Home › Engine / Hybrid System › N04C-VQ (ENGINE CONTROL) › ECD SYSTEM › 2017.01–2019.08
RM2850E _51 Engine / Hybrid System _073138 N04C-VQ ENGINE CONTROL _0355854 ECD SYSTEM C

N04C-VQ ENGINE CONTROL  ECD SYSTEM  P0088  Fuel Rail / System Pressure - Too High  P0627  Fