177 3.417,0.177 true 4.083,1.417 4.083,0.167 4.083,0.167 4.333,0.167 true 4.083,1.667 4.083,2.583 4.083,2.583 4.333,2.583 true 3.083,1.427 3.083,0.583 3.083,0.583 2.917,0.583 true 3.094,1.708 3.094,2.292 3.094,2.292 2.927,2.292 true 3.417,1.438 3.417,0.344 3.417,0.344 3.25,0.344 true 3.438,1.698 3.438,2.448 3.438,2.448 3.271,2.448 true 4.26,1.427 4.26,0.427 4.26,0.427 4.51,0.427 true 4.25,1.698 4.25,2.281 4.25,2.281 4.5,2.281 true 0.188,0.135 0.5,0.333 0.313,0.198 10 false *a 0.948,1.375 1.344,1.583 0.396,0.208 10 false K128 2.042,0.688 2.604,0.938 0.563,0.25 10 false CANH*b 2.073,2.021 2.635,2.271 0.563,0.25 10 false CANL*b 2.313,0.51 2.875,0.76 0.563,0.25 10 false CANH*c 2.396,2.198 2.958,2.448 0.563,0.25 10 false CANL*c 2.74,2.354 3.302,2.604 0.563,0.25 10 false CANL*d 2.677,0.271 3.24,0.521 0.563,0.25 10 false CANH*d 4.406,2.5 4.969,2.75 0.563,0.25 10 false CANL*d 4.417,0.094 4.979,0.344 0.563,0.25 10 false CANH*d 4.76,2 5.323,2.25 0.563,0.25 10 false CANL*g 4.76,0.594 5.323,0.844 0.563,0.25 10 false CANH*g 2.854,0.083 3.417,0.333 0.563,0.25 10 false CANH*e 2.917,2.542 3.5,2.719 0.583,0.177 10 false CANL*e 4.583,0.354 5.146,0.604 0.563,0.25 10 false CANH*f 4.552,2.219 5.115,2.469 0.563,0.25 10 false CANL*f
*a Front view of wire harness connector
(to No. 4 CAN Junction Connector)
*b to Radio and Display Receiver Assembly
(w/ Radio and Display Type)
*c to Option Connector (Bus Buffer ECU)
(w/ CAN Compatible Optional Devices)
*d to Hybrid Vehicle Control ECU Assembly
*e to Airbag Sensor Assembly *f to Vehicle Approaching Speaker Controller
(w/ Vehicle Proximity Notification System)
*g to No. 2 CAN Junction Connector - -



ii.

Check the connection diagram of the components which are connected to the No. 4 CAN junction connector.

Terminal No. (Symbol) Wiring Color Connected to
K128-1 (CANH) B Radio and display receiver assembly*1
(for Bus 3)
K128-12 (CANL) W
K128-3 (CANH) LG Option connector (bus buffer ECU)*2
(for Bus 3)
K128-14 (CANL) W
K128-5 (CANH) V Hybrid vehicle control ECU assembly
(for Bus 4)
K128-16 (CANL) W
K128-6 (CANH) R Airbag sensor assembly
(for Bus 4)
K128-17 (CANL) W
K128-9 (CANH) L Hybrid vehicle control ECU assembly
(for Bus 2)
K128-20 (CANL) W
K128-10 (CANH) Y Vehicle approaching speaker controller*3
(for Bus 2)
K128-21 (CANL) W
K128-11 (CANH) G No. 2 CAN junction connector
(for Bus 2)
K128-22 (CANL) W

·

*1: w/ Radio and Display Type

·

*2: w/ CAN Compatible Optional Devices

·

*3: w/ Vehicle Proximity Notification System





NO. 5 CAN JUNCTION CONNECTOR


a.

Check the No. 5 CAN junction connector.

i.

Connection diagram

C451582C01
1.083,1.25 1.594,1.5 0.51,0.25 2.365,0.781 2.51,0.781 2.51,0.781 2.51,1.344 true 2.354,1.958 2.5,1.958 2.5,1.958 2.5,1.563 true 2.594,0.51 2.74,0.51 2.74,0.51 2.74,1.365 true 3.375,0.271 3.219,0.271 3.219,0.271 3.219,1.354 true 3.635,0.5 3.458,0.5 3.458,0.5 3.458,1.354 true 2.594,2.177 2.74,2.177 2.74,2.177 2.74,1.563 true 3.385,2.417 3.229,2.417 3.229,2.417 3.229,1.573 true 3.635,2.177 3.469,2.177 3.469,2.177 3.469,1.563 true 2.823,0.26 2.99,0.26 2.99,0.26 2.99,1.344 true 2.823,2.406 2.99,2.406 2.99,2.406 2.99,1.563 true 4.438,0.771 4.188,0.771 4.188,0.771 4.188,1.354 true 4.354,1.99 4.188,1.99 4.188,1.99 4.188,1.573 true 0.115,0.073 0.427,0.271 0.313,0.198 10 false *a 1.792,0.698 2.448,0.958 0.656,0.26 10 false CANH*b 1.802,1.875 2.458,2.135 0.656,0.26 10 false CANL*b 1.198,1.302 1.854,1.563 0.656,0.26 10 false R98 2.031,0.427 2.688,0.688 0.656,0.26 10 false CANH*c 3.469,0.188 4.125,0.448 0.656,0.26 10 false CANH*e 3.719,0.427 4.375,0.688 0.656,0.26 10 false CANH*f 2.042,2.094 2.698,2.354 0.656,0.26 10 false CANL*c 3.469,2.333 4.125,2.594 0.656,0.26 10 false CANL*e 3.719,2.094 4.375,2.354 0.656,0.26 10 false CANL*f 2.26,0.177 2.917,0.438 0.656,0.26 10 false CANH*d 2.292,2.333 2.948,2.594 0.656,0.26 10 false CANL*d 4.51,0.698 5.167,0.958 0.656,0.26 10 false CANH*g 4.427,1.927 5.083,2.188 0.656,0.26 10 false CANL*g
*a Front view of wire harness connector
(to No. 5 CAN Junction Connector)
*b to Central Gateway ECU (Network Gateway ECU)
*c to Clearance Warning ECU Assembly
(w/ Parking Support Alert System)
*d to Blind Spot Monitor Sensor RH
(w/ Blind Spot Monitor System)
*e to Rear Television Camera Assembly
(w/ Parking Assist Monitor System)
*f to No. 1 CAN Junction Connector
*g to Television Camera Controller
(w/ Panoramic View Monitor System)
- -



ii.

Check the connection diagram of the components which are connected to the No. 5 CAN junction connector.

Terminal No. (Symbol) Wiring Color Connected to
R98-1 (CANH) GR Central gateway ECU (network gateway ECU)
(for Bus 1)
R98-11 (CANL) W
R98-2 (CANH) L Clearance warning ECU assembly*1
(for Bus 1)
R98-12 (CANL) W
R98-3 (CANH) BE Blind spot monitor sensor RH*2
(for Bus 1)
R98-13 (CANL) W
R98-4 (CANH) R Rear television camera assembly*3
(for Bus 1)
R98-14 (CANL) W
R98-5 (CANH) B No. 1 CAN junction connector
(for Bus 1)
R98-15 (CANL) W
R98-8 (CANH) GR Television camera controller*4
(for Bus 1)
R98-18 (CANL) W

·

*1: w/ Parking Support Alert System

·

*2: w/ Blind Spot Monitor System

·

*3: w/ Parking Assist Monitor System or Panoramic View Monitor System

·

*4: w/ Panoramic View Monitor System





NO. 1 JUNCTION CONNECTOR


a.

Check the No. 1 junction connector.

i.

Connection diagram

C380534C89
0.854,1.323 1.333,1.583 0.479,0.26 3.083,1.448 3.083,0.333 3.083,0.333 2.917,0.333 true 3.094,1.698 3.094,2.417 3.094,2.417 2.927,2.417 true 3.26,1.677 3.26,2.469 3.26,2.469 3.427,2.469 true 3.25,1.438 3.25,0.354 3.25,0.354 3.417,0.354 true 2.75,1.427 2.75,0.75 2.75,0.75 2.583,0.75 true 2.771,1.688 2.771,2.104 2.771,2.104 2.604,2.104 true 0.188,0.135 0.5,0.333 0.313,0.198 10 false *a 0.958,1.375 1.354,1.583 0.396,0.208 10 false R94 1.917,0.688 2.635,0.958 0.719,0.271 10 false CANH*b*c 3.5,0.271 4.333,0.552 0.833,0.281 10 false CANH*e*f 3.51,2.385 4.344,2.625 0.833,0.24 10 false CANL*e*f 1.948,2.021 2.677,2.26 0.729,0.24 10 false CANL*b*c 2.354,0.26 2.917,0.51 0.563,0.25 10 false CANH*d 2.396,2.344 2.958,2.531 0.563,0.188 10 false CANL*d
*a Front view of wire harness connector
(to No. 1 Junction Connector)
*b to Outer Mirror Control ECU Assembly (for Driver Side)
(for LHD with Seat Position Memory System)
*c to Outer Mirror Control ECU Assembly (for Front Passenger Side)
(for RHD with Seat Position Memory System)
*d to No. 3 CAN Junction Connector
*e to No. 5 Junction Connector
(for RHD)
*f to No. 6 Junction Connector
(for LHD)



ii.

Check the connection diagram of the components which are connected to the No. 1 junction connector.

Terminal No. (Symbol) Wiring Color Connected to
R94-1 (CANH) LG Outer mirror control ECU assembly (for driver side)*1
(for Bus 5)
R94-12 (CANL) W
R94-1 (CANH) LG Outer mirror control ECU assembly (for front passenger side)*2
(for Bus 5)
R94-12 (CANL) W
R94-3 (CANH) B No. 3 CAN junction connector
(for Bus 5)
R94-14 (CANL) W
R94-4 (CANH) L No. 5 junction connector*3
(for Bus 5)
R94-15 (CANL) W
R94-4 (CANH) L No. 6 junction connector*4
(for Bus 5)
R94-15 (CANL) W

·

*1: for LHD with Seat Position Memory System

·

*2: for RHD with Seat Position Memory System

·

*3: for RHD

·

*4: for LHD





NO. 2 JUNCTION CONNECTOR


a.

Check the No. 2 junction connector.

i.

Connection diagram

C380534C91
0.854,1.323 1.333,1.583 0.479,0.26 2.917,1.448 2.917,0.333 2.917,0.333 2.75,0.333 true 2.927,1.698 2.927,2.417 2.927,2.417 2.76,2.417 true 3.094,1.677 3.094,2.469 3.094,2.469 3.26,2.469 true 3.083,1.438 3.083,0.354 3.083,0.354 3.25,0.354 true 2.75,1.427 2.75,0.75 2.75,0.75 2.583,0.75 true 2.771,1.688 2.771,2.104 2.771,2.104 2.604,2.104 true 3.417,1.438 3.417,0.604 3.417,0.604 3.583,0.604 true 3.438,1.698 3.438,2.24 3.438,2.24 3.604,2.24 true 0.188,0.135 0.5,0.333 0.313,0.198 10 false *a 0.958,1.375 1.354,1.583 0.396,0.208 10 false R97 2.042,0.688 2.604,0.938 0.563,0.25 10 false CANH*b 3.344,0.281 4.177,0.563 0.833,0.281 10 false CANH*e*f 3.333,2.406 4.167,2.646 0.833,0.24 10 false CANL*e*f 2.073,2.021 2.635,2.271 0.563,0.25 10 false CANL*b 2.073,0.26 2.802,0.5 0.729,0.24 10 false CANH*c*d 2.083,2.344 2.927,2.583 0.844,0.24 10 false CANL*c*d 3.688,2.156 4.521,2.396 0.833,0.24 10 false CANL*g 3.677,0.531 4.51,0.813 0.833,0.281 10 false CANH*g
*a Front view of wire harness connector
(to No. 2 Junction Connector)
*b to Central Gateway ECU (Network Gateway ECU)
*c to No. 5 Junction Connector
(for RHD)
*d to No. 6 Junction Connector
(for LHD)
*e to Outer Mirror Control ECU Assembly (for Front Passenger Side)
(for LHD with Seat Position Memory System)
*f to Outer Mirror Control ECU Assembly (for Driver Side)
(for RHD with Seat Position Memory System)
*g to Headlight ECU Sub-assembly RH
(w/ Automatic Headlight Beam Level Control System)
- -



ii.

Check the connection diagram of the components which are connected to the No. 2 junction connector.

Terminal No. (Symbol) Wiring Color Connected to
R97-1 (CANH) G Central gateway ECU (network gateway ECU)
(for Bus 5)
R97-12 (CANL) W
R97-2 (CANH) L No. 5 junction connector*1
(for Bus 5)
R97-13 (CANL) W
R97-2 (CANH) L No. 6 junction connector*2
(for Bus 5)
R97-13 (CANL) W
R97-3 (CANH) GR Outer mirror control ECU assembly (for front passenger side)*3
(for Bus 5)
R97-14 (CANL) W
R97-3 (CANH) GR Outer mirror control ECU assembly (for driver side)*4
(for Bus 5)
R97-14 (CANL) W
R97-5 (CANH) G Headlight ECU sub-assembly RH*5
(for Bus 5)
R97-16 (CANL) W

·

*1: for RHD

·

*2: for LHD

·

*3: for LHD with Seat Position Memory System

·

*4: for RHD with Seat Position Memory System

·

*5: w/ Automatic Headlight Beam Level Control System





NO. 3 JUNCTION CONNECTOR


a.

Check the No. 3 junction connector.

i.

Connection diagram

C380534C27
0.854,1.323 1.333,1.583 0.479,0.26 4.094,1.448 4.094,0.333 4.094,0.333 3.927,0.333 true 4.094,1.698 4.094,2.417 4.094,2.417 3.927,2.417 true 4.26,1.688 4.26,2.479 4.26,2.479 4.427,2.479 true 4.26,1.438 4.26,0.354 4.26,0.354 4.427,0.354 true 3.927,1.427 3.927,0.667 3.927,0.667 3.76,0.667 true 3.906,1.698 3.906,2.198 3.906,2.198 3.74,2.198 true 4.427,1.438 4.427,0.604 4.427,0.604 4.594,0.604 true 4.417,1.698 4.417,2.24 4.417,2.24 4.583,2.24 true 0.188,0.135 0.5,0.333 0.313,0.198 10 false *a 0.958,1.375 1.354,1.583 0.396,0.208 10 false R99 3.188,0.583 3.75,0.833 0.563,0.25 10 false CANH*b 4.531,0.271 5.365,0.552 0.833,0.281 10 false CANH*d 4.51,2.385 5.344,2.625 0.833,0.24 10 false CANL*d 3.198,2.125 3.76,2.375 0.563,0.25 10 false CANL*b 3.354,0.26 4.083,0.5 0.729,0.24 10 false CANH*c 3.385,2.354 4.229,2.594 0.844,0.24 10 false CANL*c 4.656,2.146 5.49,2.385 0.833,0.24 10 false CANL*e 4.667,0.531 5.5,0.813 0.833,0.281 10 false CANH*e
*a Front view of wire harness connector
(to No. 3 Junction Connector)
*b to Tire Pressure Warning ECU and Receiver
(w/ Tire Pressure Warning System and Tire Inflation Pressure Display Function)
*c to Occupant Detection ECU
(w/ Occupant Classification System)
*d to Central Gateway ECU (Network Gateway ECU)
*e to No. 2 CAN Junction Connector - -



ii.

Check the connection diagram of the components which are connected to the No. 3 junction connector.

Terminal No. (Symbol) Wiring Color Connected to
R99-8 (CANH) L Tire pressure warning ECU and receiver*1
(for Bus 4)
R99-19 (CANL) W
R99-9 (CANH) GR Occupant detection ECU*2
(for Bus 4)
R99-20 (CANL) W
R99-10 (CANH) G Central gateway ECU (network gateway ECU)
(for Bus 4)
R99-21 (CANL) W
R99-11 (CANH) LG No. 2 CAN junction connector
(for Bus 4)
R99-22 (CANL) W

·

*1: w/ Tire Pressure Warning System and Tire Inflation Pressure Display Function

·

*2: w/ Occupant Classification System





NO. 5 JUNCTION CONNECTOR (for RHD)


a.

Check the No. 5 junction connector.

i.

Connection diagram

C380534C18
0.854,1.323 1.333,1.583 0.479,0.26 3.583,1.448 3.583,0.333 3.583,0.333 3.417,0.333 true 3.604,1.698 3.604,2.417 3.604,2.417 3.438,2.417 true 3.417,1.427 3.417,0.667 3.417,0.667 3.25,0.667 true 3.427,1.698 3.427,2.198 3.427,2.198 3.26,2.198 true 3.75,1.438 3.75,0.604 3.75,0.604 3.917,0.604 true 3.76,1.698 3.76,2.24 3.76,2.24 3.927,2.24 true 0.188,0.135 0.5,0.333 0.313,0.198 10 false *a 0.948,1.375 1.344,1.583 0.396,0.208 10 false R100 2.688,0.583 3.25,0.833 0.563,0.25 10 false CANH*b 2.719,2.125 3.281,2.375 0.563,0.25 10 false CANL*b 2.875,0.26 3.604,0.5 0.729,0.24 10 false CANH*c 2.906,2.354 3.75,2.594 0.844,0.24 10 false CANL*c 4,2.146 4.833,2.385 0.833,0.24 10 false CANL*d 3.99,0.521 4.823,0.802 0.833,0.281 10 false CANH*d
*a Front view of wire harness connector
(to No. 5 Junction Connector)
*b to No. 2 Junction Connector
*c to No. 1 Junction Connector *d to Position Control ECU Assembly RH
(w/ Seat Position Memory System)



ii.

Check the connection diagram of the components which are connected to the No. 5 junction connector.

Terminal No. (Symbol) Wiring Color Connected to
R100-5 (CANH) L No. 2 junction connector
(for Bus 5)
R100-16 (CANL) W
R100-6 (CANH) L No. 1 junction connector
(for Bus 5)
R100-17 (CANL) W
R100-7 (CANH) G Position control ECU assembly RH*
(for Bus 5)
R100-18 (CANL) W

*: w/ Seat Position Memory System





NO. 6 JUNCTION CONNECTOR (for LHD)


a.

Check the No. 6 junction connector.

i.

Connection diagram

C380534C92
0.854,1.323 1.333,1.583 0.479,0.26 3.083,1.427 3.083,0.677 3.083,0.677 3.25,0.677 true 3.094,1.688 3.094,2.188 3.094,2.188 3.26,2.188 true 2.75,1.427 2.75,0.677 2.75,0.677 2.583,0.677 true 2.917,1.417 2.917,0.417 2.917,0.417 2.75,0.417 true 2.76,1.688 2.76,2.188 2.76,2.188 2.594,2.188 true 2.927,1.688 2.927,2.438 2.927,2.438 2.76,2.438 true 0.188,0.135 0.5,0.333 0.313,0.198 10 false *a 0.938,1.375 1.333,1.583 0.396,0.208 10 false R101 2.01,0.604 2.573,0.854 0.563,0.25 10 false CANH*b 2.052,2.115 2.615,2.365 0.563,0.25 10 false CANL*b 2.188,0.344 2.917,0.583 0.729,0.24 10 false CANH*c 3.313,2.115 4.156,2.354 0.844,0.24 10 false CANL*d 3.333,0.604 4.063,0.844 0.729,0.24 10 false CANH*d 2.229,2.354 3.073,2.594 0.844,0.24 10 false CANL*c
*a Front view of wire harness connector
(to No. 6 Junction Connector)
*b to No. 2 Junction Connector
*c to No. 1 Junction Connector *d to Position Control ECU Assembly LH
(w/ Seat Position Memory System)



ii.

Check the connection diagram of the components which are connected to the No. 6 junction connector.

Terminal No. (Symbol) Wiring Color Connected to
R101-1 (CANH) L No. 2 junction connector
(for Bus 5)
R101-12 (CANL) W
R101-2 (CANH) L No. 1 junction connector
(for Bus 5)
R101-13 (CANL) W
R101-3 (CANH) G Position control ECU assembly LH*
(for Bus 5)
R101-14 (CANL) W

*: w/ Seat Position Memory System





DLC3


a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.

Measure the resistance according to the value(s) in the table below.

C349818C49
1.625,1.313 2.042,1.583 0.417,0.271 3.865,1.125 3.865,0.51 3.865,0.51 4.052,0.51 true 3.51,1.125 3.51,0.51 3.51,0.51 3.313,0.51 true 4.417,2.24 4.229,2.24 4.229,2.24 4.229,1.708 true 3.667,2.24 3.865,2.24 3.865,2.24 3.865,1.708 true 0.104,0.083 0.417,0.281 0.313,0.198 10 false *1 4.156,0.458 4.792,0.688 0.635,0.229 10 false CANH 3.26,2.198 3.896,2.427 0.635,0.229 10 false CANL 3.042,0.469 3.677,0.698 0.635,0.229 10 false CG 4.51,2.177 5.146,2.406 0.635,0.229 10 false BAT 1.677,1.375 2.313,1.604 0.635,0.229 10 false K154
*1 DLC3 - -


Standard Resistance:
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
K154-6 (CANH) - K154-14 (CANL) B - W HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) auxiliary battery terminal 54 to 69 Ω
K154-6 (CANH) - K154-4 (CG) B - W-B HIGH-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
K154-14 (CANL) - K154-4 (CG) W - W-B LOW-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
K154-6 (CANH) - K154-16 (BAT) B - R HIGH-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher
K154-14 (CANL) - K154-16 (BAT) W - R LOW-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher




CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU)


C372334C05
1.135,1.271 1.49,1.51 0.354,0.24 2.698,2.083 2.865,2.083 2.865,2.083 2.865,1.49 true 3.01,0.177 3.177,0.177 3.177,0.177 3.177,1.344 true 2.927,0.354 3.094,0.354 3.094,0.354 3.094,1.344 true 2.833,0.552 3,0.552 3,0.552 3,1.344 true 2.75,0.76 2.917,0.76 2.917,0.76 2.917,1.344 true 4.063,0.76 3.896,0.76 3.896,0.76 3.896,1.344 true 3.75,0.458 3.583,0.458 3.583,0.458 3.583,1.448 true 3.656,0.26 3.49,0.26 3.49,0.26 3.49,1.448 true 2.802,2.25 2.969,2.25 2.969,2.25 2.969,1.5 true 2.969,2.427 3.135,2.427 3.135,2.427 3.135,1.49 true 3.063,2.594 3.229,2.594 3.229,2.594 3.229,1.49 true 3.573,2.542 3.406,2.542 3.406,2.542 3.406,1.49 true 3.479,2.698 3.313,2.698 3.313,2.698 3.313,1.479 true 3.854,2.396 3.688,2.396 3.688,2.396 3.688,1.479 true 3.938,2.229 3.771,2.229 3.771,2.229 3.771,1.479 true 4.021,2.073 3.854,2.073 3.854,2.073 3.854,1.49 true 0.073,0.042 0.385,0.24 0.313,0.198 10 false *a 1.198,1.323 1.51,1.521 0.313,0.198 10 false K76 2.323,0.698 2.885,0.906 0.563,0.208 10 false CAXH 2.438,0.49 3,0.698 0.563,0.208 10 false CA1L 2.521,0.302 3.083,0.51 0.563,0.208 10 false CA2L 2.583,0.115 3.146,0.323 0.563,0.208 10 false CA3H 3.74,0.188 4.302,0.396 0.563,0.208 10 false CA4H 3.844,0.396 4.406,0.604 0.563,0.208 10 false CA4L 4.146,0.688 4.708,0.896 0.563,0.208 10 false CA6L 2.292,2.021 2.854,2.229 0.563,0.208 10 false CAXL 2.385,2.188 2.948,2.396 0.563,0.208 10 false CA1H 2.552,2.365 3.115,2.573 0.563,0.208 10 false CA2H 2.667,2.531 3.229,2.74 0.563,0.208 10 false CA3L 3.563,2.625 4.115,2.792 0.552,0.167 10 false CAYL 3.646,2.479 4.167,2.656 0.521,0.177 10 false CAYH 3.927,2.323 4.448,2.5 0.521,0.177 10 false CA5L 4.021,2.167 4.542,2.344 0.521,0.177 10 false CA5H 4.104,2 4.625,2.177 0.521,0.177 10 false CA6H
*a Component without harness connected
(Central Gateway ECU (Network Gateway ECU))
- -


a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.

Disconnect the K76 central gateway ECU (network gateway ECU) connector.


c.

Measure the resistance according to the value(s) in the table below.

C361640C14
0.917,1.708 1.292,1.979 0.375,0.271 2.021,1.208 2.271,1.208 2.271,1.208 2.271,1.708 true 2.729,0.969 2.979,0.969 2.979,0.969 2.979,1.719 true 2.823,2.625 3.073,2.625 3.073,2.625 3.073,2 true 2.969,2.844 3.219,2.844 3.219,2.844 3.219,2.01 true 5.135,1.156 4.885,1.156 4.885,1.156 4.885,1.719 true 3.26,0.75 3.51,0.75 3.51,0.75 3.51,1.917 true 3.406,0.51 3.656,0.51 3.656,0.51 3.656,1.927 true 3.115,3.021 3.365,3.021 3.365,3.021 3.365,2.021 true 4.333,3.156 4.083,3.156 4.083,3.156 4.083,2 true 4.188,3.365 3.938,3.365 3.938,3.365 3.938,2 true 4.042,3.563 3.792,3.563 3.792,3.563 3.792,2.01 true 4.438,0.417 4.188,0.417 4.188,0.417 4.188,1.719 true 4.479,2.99 4.229,2.99 4.229,2.99 4.229,2.01 true 4.885,2.813 4.635,2.813 4.635,2.813 4.635,2 true 5.073,2.635 4.823,2.635 4.823,2.635 4.823,2 true 4.583,0.604 4.333,0.604 4.333,0.604 4.333,1.729 true 4.771,0.792 4.521,0.792 4.521,0.792 4.521,1.719 true 4.948,0.969 4.698,0.969 4.698,0.969 4.698,1.729 true 1.021,1.76 1.573,2.021 0.552,0.26 10 false K76 0.135,0.073 0.448,0.271 0.313,0.198 10 false *a 1.615,1.135 2.167,1.396 0.552,0.26 10 false BATT 2.333,0.906 2.885,1.167 0.552,0.26 10 false CA6L 2.406,2.552 2.958,2.813 0.552,0.26 10 false CA6H 2.552,2.76 3.104,3.021 0.552,0.26 10 false CA5H 5.229,1.073 5.781,1.333 0.552,0.26 10 false GND 4.521,0.344 5.073,0.604 0.552,0.26 10 false CA3H 2.99,0.438 3.542,0.698 0.552,0.26 10 false CA4H 2.875,0.688 3.427,0.948 0.552,0.26 10 false CA4L 2.719,2.948 3.271,3.208 0.552,0.26 10 false CA5L 4.417,3.083 4.969,3.344 0.552,0.26 10 false CA3L 4.271,3.281 4.823,3.542 0.552,0.26 10 false CAYL 4.146,3.479 4.698,3.74 0.552,0.26 10 false CAYH 4.552,2.906 5.104,3.167 0.552,0.26 10 false CA2H 4.969,2.729 5.521,2.99 0.552,0.26 10 false CA1H 5.156,2.552 5.708,2.813 0.552,0.26 10 false CAXL 4.688,0.531 5.24,0.792 0.552,0.26 10 false CA2L 4.844,0.719 5.396,0.979 0.552,0.26 10 false CA1L 5.031,0.896 5.583,1.156 0.552,0.26 10 false CAXH
*a Front view of wire harness connector
(to Central Gateway ECU (Network Gateway ECU))
- -


Standard Resistance:
Diagnosis Bus Branch Lines (DLC3 - Central gateway ECU (network gateway ECU))
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
K76-14 (CA6H) - K76-5 (CA6L) B - W HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) auxiliary battery terminal 1 MΩ or higher
K76-14 (CA6H) - K76-10 (GND) B - W-B HIGH-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
K76-5 (CA6L) - K76-10 (GND) W - W-B LOW-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
K76-14 (CA6H) - K76-1 (BATT) B - BE HIGH-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher
K76-5 (CA6L) - K76-1 (BATT) W - BE LOW-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher

Bus 1 Main Lines
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
K76-23 (CA1H) - K76-9 (CAXH) B - BE HIGH-level CAN bus line - HIGH-level CAN bus line Cable disconnected from negative (-) auxiliary battery terminal Below 1 Ω
K76-8 (CA1L) - K76-24 (CAXL) W - W LOW-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) auxiliary battery terminal Below 1 Ω
K76-23 (CA1H) - K76-10 (GND) B - W-B HIGH-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
K76-8 (CA1L) - K76-10 (GND) W - W-B LOW-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
K76-23 (CA1H) - K76-1 (BATT) B - BE HIGH-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher
K76-8 (CA1L) - K76-1 (BATT) W - BE LOW-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher

Bus 2 Main Lines
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
K76-18 (CA4H) - K76-17 (CA4L) SB - W HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω
K76-18 (CA4H) - K76-10 (GND) SB - W-B HIGH-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
K76-17 (CA4L) - K76-10 (GND) W - W-B LOW-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
K76-18 (CA4H) - K76-1 (BATT) SB - BE HIGH-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher
K76-17 (CA4L) - K76-1 (BATT) W - BE LOW-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher

Bus 3 Main Lines
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
K76-6 (CA3H) - K76-19 (CAYH) L - GR HIGH-level CAN bus line - HIGH-level CAN bus line Cable disconnected from negative (-) auxiliary battery terminal Below 1 Ω
K76-21 (CA3L) - K76-20 (CAYL) W - W LOW-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) auxiliary battery terminal Below 1 Ω
K76-6 (CA3H) - K76-10 (GND) L - W-B HIGH-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
K76-21 (CA3L) - K76-10 (GND) W - W-B LOW-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
K76-6 (CA3H) - K76-1 (BATT) L - BE HIGH-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher
K76-21 (CA3L) - K76-1 (BATT) W - BE LOW-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher

Bus 4 Main Lines
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
K76-22 (CA2H) - K76-7 (CA2L) G - W HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω
K76-22 (CA2H) - K76-10 (GND) G - W-B HIGH-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
K76-7 (CA2L) - K76-10 (GND) W - W-B LOW-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
K76-22 (CA2H) - K76-1 (BATT) G - BE HIGH-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher
K76-7 (CA2L) - K76-1 (BATT) W - BE LOW-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher

Bus 5 Main Lines
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
K76-15 (CA5H) - K76-16 (CA5L) LG - W HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω
K76-15 (CA5H) - K76-10 (GND) LG - W-B HIGH-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
K76-16 (CA5L) - K76-10 (GND) W - W-B LOW-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
K76-15 (CA5H) - K76-1 (BATT) LG - BE HIGH-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher
K76-16 (CA5L) - K76-1 (BATT) W - BE LOW-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher




STEERING SENSOR


C372335C07
4.865,0.177 5.219,0.406 0.354,0.229 2.333,2.094 2.688,2.323 0.354,0.229 5.229,1.948 5.063,1.948 5.063,1.948 5.063,1.385 true 5.229,0.594 5.063,0.594 5.063,0.594 5.063,1.177 true 0.115,0.073 0.427,0.271 0.313,0.198 10 false *a 4.927,0.219 5.24,0.417 0.313,0.198 10 false K71 5.313,1.865 5.813,2.104 0.5,0.24 10 false CANL 5.313,0.521 5.813,0.76 0.5,0.24 10 false CANH 2.438,2.125 2.75,2.323 0.313,0.198 10 false z6
*a Component without harness connected
(Steering Sensor)
- -


a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.

Disconnect the K71 steering sensor connector.


c.
C369124C10
1.479,0.427 1.833,0.677 0.354,0.25 1.542,0.917 1.708,0.917 1.708,0.917 1.708,1.667 true 1.875,2.615 1.708,2.615 1.708,2.615 1.708,2.031 true 1.208,2.615 1.375,2.615 1.375,2.615 1.375,2.031 true 2.052,0.917 1.896,0.917 1.896,0.917 1.896,1.667 true 0.146,0.156 0.458,0.354 0.313,0.198 10 false *a 1.542,0.469 1.854,0.667 0.313,0.198 10 false K71 1.104,0.844 1.563,1.042 0.458,0.198 10 false CANH 1.958,2.542 2.417,2.74 0.458,0.198 10 false CANL 2.146,0.854 2.604,1.052 0.458,0.198 10 false BAT 0.823,2.552 1.281,2.75 0.458,0.198 10 false ESS
*a Front view of wire harness connector
(to Steering Sensor)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
K71-3 (CANH) - K71-8 (CANL) G - W HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) auxiliary battery terminal 54 to 69 Ω
K71-3 (CANH) - K71-6 (ESS) G - W-B HIGH-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
K71-8 (CANL) - K71-6 (ESS) W - W-B LOW-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
K71-3 (CANH) - K71-4 (BAT) G - GR HIGH-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher
K71-8 (CANL) - K71-4 (BAT) W - GR LOW-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher




HYBRID VEHICLE CONTROL ECU ASSEMBLY


Refer to Terminals of ECU.


a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.

Disconnect the K69 and K70 hybrid vehicle control ECU assembly connectors.


c.

Measure the resistance according to the value(s) in the table below.

C366201C02
1.698,0.167 2.198,0.417 0.5,0.25 4.802,0.167 5.302,0.417 0.5,0.25 2.646,1.177 2.646,0.76 2.646,0.76 2.813,0.76 true 4.667,0.615 4.833,0.615 4.833,0.615 4.833,1.198 true 5.354,0.594 5.521,0.594 5.521,0.594 5.521,1.594 true 5.823,0.604 5.656,0.604 5.656,0.604 5.656,1.604 true 5.354,2.302 5.521,2.302 5.521,2.302 5.521,1.885 true 5.823,2.292 5.656,2.292 5.656,2.292 5.656,1.875 true 0.188,0.083 0.5,0.281 0.313,0.198 10 false *a 1.823,0.219 2.135,0.417 0.313,0.198 10 false K69 4.906,0.229 5.219,0.427 0.313,0.198 10 false K70 2.906,0.677 3.219,0.875 0.313,0.198 10 false E1 4.25,0.552 4.729,0.719 0.479,0.167 10 false BATT 4.958,0.521 5.438,0.688 0.479,0.167 10 false CA1L 5.917,0.531 6.396,0.698 0.479,0.167 10 false CA1H 5.896,2.208 6.396,2.375 0.5,0.167 10 false CA3P 4.927,2.219 5.427,2.385 0.5,0.167 10 false CA3N
*a Front view of wire harness connector
(to Hybrid Vehicle Control ECU Assembly)
- -


Standard Resistance:
Bus 2 Branch Lines
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
K70-25 (CA1H) - K70-24 (CA1L) L - W HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) auxiliary battery terminal 54 to 69 Ω
K70-25 (CA1H) - K69-6 (E1) L - W-B HIGH-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
K70-24 (CA1L) - K69-6 (E1) W - W-B LOW-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
K70-25 (CA1H) - K70-3 (BATT) L - V HIGH-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher
K70-24 (CA1L) - K70-3 (BATT) W - V LOW-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher

Bus 4 Branch Lines
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
K70-31 (CA3P) - K70-30 (CA3N) V - W HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) auxiliary battery terminal 54 to 69 Ω
K70-31 (CA3P) - K69-6 (E1) V - W-B HIGH-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
K70-30 (CA3N) - K69-6 (E1) W - W-B LOW-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
K70-31 (CA3P) - K70-3 (BATT) V - V HIGH-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher
K70-30 (CA3N) - K70-3 (BATT) W - V LOW-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher




INVERTER WITH CONVERTER ASSEMBLY


Refer to Terminals of ECU.


a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.

Disconnect the A48 inverter with converter assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

C350876C11
4.99,0.271 5.5,0.521 0.51,0.25 1.875,0.135 2.281,0.417 0.406,0.281 1.688,1.219 1.688,0.406 1.688,0.406 1.542,0.406 true 1.135,1.344 1.656,1.344 true 2.229,1.542 3.063,1.552 true 6,2.135 5.844,2.135 5.844,2.135 5.844,1.667 true 0.135,0.115 0.448,0.313 0.313,0.198 10 false *a 1.094,0.354 1.583,0.594 0.49,0.24 10 false CANH 0.677,1.281 1.167,1.521 0.49,0.24 10 false CANL 3.135,1.49 3.625,1.729 0.49,0.24 10 false GND1 6.073,2.063 6.563,2.302 0.49,0.24 10 false BAT 5.073,0.323 5.563,0.563 0.49,0.24 10 false K154 1.958,0.208 2.448,0.448 0.49,0.24 10 false A48 3.729,0.146 4.042,0.344 0.313,0.198 10 false *1
*1 DLC3 - -
*a Front view of wire harness connector
(to Inverter with Converter Assembly)
- -


Standard Resistance:
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
A48-1 (CANH) - A48-7 (CANL) V - W HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) auxiliary battery terminal 54 to 69 Ω
A48-1 (CANH) - A48-24 (GND1) V - W-B HIGH-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
A48-7 (CANL) - A48-24 (GND1) W - W-B LOW-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
A48-1 (CANH) - K154-16 (BAT) V - R HIGH-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher
A48-7 (CANL) - K154-16 (BAT) W - R LOW-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher




ECM


Refer to Terminals of ECU.


a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.

Disconnect the A22 ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

C381995C01
1.25,1.177 1.677,1.469 0.427,0.292 2.99,0.375 3.156,0.375 3.156,0.375 3.156,1.042 true 4.406,0.438 4.24,0.438 4.24,0.438 4.24,1.104 true 3.5,0.219 3.667,0.219 3.667,0.219 3.667,1.052 true 3.927,0.219 3.76,0.219 3.76,0.219 3.76,1.052 true 3.5,2.448 3.667,2.448 3.667,2.448 3.667,1.198 true 3.927,2.448 3.76,2.448 3.76,2.448 3.76,1.198 true 0.167,0.135 0.479,0.333 0.313,0.198 10 false *a 1.354,1.25 1.667,1.448 0.313,0.198 10 false A22 2.552,0.323 3.052,0.49 0.5,0.167 10 false BATT 4.521,0.365 5.021,0.531 0.5,0.167 10 false E1 3.073,0.146 3.573,0.313 0.5,0.167 10 false CAN+ 4.01,0.146 4.51,0.313 0.5,0.167 10 false CANH 3.104,2.375 3.604,2.542 0.5,0.167 10 false CAN- 4,2.375 4.5,2.542 0.5,0.167 10 false CANL
*a Front view of wire harness connector
(to ECM)
- -


Standard Resistance:
Bus 2 Main Lines
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
A22-8 (CANH) - A22-18 (CANL) B - W HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω
A22-8 (CANH) - A22-10 (E1) B - W-B HIGH-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
A22-18 (CANL) - A22-10 (E1) W - W-B LOW-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
A22-8 (CANH) - A22-1 (BATT) B - G HIGH-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher
A22-18 (CANL) - A22-1 (BATT) W - G LOW-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher

Bus 4 Branch Lines
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
A22-7 (CAN+) - A22-17 (CAN-) P - W HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) auxiliary battery terminal 54 to 69 Ω
A22-7 (CAN+) - A22-10 (E1) P - W-B HIGH-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
A22-17 (CAN-) - A22-10 (E1) W - W-B LOW-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
A22-7 (CAN+) - A22-1 (BATT) P - G HIGH-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher
A22-17 (CAN-) - A22-1 (BATT) W - G LOW-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher




COMBINATION METER ASSEMBLY


Refer to Terminals of ECU.

Click hereVehicle Interior>METER / GAUGE / DISPLAY>METER / GAUGE SYSTEM>TERMINALS OF ECU

a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.

Disconnect the K21 combination meter assembly connector.


c.
C349828C32
1.552,0.615 1.938,0.896 0.385,0.281 1.667,2.917 1.802,2.917 1.802,2.917 1.802,2.125 true 2.083,2.917 1.927,2.917 1.927,2.917 1.927,2.125 true 0.375,2.604 0.51,2.604 0.51,2.604 0.51,2.125 true 2.833,2.625 2.969,2.625 2.969,2.625 2.969,2.125 true 0.135,0.104 0.448,0.302 0.313,0.198 10 false *a 0.125,2.531 0.708,2.833 0.583,0.302 10 false ES 2.177,2.833 2.76,3.135 0.583,0.302 10 false CANH 1.646,0.677 2.229,0.979 0.583,0.302 10 false K21 2.656,2.552 3.24,2.854 0.583,0.302 10 false B 1.219,2.844 1.802,3.146 0.583,0.302 10 false CANL
*a Front view of wire harness connector
(to Combination Meter Assembly)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
K21-32 (CANH) - K21-31 (CANL) B - W HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω
K21-32 (CANH) - K21-21 (ES) B - W-B HIGH-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
K21-31 (CANL) - K21-21 (ES) W - W-B LOW-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
K21-32 (CANH) - K21-40 (B) B - LA-B HIGH-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher
K21-31 (CANL) - K21-40 (B) W - LA-B LOW-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher




BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY


Refer to Terminals of ECU.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>TERMINALS OF ECU

a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.

Disconnect the A40 brake booster with master cylinder assembly connector.


c.
C349830C23
1.542,0.146 1.958,0.417 0.417,0.271 1.625,1.656 1.625,0.625 1.625,0.625 1.75,0.625 true 1.531,1.656 1.531,0.625 1.531,0.625 1.396,0.625 true 1.396,2.604 1.531,2.604 1.531,2.604 1.531,1.948 true 1.76,2.604 1.615,2.604 1.615,2.604 1.615,1.948 true 2.646,1.448 2.646,0.417 2.646,0.417 2.771,0.417 true 2.781,2.542 2.635,2.542 2.635,2.542 2.635,1.885 true 0.094,0.063 0.406,0.26 0.313,0.198 10 false *a 1.625,0.208 2.01,0.5 0.385,0.292 10 false A40 1.833,0.552 2.385,0.833 0.552,0.281 10 false CA2H 1.01,0.552 1.563,0.833 0.552,0.281 10 false CA2L 1,2.531 1.552,2.813 0.552,0.281 10 false CA1L 1.854,2.542 2.406,2.823 0.552,0.281 10 false CA1H 2.844,0.333 3.396,0.615 0.552,0.281 10 false GND1 2.844,2.469 3.146,2.74 0.302,0.271 10 false BS
*a Front view of wire harness connector
(to Brake Booster with Master Cylinder Assembly)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Bus 2 Branch Lines
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
A40-30 (CA2H) - A40-29 (CA2L) LG - W HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) auxiliary battery terminal 54 to 69 Ω
A40-30 (CA2H) - A40-26 (GND1) LG - LA*1
LG - W-B*2
HIGH-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
A40-29 (CA2L) - A40-26 (GND1) W - LA*1
W - W-B*2
LOW-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
A40-30 (CA2H) - A40-52 (BS) LG - LG HIGH-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher
A40-29 (CA2L) - A40-52 (BS) W - LG LOW-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher

Bus 4 Branch Lines
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
A40-43 (CA1H) - A40-42 (CA1L) Y - W HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) auxiliary battery terminal 54 to 69 Ω
A40-43 (CA1H) - A40-26 (GND1) Y - LA*1
Y - W-B*2
HIGH-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
A40-42 (CA1L) - A40-26 (GND1) W - LA*1
W - W-B*2
LOW-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
A40-43 (CA1H) - A40-52 (BS) Y - LG HIGH-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher
A40-42 (CA1L) - A40-52 (BS) W - LG LOW-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher


·

*1: for LHD

·

*2: for RHD




MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)


Refer to Terminals of ECU.

Click hereVehicle Interior>LIGHTING (INT)>LIGHTING SYSTEM>TERMINALS OF ECU

a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.

Disconnect the K52 main body ECU (multiplex network body ECU) connector.


c.

Measure the resistance according to the value(s) in the table below.

C372538C14
5,0.24 5.521,0.49 0.521,0.25 1.792,0.198 2.156,0.438 0.365,0.24 5.135,1.094 5.135,0.688 5.135,0.688 4.979,0.688 true 6.01,2.052 5.844,2.052 5.844,2.052 5.844,1.667 true 2.729,1.156 2.729,0.635 2.729,0.635 2.833,0.635 true 2.604,1.156 2.604,0.333 2.604,0.333 2.708,0.333 true 0.135,0.094 0.448,0.292 0.313,0.198 10 false *a 4.708,0.615 5.208,0.844 0.5,0.229 10 false CG 6.104,1.969 6.604,2.198 0.5,0.229 10 false BAT 1.875,0.24 2.375,0.469 0.5,0.229 10 false K52 5.073,0.281 5.573,0.51 0.5,0.229 10 false K154 2.917,0.563 3.417,0.792 0.5,0.229 10 false CANH 2.802,0.26 3.302,0.49 0.5,0.229 10 false CANL 3.833,0.094 4.146,0.292 0.313,0.198 10 false *1
*1 DLC3 - -
*a Front view of wire harness connector
(to Main Body ECU (Multiplex Network Body ECU))
- -


Standard Resistance:
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
K52-5 (CANH) - K52-4 (CANL) BE - W HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) auxiliary battery terminal 54 to 69 Ω
K52-5 (CANH) - K154-4 (CG) BE - W-B HIGH-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
K52-4 (CANL) - K154-4 (CG) W - W-B LOW-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
K52-5 (CANH) - K154-16 (BAT) BE - R HIGH-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher
K52-4 (CANL) - K154-16 (BAT) W - R LOW-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher




CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)


Refer to Terminals of ECU.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM (for Start Function)>TERMINALS OF ECU

a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.

Disconnect the K62 certification ECU (smart key ECU assembly) connector.


c.
C348744C23
1.5,0.385 1.865,0.667 0.365,0.281 1.198,1.635 1.198,0.875 1.198,0.875 1.375,0.875 true 1.073,1.635 1.073,0.875 1.073,0.875 0.906,0.875 true 2.385,1.646 2.385,0.885 2.385,0.885 2.563,0.885 true 1.24,2.719 1.073,2.719 1.073,2.719 1.073,2.052 true 0.156,0.125 0.469,0.323 0.313,0.198 10 false *a 1.563,0.448 1.875,0.646 0.313,0.198 10 false K62 0.479,0.802 1.115,1 0.635,0.198 10 false CANH 1.458,0.802 2.094,1 0.635,0.198 10 false CANL 2.646,0.802 2.958,1 0.313,0.198 10 false +B 1.302,2.646 1.938,2.844 0.635,0.198 10 false E
*a Front view of wire harness connector
(to Certification ECU (Smart Key ECU Assembly))


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
K62-1 (CANH) - K62-2 (CANL) G - W HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) auxiliary battery terminal 54 to 69 Ω
K62-1 (CANH) - K62-18 (E) G - W-B HIGH-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
K62-2 (CANL) - K62-18 (E) W - W-B LOW-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
K62-1 (CANH) - K62-4 (+B) G - W HIGH-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher
K62-2 (CANL) - K62-4 (+B) W - W LOW-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher




RACK AND PINION POWER STEERING GEAR ASSEMBLY


Refer to Terminals of ECU.

Click hereSteering>POWER ASSIST SYSTEMS>POWER STEERING SYSTEM>TERMINALS OF ECU

a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.

Disconnect the C71 rack and pinion power steering gear assembly connector.


c.
C369118C17
1.5,0.333 1.917,0.583 0.417,0.25 2.406,0.844 2.24,0.844 2.24,0.844 2.24,2.135 true 1.708,2.573 1.708,3.104 1.708,3.104 1.542,3.104 true 1.031,0.833 1.188,0.833 1.188,0.833 1.188,2.125 true 1.844,2.573 1.844,3.104 1.844,3.104 2.01,3.104 true 2.51,0.771 2.927,1 0.417,0.229 10 false PIG 0.563,0.76 1.177,0.958 0.615,0.198 10 false PGND 0.125,0.083 0.74,0.281 0.615,0.198 10 false *a 1.594,0.375 2.208,0.573 0.615,0.198 10 false C71 1.073,3.031 1.688,3.229 0.615,0.198 10 false CANH 2.104,3.031 2.719,3.229 0.615,0.198 10 false CANL
*a Front view of wire harness connector
(to Rack and Pinion Power Steering Gear Assembly)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
C71-10 (CANH) - C71-11 (CANL) G - W HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) auxiliary battery terminal 54 to 69 Ω
C71-10 (CANH) - C71-7 (PGND) G - B HIGH-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
C71-11 (CANL) - C71-7 (PGND) W - B LOW-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
C71-10 (CANH) - C71-8 (PIG) G - W HIGH-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher
C71-11 (CANL) - C71-8 (PIG) W - W LOW-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher




AIRBAG SENSOR ASSEMBLY


Refer to Terminals of ECU.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>TERMINALS OF ECU

a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.

Disconnect the K73 airbag sensor assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

C372541C14
1.802,0.188 2.167,0.448 0.365,0.26 5.094,0.292 5.573,0.563 0.479,0.271 5.938,1.677 5.938,2.104 5.938,2.104 6.094,2.104 true 2.354,1.656 2.948,2.323 2.948,2.323 3.104,2.323 true 2.479,1.656 2.927,1.854 2.927,1.854 3.083,1.854 true 2.125,1.99 2.125,2.51 2.125,2.51 1.958,2.51 true 0.135,0.063 0.448,0.26 0.313,0.198 10 false *a 3.708,0.094 4.021,0.292 0.313,0.198 10 false *1 1.875,0.25 2.188,0.448 0.313,0.198 10 false K73 5.167,0.354 5.635,0.604 0.469,0.25 10 false K154 6.198,2.031 6.604,2.281 0.406,0.25 10 false BAT 3.188,1.771 3.635,2.031 0.448,0.26 10 false CANL 3.188,2.25 3.635,2.51 0.448,0.26 10 false CANH 1.708,2.438 2.188,2.646 0.479,0.208 10 false E1
*1 DLC3 - -
*a Front view of wire harness connector
(to Airbag Sensor Assembly)
- -


Standard Resistance:
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
K73-26 (CANH) - K73-27 (CANL) R - W HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω
K73-26 (CANH) - K73-33 (E1) R - W-B HIGH-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
K73-27 (CANL) - K73-33 (E1) W - W-B LOW-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
K73-26 (CANH) - K154-16 (BAT) R - R HIGH-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher
K73-27 (CANL) - K154-16 (BAT) W - R LOW-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher




AIR CONDITIONING AMPLIFIER ASSEMBLY


Refer to Terminals of ECU.

Click hereVehicle Interior>HEATING / AIR CONDITIONING>AIR CONDITIONING SYSTEM>TERMINALS OF ECU

a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.

Disconnect the K54 air conditioning amplifier assembly connector.


c.
C349836C28
1.5,0.208 1.917,0.479 0.417,0.271 1.885,1.833 1.885,0.729 1.885,0.729 2.052,0.729 true 2.021,1.833 2.021,0.938 2.021,0.938 2.188,0.938 true 0.844,1.604 0.844,0.99 0.844,0.99 0.969,0.99 true 2.583,1.604 2.583,1.135 2.583,1.135 2.75,1.135 true 0.083,0.083 0.396,0.281 0.313,0.198 10 false *a 1.615,0.271 2.083,0.563 0.469,0.292 10 false K54 2.146,0.667 2.813,0.875 0.667,0.208 10 false CANH 2.271,0.875 2.938,1.083 0.667,0.208 10 false CANL 2.813,1.063 3.281,1.292 0.469,0.229 10 false GND 1.052,0.917 1.521,1.146 0.469,0.229 10 false B
*a Front view of wire harness connector
(to Air Conditioning Amplifier Assembly)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
K54-11 (CANH) - K54-12 (CANL) SB - W HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) auxiliary battery terminal 54 to 69 Ω
K54-11 (CANH) - K54-4 (GND) SB - W-B HIGH-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
K54-12 (CANL) - K54-4 (GND) W - W-B LOW-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
K54-11 (CANH) - K54-1 (B) SB - LA-B HIGH-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher
K54-12 (CANL) - K54-1 (B) W - LA-B LOW-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher




RADIO AND DISPLAY RECEIVER ASSEMBLY (w/ Radio and Display Type)


Refer to Terminals of ECU.


a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.

Disconnect the K2 radio and display receiver assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

C372569C17
4.948,0.198 5.49,0.469 0.542,0.271 1.771,0.219 2.208,0.51 0.438,0.292 5.125,1.094 5.125,0.688 5.125,0.688 5.271,0.688 true 5.833,1.677 5.833,2.083 5.833,2.083 5.979,2.083 true 2.219,1.438 2.219,0.688 2.219,0.688 2.365,0.688 true 2.104,1.438 2.104,0.688 2.104,0.688 1.938,0.688 true 0.125,0.083 0.438,0.281 0.313,0.198 10 false *a 3.677,0.115 3.99,0.313 0.313,0.198 10 false *1 5.073,0.25 5.677,0.51 0.604,0.26 10 false K154 5.354,0.615 5.729,0.833 0.375,0.219 10 false CG 6.063,2.01 6.49,2.26 0.427,0.25 10 false BAT 1.917,0.292 2.344,0.604 0.427,0.313 10 false K2 1.49,0.615 1.969,0.875 0.479,0.26 10 false CANH 2.448,0.615 2.927,0.875 0.479,0.26 10 false CANL
*1 DLC3 - -
*a Front view of wire harness connector
(to Radio and Display Receiver Assembly)
- -


Standard Resistance:
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
K2-13 (CANH) - K2-14 (CANL) B - W HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) auxiliary battery terminal 54 to 69 Ω
K2-13 (CANH) - K154-4 (CG) B - W-B HIGH-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
K2-14 (CANL) - K154-4 (CG) W - W-B LOW-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
K2-13 (CANH) - K154-16 (BAT) B - R HIGH-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher
K2-14 (CANL) - K154-16 (BAT) W - R LOW-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher




BLIND SPOT MONITOR SENSOR RH (w/ Blind Spot Monitor System)


Refer to Terminals of ECU.

Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>BLIND SPOT MONITOR SYSTEM>TERMINALS OF ECU

a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.

Disconnect the W5 blind spot monitor sensor RH connector.


c.

Measure the resistance according to the value(s) in the table below.

C350884C33
1.688,0.135 2.115,0.427 0.427,0.292 4.979,0.208 5.406,0.5 0.427,0.292 1.76,1.302 1.76,0.615 1.76,0.615 1.604,0.615 true 1.615,2.219 1.76,2.219 1.76,2.219 1.76,1.563 true 2.375,2.219 2.219,2.219 2.219,2.219 2.219,1.563 true 6,2.115 5.844,2.115 5.844,2.115 5.844,1.667 true 0.115,0.073 0.427,0.271 0.313,0.198 10 false *a 3.635,0.073 3.948,0.271 0.313,0.198 10 false *1 1.802,0.208 2.229,0.479 0.427,0.271 10 false W5 5.042,0.292 5.479,0.573 0.438,0.281 10 false K154 1.198,2.156 1.688,2.406 0.49,0.25 10 false CA1N 1.177,0.552 1.667,0.802 0.49,0.25 10 false CA1P 2.448,2.156 2.938,2.406 0.49,0.25 10 false BRGD 6.083,2.052 6.573,2.302 0.49,0.25 10 false BAT
*1 DLC3 - -
*a Front view of wire harness connector
(to Blind Spot Monitor Sensor RH)
- -


Standard Resistance:
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
W5-2 (CA1P) - W5-7 (CA1N) V - W HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) auxiliary battery terminal 54 to 69 Ω
W5-2 (CA1P) - W5-10 (BRGD) V - W-B HIGH-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
W5-7 (CA1N) - W5-10 (BRGD) W - W-B LOW-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
W5-2 (CA1P) - K154-16 (BAT) V - R HIGH-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher
W5-7 (CA1N) - K154-16 (BAT) W - R LOW-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher




FORWARD RECOGNITION CAMERA (w/ Front Camera System)


Refer to Terminals of ECU.

Click hereEngine / Hybrid System>CRUISE CONTROL>FRONT CAMERA SYSTEM>TERMINALS OF ECU

a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.

Disconnect the V6 forward recognition camera connector.


c.

Measure the resistance according to the value(s) in the table below.

C350886C32
1.823,0.146 2.219,0.396 0.396,0.25 4.958,0.208 5.438,0.479 0.479,0.271 2.219,1.688 2.219,2.125 2.219,2.125 2.375,2.125 true 2.219,1.323 2.219,0.583 2.219,0.583 2.375,0.583 true 2.063,1.688 2.063,2.125 2.063,2.125 1.927,2.125 true 5.844,1.677 5.844,2.073 5.844,2.073 6,2.073 true 0.094,0.083 0.406,0.281 0.313,0.198 10 false *a 3.781,0.094 4.094,0.292 0.313,0.198 10 false *1 1.938,0.198 2.323,0.552 0.385,0.354 10 false V6 2.458,0.51 2.927,0.729 0.469,0.219 10 false CA1P 2.458,2.063 2.927,2.281 0.469,0.219 10 false CA1N 1.573,2.063 2.042,2.281 0.469,0.219 10 false GND 5.031,0.26 5.583,0.667 0.552,0.406 10 false K154 6.083,2.01 6.552,2.229 0.469,0.219 10 false BAT
*1 DLC3 - -
*a Front view of wire harness connector
(to Forward Recognition Camera)
- -


Standard Resistance:
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
V6-5 (CA1P) - V6-11 (CA1N) L - W HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) auxiliary battery terminal 54 to 69 Ω
V6-5 (CA1P) - V6-10 (GND) L - LA*1
L - W-B*2
HIGH-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
V6-11 (CA1N) - V6-10 (GND) W - LA*1
W - W-B*2
LOW-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
V6-5 (CA1P) - K154-16 (BAT) L - R HIGH-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher
V6-11 (CA1N) - K154-16 (BAT) W - R LOW-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher


·

*1: through No. 29 Junction Connector

·

*2: not through No. 29 Junction Connector




MILLIMETER WAVE RADAR SENSOR ASSEMBLY (w/ Front Camera System)


Refer to Terminals of ECU.

Click hereEngine / Hybrid System>CRUISE CONTROL>DYNAMIC RADAR CRUISE CONTROL SYSTEM>TERMINALS OF ECU

a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.

Disconnect the A30 millimeter wave radar sensor assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

C350887C34
4.969,0.208 5.5,0.479 0.531,0.271 1.74,0.115 2.167,0.396 0.427,0.281 2.073,1.26 2.073,0.573 2.073,0.573 2.229,0.573 true 1.906,1.26 1.906,0.573 1.906,0.573 1.729,0.573 true 0.99,1.344 1.688,1.344 true 5.979,2.073 5.823,2.073 5.823,2.073 5.833,1.667 true 0.115,0.094 0.427,0.292 0.313,0.198 10 false *a 3.719,0.115 4.031,0.313 0.313,0.198 10 false *1 1.323,0.51 1.802,0.719 0.479,0.208 10 false CA2L 2.354,0.521 2.833,0.729 0.479,0.208 10 false CA2H 0.531,1.281 1.01,1.49 0.479,0.208 10 false SGND 6.094,2.01 6.573,2.219 0.479,0.208 10 false BAT 5.063,0.271 5.625,0.625 0.563,0.354 10 false K154 1.844,0.167 2.167,0.365 0.323,0.198 10 false A30
*1 DLC3 - -
*a Front view of wire harness connector
(to Millimeter Wave Radar Sensor Assembly)
- -


Standard Resistance:
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
A30-3 (CA2H) - A30-2 (CA2L) R - W HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) auxiliary battery terminal 54 to 69 Ω
A30-3 (CA2H) - A30-1 (SGND) R - W-B HIGH-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
A30-2 (CA2L) - A30-1 (SGND) W - W-B LOW-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
A30-3 (CA2H) - K154-16 (BAT) R - R HIGH-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher
A30-2 (CA2L) - K154-16 (BAT) W - R LOW-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher




OCCUPANT DETECTION ECU (w/ Occupant Classification System)


Refer to Terminals of ECU.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>OCCUPANT CLASSIFICATION SYSTEM>TERMINALS OF ECU

a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.

Disconnect the a6 occupant detection ECU connector.


c.

Measure the resistance according to the value(s) in the table below.

C350888C24
1.729,0.115 2.083,0.365 0.354,0.25 5,0.125 5.521,0.427 0.521,0.302 2.219,1.323 2.219,0.573 2.219,0.573 2.354,0.573 true 2.073,1.323 2.073,0.573 2.073,0.573 1.927,0.573 true 2.365,2.219 2.219,2.219 2.219,2.219 2.219,1.552 true 5.99,2.021 5.844,2.021 5.844,2.021 5.844,1.667 true 0.125,0.104 0.438,0.302 0.313,0.198 10 false *a 3.792,0.115 4.104,0.313 0.313,0.198 10 false *1 2.438,0.51 2.979,0.729 0.542,0.219 10 false CANP 1.469,0.51 2.01,0.729 0.542,0.219 10 false CANN 2.448,2.156 2.99,2.375 0.542,0.219 10 false GND 1.833,0.167 2.375,0.385 0.542,0.219 10 false a6 5.094,0.188 5.635,0.406 0.542,0.219 10 false K154 6.083,1.948 6.625,2.167 0.542,0.219 10 false BAT
*1 DLC3 - -
*a Front view of wire harness connector
(to Occupant Detection ECU)
- -


Standard Resistance:
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
a6-5 (CANP) - a6-4 (CANN) R - SB HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) auxiliary battery terminal 54 to 69 Ω
a6-5 (CANP) - a6-10 (GND) R - W-B HIGH-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
a6-4 (CANN) - a6-10 (GND) SB - W-B LOW-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
a6-5 (CANP) - K154-16 (BAT) R - R HIGH-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher
a6-4 (CANN) - K154-16 (BAT) SB - R LOW-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher




REAR TELEVISION CAMERA ASSEMBLY (w/ Parking Assist Monitor System)


Refer to Terminals of ECU.

Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>PARKING ASSIST MONITOR SYSTEM>TERMINALS OF ECU

a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.

Disconnect the m3 rear television camera assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

C350889C12
1.865,0.146 2.188,0.365 0.323,0.219 5.021,0.135 5.51,0.406 0.49,0.271 1.885,1.292 1.885,0.51 1.885,0.51 1.708,0.51 true 1.719,2.281 1.875,2.281 1.875,2.281 1.875,1.698 true 5.125,1.115 5.125,0.635 5.125,0.635 4.948,0.635 true 6,2.156 5.833,2.156 5.833,2.156 5.833,1.667 true 0.073,0.052 0.385,0.25 0.313,0.198 10 false *a 1.938,0.188 2.365,0.458 0.427,0.271 10 false m3 1.25,2.229 1.833,2.458 0.583,0.229 10 false CANH 1.281,0.458 1.865,0.688 0.583,0.229 10 false CANL 5.104,0.188 5.604,0.542 0.5,0.354 10 false K154 4.667,0.583 5.25,0.813 0.583,0.229 10 false CG 6.115,2.083 6.698,2.313 0.583,0.229 10 false BAT 3.771,0.073 4.083,0.271 0.313,0.198 10 false *1
*1 DLC3 - -
*a Front view of wire harness connector
(to Rear Television Camera Assembly)
- -


Standard Resistance:
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
m3-4 (CANH) - m3-1 (CANL) R - W HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) auxiliary battery terminal 54 to 69 Ω
m3-4 (CANH) - K154-4 (CG) R - W-B HIGH-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
m3-1 (CANL) - K154-4 (CG) W - W-B LOW-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
m3-4 (CANH) - K154-16 (BAT) R - R HIGH-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher
m3-1 (CANL) - K154-16 (BAT) W - R LOW-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher




REAR TELEVISION CAMERA ASSEMBLY (w/ Panoramic View Monitor System)


Refer to Terminals of ECU.

Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>PANORAMIC VIEW MONITOR SYSTEM>TERMINALS OF ECU

a.

Disconnect the cable from the negative (-) battery terminal.


b.

Disconnect the m4 rear television camera assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

C376295C19
1.854,0.115 2.219,0.396 0.365,0.281 5.323,0.188 5.74,0.427 0.417,0.24 5.188,1.115 5.188,0.667 5.188,0.667 5.021,0.667 true 6.063,2.104 5.896,2.104 5.896,2.104 5.896,1.688 true 1.802,1.281 1.802,0.51 1.802,0.51 1.635,0.51 true 1.792,1.677 1.792,2.302 1.792,2.302 1.625,2.302 true 0.104,0.083 0.417,0.281 0.313,0.198 10 false *a 3.771,0.115 4.083,0.313 0.313,0.198 10 false *1 1.948,0.177 2.26,0.375 0.313,0.198 10 false m4 5.375,0.229 5.927,0.479 0.552,0.25 10 false K154 1.198,0.448 1.667,0.698 0.469,0.25 10 false CANL 1.167,2.24 1.635,2.49 0.469,0.25 10 false CANH 4.74,0.604 5.104,0.854 0.365,0.25 10 false CG 6.156,2.042 6.521,2.292 0.365,0.25 10 false BAT
*1 DLC3 - -
*a Front view of wire harness connector
(to Rear Television Camera Assembly)
- -


Standard Resistance:
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
m4-4 (CANH) - m4-1 (CANL) R - W HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) auxiliary battery terminal 54 to 69 Ω
m4-4 (CANH) - K154-4 (CG) R - W-B HIGH-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
m4-1 (CANL) - K154-4 (CG) W - W-B LOW-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
m4-4 (CANH) - K154-16 (BAT) R - R HIGH-level CAN bus line - Battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher
m4-1 (CANL) - K154-16 (BAT) W - R LOW-level CAN bus line - Battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher




TIRE PRESSURE WARNING ECU AND RECEIVER (w/ Tire Pressure Warning System and Tire Inflation Pressure Display Function)


Refer to Terminals of ECU.

Click hereSuspension>TIRE PRESSURE MONITORING>TIRE PRESSURE WARNING SYSTEM>TERMINALS OF ECU

a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.

Disconnect the R9 tire pressure warning ECU and receiver connector.


c.
C346239C24
1.5,0.823 1.917,1.083 0.417,0.26 1.167,2.531 1.333,2.531 1.333,2.531 1.333,2.115 true 2.313,2.531 2.146,2.531 2.146,2.531 2.146,2.115 true 1.99,2.854 1.823,2.854 1.823,2.854 1.823,2.094 true 1.458,2.854 1.646,2.854 1.646,2.854 1.646,2.094 true 0.115,0.063 0.427,0.26 0.313,0.198 10 false *a 1.625,0.885 2.083,1.083 0.458,0.198 10 false R9 0.917,2.458 1.188,2.667 0.271,0.208 10 false +B 2.385,2.448 2.813,2.667 0.427,0.219 10 false GND 2.073,2.792 2.594,3.052 0.521,0.26 10 false CANL 1,2.792 1.521,3.052 0.521,0.26 10 false CANH
*a Front view of wire harness connector
(to Tire Pressure Warning ECU and Receiver)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
R9-9 (CANH) - R9-10 (CANL) L - W HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) auxiliary battery terminal 54 to 69 Ω
R9-9 (CANH) - R9-12 (GND) L - W-B HIGH-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
R9-10 (CANL) - R9-12 (GND) W - W-B LOW-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
R9-9 (CANH) - R9-7 (+B) L - LA-R HIGH-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher
R9-10 (CANL) - R9-7 (+B) W - LA-R LOW-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher




BRAKE ACTUATOR ASSEMBLY


Refer to Terminals of ECU.

Click hereBrake>PARKING BRAKE>ELECTRIC PARKING BRAKE SYSTEM>TERMINALS OF ECU

a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.

Disconnect the A44 brake actuator assembly connector.


c.
C378945C03
1.615,0.417 2,0.656 0.385,0.24 1.823,2.802 1.656,2.802 1.656,2.802 1.656,1.802 true 1.365,2.802 1.531,2.802 1.531,2.802 1.531,1.802 true 2.771,0.76 2.604,0.76 2.604,0.76 2.604,1.51 true 0.75,0.75 0.917,0.75 0.917,0.75 0.917,1.5 true 0.125,0.094 0.438,0.292 0.313,0.198 10 false *a 1.688,0.469 2,0.667 0.313,0.198 10 false A44 1.938,2.74 2.417,2.969 0.479,0.229 10 false CANH 0.969,2.75 1.448,2.979 0.479,0.229 10 false CANL 2.844,0.677 3.323,0.906 0.479,0.229 10 false BEPB 0.302,0.677 0.781,0.906 0.479,0.229 10 false MGND
*a Front view of wire harness connector
(to Brake Actuator Assembly)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
A44-12 (CANH) - A44-11 (CANL) B - W HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) auxiliary battery terminal 54 to 69 Ω
A44-12 (CANH) - A44-1 (MGND) B - W-B HIGH-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
A44-11 (CANL) - A44-1 (MGND) W - W-B LOW-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
A44-12 (CANH) - A44-9 (BEPB) B - R HIGH-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher
A44-11 (CANL) - A44-9 (BEPB) W - R LOW-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher




METER MIRROR SUB-ASSEMBLY (w/ Headup Display System)


Refer to Terminals of ECU.

Click hereVehicle Interior>METER / GAUGE / DISPLAY>HEADUP DISPLAY SYSTEM>TERMINALS OF ECU

a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.

Disconnect the p1 meter mirror sub-assembly connector.


c.
C378909C03
1.479,0.281 1.917,0.552 0.438,0.271 1.865,2.656 2.031,2.656 2.031,2.656 2.031,1.99 true 2.354,2.656 2.188,2.656 2.188,2.656 2.188,1.99 true 2.563,0.875 2.729,0.875 2.729,0.875 2.729,1.625 true 1.167,0.896 1,0.896 1,0.896 1,1.646 true 0.146,0.104 0.458,0.302 0.313,0.198 10 false *a 1.635,0.354 1.948,0.552 0.313,0.198 10 false p1 1.458,2.594 2.094,2.875 0.635,0.281 10 false MPX1 2.458,2.594 3.094,2.875 0.635,0.281 10 false MPX2 2.323,0.823 2.958,1.104 0.635,0.281 10 false ES 1.281,0.823 1.698,1.021 0.417,0.198 10 false B
*a Front view of wire harness connector
(to Meter Mirror Sub-assembly)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
p1-12 (MPX1) - p1-13 (MPX2) P - R HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) auxiliary battery terminal 54 to 69 Ω
p1-12 (MPX1) - p1-4 (ES) P - W-B HIGH-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
p1-13 (MPX2) - p1-4 (ES) R - W-B LOW-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
p1-12 (MPX1) - p1-2 (B) P - P HIGH-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher
p1-13 (MPX2) - p1-2 (B) R - P LOW-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher




HEADLIGHT ECU SUB-ASSEMBLY LH (w/ Automatic Headlight Beam Level Control System)


Refer to Terminals of ECU.

Click hereVehicle Exterior>LIGHTING (EXT)>LIGHTING SYSTEM (w/ Automatic Headlight Beam Level Control System)>TERMINALS OF ECU

a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.

Disconnect the A78 headlight ECU sub-assembly LH connector.


c.

Measure the resistance according to the value(s) in the table below.

C366205C51
1.594,0.417 2.094,0.667 0.5,0.25 5.25,0.583 5.75,0.833 0.5,0.25 6.281,2.208 6.115,2.208 6.115,2.208 6.115,1.729 true 2.948,2.26 2.781,2.26 2.781,2.26 2.781,1.677 true 2.49,2.26 2.656,2.26 2.656,2.26 2.656,1.677 true 1.104,2.24 0.938,2.24 0.938,2.24 0.938,1.656 true 0.146,0.24 0.458,0.438 0.313,0.198 10 false *a 1.719,0.469 2.115,0.719 0.396,0.25 10 false A78 5.344,0.615 5.813,0.854 0.469,0.24 10 false K154 1.177,2.167 1.573,2.333 0.396,0.167 10 false GND 2.094,2.198 2.656,2.365 0.563,0.167 10 false CANL 3.042,2.177 3.604,2.344 0.563,0.167 10 false CANH 6.333,2.115 6.833,2.333 0.5,0.219 10 false BAT 3.938,0.417 4.25,0.615 0.313,0.198 10 false *1
*1 DLC3 - -
*a Front view of wire harness connector
(to Headlight ECU Sub-assembly LH)
- -


Standard Resistance:
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
A78-24(CANH) - A78-23(CANL) W - L HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) auxiliary battery terminal 54 to 69 Ω
A78-24(CANH) - A78-12 (GND) W - W-B HIGH-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
A78-23(CANL) - A78-12 (GND) L - W-B LOW-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
A78-24(CANH) - K154-16 (BAT) W - R HIGH-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher
A78-23(CANL) - K154-16 (BAT) L - R LOW-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher




HEADLIGHT ECU SUB-ASSEMBLY RH (w/ Automatic Headlight Beam Level Control System)


Refer to Terminals of ECU.

Click hereVehicle Exterior>LIGHTING (EXT)>LIGHTING SYSTEM (w/ Automatic Headlight Beam Level Control System)>TERMINALS OF ECU

a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.

Disconnect the A79 headlight ECU sub-assembly RH connector.


c.

Measure the resistance according to the value(s) in the table below.

C366205C54
1.594,0.417 2.094,0.667 0.5,0.25 5.25,0.583 5.75,0.833 0.5,0.25 6.281,2.208 6.115,2.208 6.115,2.208 6.115,1.729 true 2.948,2.26 2.781,2.26 2.781,2.26 2.781,1.677 true 2.49,2.26 2.656,2.26 2.656,2.26 2.656,1.677 true 1.104,2.24 0.938,2.24 0.938,2.24 0.938,1.656 true 0.281,0.313 0.594,0.51 0.313,0.198 10 false *a 1.729,0.469 2.188,0.813 0.458,0.344 10 false A79 5.344,0.625 5.802,0.906 0.458,0.281 10 false K154 1.177,2.167 1.573,2.333 0.396,0.167 10 false GND 2.094,2.198 2.656,2.365 0.563,0.167 10 false CANL 3.042,2.177 3.604,2.344 0.563,0.167 10 false CANH 6.333,2.115 6.833,2.333 0.5,0.219 10 false BAT 4.073,0.365 4.385,0.563 0.313,0.198 10 false *1
*1 DLC3 - -
*a Front view of wire harness connector
(to Headlight ECU Sub-assembly RH)
- -


Standard Resistance:
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
A79-24 (CANH) - A79-23 (CANL) L - W HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) auxiliary battery terminal 54 to 69 Ω
A79-24 (CANH) - A79-12 (GND) L - W-B HIGH-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
A79-23 (CANL) - A79-12 (GND) W - W-B LOW-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
A79-24 (CANH) - K154-16 (BAT) L - R HIGH-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher
A79-23 (CANL) - K154-16 (BAT) W - R LOW-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher




CLEARANCE WARNING ECU ASSEMBLY (w/o Parking Support Brake System)


Refer to Terminals of ECU.

Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>TOYOTA PARKING ASSIST-SENSOR SYSTEM (w/o Parking Support Brake System)>TERMINALS OF ECU

a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.

Disconnect the R39 clearance warning ECU assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

C350879C16
1.688,0.188 2.104,0.458 0.417,0.271 5.063,0.188 5.594,0.458 0.531,0.271 3.052,1.25 3.052,0.729 3.052,0.729 3.188,0.729 true 2.042,2.052 1.906,2.052 1.906,2.052 1.906,1.469 true 6.063,2.104 5.927,2.104 5.927,2.104 5.927,1.677 true 2.938,1.25 2.938,0.75 2.938,0.75 2.771,0.75 true 0.115,0.094 0.427,0.292 0.313,0.198 10 false *a 3.917,0.115 4.229,0.313 0.313,0.198 10 false *1 2.531,0.677 2.844,0.875 0.313,0.198 10 false R1 3.281,0.677 3.594,0.875 0.313,0.198 10 false R2 1.771,0.24 2.156,0.51 0.385,0.271 10 false R39 2.146,1.969 2.458,2.167 0.313,0.198 10 false E 6.135,2.031 6.656,2.24 0.521,0.208 10 false BAT 5.167,0.24 5.552,0.51 0.385,0.271 10 false K154
*1 DLC3 - -
*a Front view of wire harness connector
(to Clearance Warning ECU Assembly)
- -


Standard Resistance:
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
R39-17 (R1) - R39-18 (R2) L - W HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) auxiliary battery terminal 54 to 69 Ω
R39-17 (R1) - R39-30 (E) L - W-B HIGH-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
R39-18 (R2) - R39-30 (E) W - W-B LOW-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
R39-17 (R1) - K154-16 (BAT) L - R HIGH-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher
R39-18 (R2) - K154-16 (BAT) W - R LOW-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher




CLEARANCE WARNING ECU ASSEMBLY (w/ Parking Support Brake System)


Refer to Terminals of ECU.

Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>PARKING SUPPORT BRAKE SYSTEM>TERMINALS OF ECU

a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.

Disconnect the R39 clearance warning ECU assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

C381732C16
1.615,0.156 2.042,0.427 0.427,0.271 4.948,0.365 5.375,0.635 0.427,0.271 5.938,1.667 5.938,2.167 5.938,2.167 6.104,2.167 true 2,1.458 2,1.958 2,1.958 2.167,1.958 true 2.896,0.427 3.063,0.427 3.063,0.427 3.063,1.26 true 2.76,0.677 2.927,0.677 2.927,0.677 2.927,1.26 true 0.125,0.094 0.438,0.292 0.313,0.198 10 false *a 1.719,0.219 2.031,0.417 0.313,0.198 10 false R39 2.49,0.594 2.802,0.792 0.313,0.198 10 false R1 2.646,0.354 2.958,0.552 0.313,0.198 10 false R2 4,0.115 4.313,0.313 0.313,0.198 10 false *1 5.01,0.427 5.552,0.656 0.542,0.229 10 false K154 6.198,2.083 6.51,2.281 0.313,0.198 10 false BAT 2.229,1.885 2.542,2.083 0.313,0.198 10 false E
*1 DLC3 - -
*a Front view of wire harness connector
(to Clearance Warning ECU Assembly)
- -


Standard Resistance:
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
R39-17 (R1) - R39-18 (R2) L - W HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) auxiliary battery terminal 54 to 69 Ω
R39-17 (R1) - R39-31 (E) L - W-B HIGH-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
R39-18 (R2) - R39-31 (E) W - W-B LOW-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
R39-17 (R1) - K154-16 (BAT) L - R HIGH-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher
R39-18 (R2) - K154-16 (BAT) W - R LOW-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher




MULTIPLEX TILT AND TELESCOPIC ECU (w/ Power Tilt and Power Telescopic System)


Refer to Terminals of ECU.

Click hereSteering>STEERING COLUMN>POWER TILT AND POWER TELESCOPIC STEERING COLUMN SYSTEM>TERMINALS OF ECU

a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.

Disconnect the K72 multiplex tilt and telescopic ECU connector.


c.
C381596C07
1.438,0.323 1.875,0.604 0.438,0.281 1.25,1.583 1.25,0.833 1.25,0.833 1.417,0.833 true 1.25,1.917 1.25,2.667 1.25,2.667 1.417,2.667 true 0.906,1.583 0.906,0.833 0.906,0.833 0.75,0.833 true 0.688,1.583 0.688,1.073 0.688,1.073 0.521,1.073 true 0.135,0.125 0.448,0.323 0.313,0.198 10 false *a 1.552,0.385 1.99,0.656 0.438,0.271 10 false K72 1.51,0.75 1.948,1.021 0.438,0.271 10 false CANP 1.5,2.583 1.938,2.854 0.438,0.271 10 false CANN 0.5,0.76 0.938,1.031 0.438,0.271 10 false +B 0.156,1 0.594,1.271 0.438,0.271 10 false GND
*a Front view of wire harness connector
(to Multiplex Tilt and Telescopic ECU)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
K72-3 (CANP) - K72-11 (CANN) R - W HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) auxiliary battery terminal 54 to 69 Ω
K72-3 (CANP) - K72-1 (GND) R - W-B*1
R - LA*2
HIGH-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
K72-11 (CANN) - K72-1 (GND) W - W-B*1
W - LA*2
LOW-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
K72-3 (CANP) - K72-2 (+B) R - B*1
R - LA-B*2
HIGH-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher
K72-11 (CANN) - K72-2 (+B) W - B*1
W - LA-B*2
LOW-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher


·

*1: for LHD

·

*2: for RHD




POSITION CONTROL ECU ASSEMBLY LH (for LHD with Seat Position Memory System)


Refer to Terminals of ECU.

Click hereVehicle Interior>SEAT>FRONT POWER SEAT CONTROL SYSTEM (w/ Memory)>TERMINALS OF ECU

a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.

Disconnect the b10 and b22 position control ECU assembly LH connectors.


c.

Measure the resistance according to the value(s) in the table below.

C381597C10
1.76,0.219 2.188,0.479 0.427,0.26 4.927,0.219 5.354,0.479 0.427,0.26 2.667,1.333 2.667,0.5 2.667,0.5 2.833,0.5 true 2.792,1.333 2.792,0.75 2.792,0.75 2.958,0.75 true 5.417,1.292 5.417,0.792 5.417,0.792 5.583,0.792 true 4.948,1.292 4.948,0.792 4.948,0.792 4.781,0.792 true 1.865,0.271 2.323,0.469 0.458,0.198 10 false b22 5.021,0.26 5.479,0.458 0.458,0.198 10 false b10 0.167,0.094 0.625,0.292 0.458,0.198 10 false *a 2.927,0.417 3.427,0.667 0.5,0.25 10 false CANP 3.042,0.677 3.542,0.927 0.5,0.25 10 false CANN 5.688,0.708 6.188,0.958 0.5,0.25 10 false +B 4.396,0.719 4.896,0.969 0.5,0.25 10 false GND
*a Front view of wire harness connector
(to Position Control ECU Assembly LH)
- -


Standard Resistance:
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
b22-13 (CANP) - b22-14 (CANN) LG - R HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) auxiliary battery terminal 54 to 69 Ω
b22-13 (CANP) - b10-2 (GND) LG - W-B HIGH-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
b22-14 (CANN) - b10-2 (GND) R - W-B LOW-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
b22-13 (CANP) - b10-3 (+B) LG - W HIGH-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher
b22-14 (CANN) - b10-3 (+B) R - W LOW-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher




POSITION CONTROL ECU ASSEMBLY RH (for RHD with Seat Position Memory System)


Refer to Terminals of ECU.

Click hereVehicle Interior>SEAT>FRONT POWER SEAT CONTROL SYSTEM (w/ Memory)>TERMINALS OF ECU

a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.

Disconnect the a29 and a31 position control ECU assembly RH connectors.


c.

Measure the resistance according to the value(s) in the table below.

C381597C05
1.76,0.219 2.188,0.479 0.427,0.26 4.927,0.219 5.354,0.479 0.427,0.26 2.667,1.333 2.667,0.5 2.667,0.5 2.833,0.5 true 2.792,1.333 2.792,0.75 2.792,0.75 2.958,0.75 true 5.417,1.292 5.417,0.792 5.417,0.792 5.583,0.792 true 4.948,1.292 4.948,0.792 4.948,0.792 4.781,0.792 true 1.865,0.271 2.323,0.469 0.458,0.198 10 false a31 5.021,0.26 5.479,0.458 0.458,0.198 10 false a29 0.167,0.094 0.625,0.292 0.458,0.198 10 false *a 2.927,0.417 3.427,0.667 0.5,0.25 10 false CANP 3.042,0.677 3.542,0.927 0.5,0.25 10 false CANN 5.688,0.708 6.188,0.958 0.5,0.25 10 false +B 4.396,0.719 4.896,0.969 0.5,0.25 10 false GND
*a Front view of wire harness connector
(to Position Control ECU Assembly RH)
- -


Standard Resistance:
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
a31-13 (CANP) - a31-14 (CANN) LG - R HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) auxiliary battery terminal 54 to 69 Ω
a31-13 (CANP) - a29-2 (GND) LG - W-B HIGH-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
a31-14 (CANN) - a29-2 (GND) R - W-B LOW-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
a31-13 (CANP) - a29-3 (+B) LG - W HIGH-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher
a31-14 (CANN) - a29-3 (+B) R - W LOW-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher




OUTER MIRROR CONTROL ECU ASSEMBLY (FOR DRIVER SIDE) (for LHD with Seat Position Memory System)


Refer to Terminals of ECU.

Click hereVehicle Exterior>MIRROR (EXT)>POWER MIRROR CONTROL SYSTEM (w/ Memory)>TERMINALS OF ECU

a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.

Disconnect the O8 outer mirror control ECU assembly (for driver side) connector.


c.
C381598C46
1.427,0.323 1.854,0.594 0.427,0.271 1.167,2.083 1.167,3 1.167,3 1.333,3 true 1.333,2.083 1.333,2.667 1.333,2.667 1.5,2.667 true 2.229,1.656 2.229,0.906 2.229,0.906 2.396,0.906 true 2.01,1.698 2.01,0.677 2.01,0.677 2.177,0.677 true 0.115,0.094 0.427,0.292 0.313,0.198 10 false *a 1.563,0.375 1.948,0.635 0.385,0.26 10 false O8 1.594,2.583 2.073,2.823 0.479,0.24 10 false CANP 1.417,2.927 1.896,3.167 0.479,0.24 10 false CANN 2.271,0.594 2.75,0.833 0.479,0.24 10 false CPUB 2.479,0.823 2.958,1.063 0.479,0.24 10 false GND
*a Front view of wire harness connector
(to Outer Mirror Control ECU Assembly (for Driver Side))


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
O8-9 (CANP) - O8-8 (CANN) P - W HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) auxiliary battery terminal 54 to 69 Ω
O8-9 (CANP) - O8-7 (GND) P - W-B HIGH-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
O8-8 (CANN) - O8-7 (GND) W - W-B LOW-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
O8-9 (CANP) - O8-6 (CPUB) P - LA-L HIGH-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher
O8-8 (CANN) - O8-6 (CPUB) W - LA-L LOW-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher




OUTER MIRROR CONTROL ECU ASSEMBLY (FOR DRIVER SIDE) (for RHD with Seat Position Memory System)


Refer to Terminals of ECU.

Click hereVehicle Exterior>MIRROR (EXT)>POWER MIRROR CONTROL SYSTEM (w/ Memory)>TERMINALS OF ECU

a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.

Disconnect the N9 outer mirror control ECU assembly (for driver side) connector.


c.
C381598C08
1.427,0.323 1.854,0.594 0.427,0.271 1.167,2.083 1.167,3 1.167,3 1.333,3 true 1.333,2.083 1.333,2.667 1.333,2.667 1.5,2.667 true 2.229,1.656 2.229,0.906 2.229,0.906 2.396,0.906 true 2.01,1.698 2.01,0.677 2.01,0.677 2.177,0.677 true 0.115,0.094 0.427,0.292 0.313,0.198 10 false *a 1.552,0.385 1.938,0.646 0.385,0.26 10 false N9 1.594,2.583 2.073,2.823 0.479,0.24 10 false CANP 1.417,2.927 1.896,3.167 0.479,0.24 10 false CANN 2.271,0.594 2.75,0.833 0.479,0.24 10 false CPUB 2.479,0.823 2.958,1.063 0.479,0.24 10 false GND
*a Front view of wire harness connector
(to Outer Mirror Control ECU Assembly (for Driver Side))


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
N9-9 (CANP) - N9-8 (CANN) P - W HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) auxiliary battery terminal 54 to 69 Ω
N9-9 (CANP) - N9-7 (GND) P - W-B HIGH-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
N9-8 (CANN) - N9-7 (GND) W - W-B LOW-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
N9-9 (CANP) - N9-6 (CPUB) P - LA-L HIGH-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher
N9-8 (CANN) - N9-6 (CPUB) W - LA-L LOW-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher




OUTER MIRROR CONTROL ECU ASSEMBLY (FOR FRONT PASSENGER SIDE) (for LHD with Seat Position Memory System)


Refer to Terminals of ECU.

Click hereVehicle Exterior>MIRROR (EXT)>POWER MIRROR CONTROL SYSTEM (w/ Memory)>TERMINALS OF ECU

a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.

Disconnect the N9 outer mirror control ECU assembly (for front passenger side) connector.


c.
C381598C47
1.427,0.323 1.854,0.594 0.427,0.271 1.167,2.083 1.167,3 1.167,3 1.333,3 true 1.333,2.083 1.333,2.667 1.333,2.667 1.5,2.667 true 2.229,1.656 2.229,0.906 2.229,0.906 2.396,0.906 true 2.01,1.698 2.01,0.677 2.01,0.677 2.177,0.677 true 0.115,0.094 0.427,0.292 0.313,0.198 10 false *a 1.573,0.385 1.958,0.646 0.385,0.26 10 false N9 1.594,2.583 2.073,2.823 0.479,0.24 10 false CANP 1.417,2.927 1.896,3.167 0.479,0.24 10 false CANN 2.271,0.594 2.75,0.833 0.479,0.24 10 false CPUB 2.479,0.823 2.958,1.063 0.479,0.24 10 false GND
*a Front view of wire harness connector
(to Outer Mirror Control ECU Assembly (for Front Passenger Side))


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
N9-9 (CANP) - N9-8 (CANN) P - W HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) auxiliary battery terminal 54 to 69 Ω
N9-9 (CANP) - N9-7 (GND) P - W-B HIGH-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
N9-8 (CANN) - N9-7 (GND) W - W-B LOW-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
N9-9 (CANP) - N9-6 (CPUB) P - LA-L HIGH-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher
N9-8 (CANN) - N9-6 (CPUB) W - LA-L LOW-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher




OUTER MIRROR CONTROL ECU ASSEMBLY (FOR FRONT PASSENGER SIDE) (for RHD with Seat Position Memory System)


Refer to Terminals of ECU.

Click hereVehicle Exterior>MIRROR (EXT)>POWER MIRROR CONTROL SYSTEM (w/ Memory)>TERMINALS OF ECU

a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.

Disconnect the O8 outer mirror control ECU assembly (for front passenger side) connector.


c.
C381598C09
1.427,0.323 1.854,0.594 0.427,0.271 1.167,2.083 1.167,3 1.167,3 1.333,3 true 1.333,2.083 1.333,2.667 1.333,2.667 1.5,2.667 true 2.229,1.656 2.229,0.906 2.229,0.906 2.396,0.906 true 2.01,1.698 2.01,0.677 2.01,0.677 2.177,0.677 true 0.115,0.094 0.427,0.292 0.313,0.198 10 false *a 1.542,0.385 1.927,0.646 0.385,0.26 10 false O8 1.594,2.583 2.073,2.823 0.479,0.24 10 false CANP 1.417,2.927 1.896,3.167 0.479,0.24 10 false CANN 2.271,0.594 2.75,0.833 0.479,0.24 10 false CPUB 2.479,0.823 2.958,1.063 0.479,0.24 10 false GND
*a Front view of wire harness connector
(to Outer Mirror Control ECU Assembly (for Front Passenger Side))


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
O8-9 (CANP) - O8-8 (CANN) P - W HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) auxiliary battery terminal 54 to 69 Ω
O8-9 (CANP) - O8-7 (GND) P - W-B HIGH-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
O8-8 (CANN) - O8-7 (GND) W - W-B LOW-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
O8-9 (CANP) - O8-6 (CPUB) P - LA-L HIGH-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher
O8-8 (CANN) - O8-6 (CPUB) W - LA-L LOW-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher




OPTION CONNECTOR (BUS BUFFER ECU)


a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.

Disconnect the K143 option connector (bus buffer ECU).

HINT:

Disconnect any CAN compatible optional devices from the option connector.



c.
C392362C04
1.469,0.333 1.948,0.604 0.479,0.271 1.979,1.823 1.979,0.99 1.979,0.99 2.146,0.99 true 1.635,1.823 1.635,0.99 1.635,0.99 1.469,0.99 true 1.979,2.156 1.979,2.906 1.979,2.906 2.146,2.906 true 1.802,1.813 1.802,0.781 1.802,0.781 1.969,0.781 true 0.104,0.073 0.417,0.271 0.313,0.198 10 false *a 1.563,0.396 1.979,0.646 0.417,0.25 10 false K143 1.125,0.917 1.635,1.198 0.51,0.281 10 false R+B 2.052,0.698 2.563,0.979 0.51,0.281 10 false CAN+ 2.229,0.906 2.74,1.188 0.51,0.281 10 false CAN- 2.229,2.823 2.74,3.104 0.51,0.281 10 false GND
*a Front view of wire harness connector
(to Option Connector (Bus Buffer ECU))


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
K143-2 (CAN+) - K143-1 (CAN-) LG - W HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) auxiliary battery terminal 54 to 69 Ω
K143-2 (CAN+) - K143-5 (GND) LG - W-B HIGH-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
K143-1 (CAN-) - K143-5 (GND) W - W-B LOW-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
K143-2 (CAN+) - K143-3 (R+B) LG - B HIGH-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher
K143-1 (CAN-) - K143-3 (R+B) W - B LOW-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher




TELEMATICS TRANSCEIVER (w/ Telematics Transceiver)


Refer to Terminals of ECU.


a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.

Disconnect the K151 telematics transceiver connector.


c.
C449820C04
1.469,0.167 1.979,0.469 0.51,0.302 0.344,1.635 0.344,0.885 0.344,0.885 0.5,0.885 true 1.333,1.875 1.333,2.615 1.333,2.615 1.5,2.615 true 0.552,1.875 0.552,2.615 0.552,2.615 0.719,2.615 true 1.208,1.885 1.208,2.792 1.208,2.792 1.375,2.792 true 1.573,0.229 2.031,0.427 0.458,0.198 10 false K151 1.583,2.521 2.281,2.792 0.698,0.271 10 false CANN 1.438,2.708 2.135,2.979 0.698,0.271 10 false CANP 0.125,0.063 0.583,0.26 0.458,0.198 10 false *a 0.583,0.813 1.281,1.083 0.698,0.271 10 false +B 0.792,2.531 1.49,2.802 0.698,0.271 10 false E
*a Front view of wire harness connector
(to Telematics Transceiver)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
K151-25 (CANP) - K151-26 (CANN) R - W HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) auxiliary battery terminal 54 to 69 Ω
K151-25 (CANP) - K151-20 (E) R - W-B HIGH-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
K151-26 (CANN) - K151-20 (E) W - W-B LOW-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
K151-25 (CANP) - K151-1 (+B) R - B HIGH-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher
K151-26 (CANN) - K151-1 (+B) W - B LOW-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher




BATTERY ECU ASSEMBLY (for Lithium-ion Battery)


Refer to Terminals of ECU.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM (for LITHIUM-ION BATTERY)>TERMINALS OF ECU

a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.

Disconnect the z16 battery ECU assembly connector.


c.
C378946C16
1.521,0.063 1.896,0.281 0.375,0.219 1.25,3.031 1.417,3.031 1.417,3.031 1.417,2.198 true 1.698,3.031 1.531,3.031 1.531,3.031 1.531,2.198 true 0.573,0.635 0.74,0.635 0.74,0.635 1.063,1.906 true 0.677,0.385 0.844,0.385 0.844,0.385 1.281,1.906 true 1.583,0.094 2.042,0.292 0.458,0.198 10 false z16 0.146,0.094 0.604,0.292 0.458,0.198 10 false *a 1.781,2.958 2.417,3.198 0.635,0.24 10 false CA2H 0.875,2.979 1.51,3.219 0.635,0.24 10 false CA2L 0.302,0.583 0.688,0.792 0.385,0.208 10 false AM 0.229,0.302 0.698,0.552 0.469,0.25 10 false GND1
*a Front view of wire harness connector
(to Battery ECU Assembly)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
z16-29 (CA2H) - z16-28 (CA2L) R - W HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) auxiliary battery terminal 54 to 69 Ω
z16-29 (CA2H) - z16-3 (GND1) R - GR HIGH-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
z16-28 (CA2L) - z16-3 (GND1) W - GR LOW-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
z16-29 (CA2H) - z16-1 (AM) R - BR HIGH-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher
z16-28 (CA2L) - z16-1 (AM) W - BR LOW-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher




VEHICLE APPROACHING SPEAKER CONTROLLER (w/ Vehicle Proximity Notification System)


Refer to Terminals of ECU.

Click hereVehicle Exterior>VEHICLE PROXIMITY NOTIFICATION SYSTEM>VEHICLE PROXIMITY NOTIFICATION SYSTEM (w/o Vehicle Approaching Speaker Switch)>TERMINALS OF ECU

a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.

Disconnect the K161 vehicle approaching speaker controller connector.


c.

Measure the resistance according to the value(s) in the table below.

C398277C42
4.99,0.281 5.438,0.51 0.448,0.229 1.865,0.344 2.313,0.573 0.448,0.229 1.688,2 1.854,2 1.854,2 1.854,1.583 true 2.438,2.01 2.271,2.01 2.271,2.01 2.271,1.594 true 1.833,2.25 2,2.25 2,2.25 2,1.583 true 6,2.083 5.833,2.083 5.833,2.083 5.833,1.667 true 3.552,0.292 3.865,0.49 0.313,0.198 10 false *1 0.958,0.313 1.271,0.51 0.313,0.198 10 false *a 1.958,0.375 2.552,0.635 0.594,0.26 10 false K161 5.083,0.323 5.469,0.573 0.385,0.25 10 false K154 2.5,1.927 3.115,2.167 0.615,0.24 10 false GND 1.25,1.927 1.781,2.167 0.531,0.24 10 false CANH 1.427,2.167 1.958,2.406 0.531,0.24 10 false CANL 6.052,2 6.583,2.24 0.531,0.24 10 false BAT
*1 DLC3 - -
*a Front view of wire harness connector
(to Vehicle Approaching Speaker Controller)
- -


Standard Resistance:
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
K161-3 (CANH) - K161-4 (CANL) Y - W HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) auxiliary battery terminal 54 to 69 Ω
K161-3 (CANH) - K161-6 (GND) Y - W-B HIGH-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
K161-4 (CANL) - K161-6 (GND) W - W-B LOW-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
K161-3 (CANH) - K154-16 (BAT) Y - R HIGH-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher
K161-4 (CANL) - K154-16 (BAT) W - R LOW-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher




TELEVISION CAMERA CONTROLLER (w/ Panoramic View Monitor System)


Refer to Terminals of ECU.

Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>PANORAMIC VIEW MONITOR SYSTEM>TERMINALS OF ECU

a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.

Disconnect the R125 television camera controller connector.


c.
C448923C08
1.5,0.167 1.917,0.417 0.417,0.25 1.708,2.677 1.875,2.677 1.875,2.677 1.875,2.094 true 2.208,2.677 2.042,2.677 2.042,2.677 2.042,2.094 true 0.813,0.813 0.646,0.813 0.646,0.813 0.646,1.729 true 2.604,0.813 2.771,0.813 2.771,0.813 2.771,1.729 true 0.219,0.188 0.531,0.385 0.313,0.198 10 false *a 1.542,0.208 1.948,0.438 0.406,0.229 10 false R125 1.302,2.625 1.781,2.833 0.479,0.208 10 false CANH 2.271,2.615 2.75,2.823 0.479,0.208 10 false CANL 0.948,0.729 1.271,0.958 0.323,0.229 10 false +B 2.156,0.74 2.656,0.99 0.5,0.25 10 false GND1
*a Front view of wire harness connector
(to Television Camera Controller)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
R125-11 (CANH) - R125-12 (CANL) GR - W HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) auxiliary battery terminal 54 to 69 Ω
R125-11 (CANH) - R125-4 (GND1) GR - W-B HIGH-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
R125-12 (CANL) - R125-4 (GND1) W - W-B LOW-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
R125-11 (CANH) - R125-1 (+B) GR - R HIGH-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher
R125-12 (CANL) - R125-1 (+B) W - R LOW-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher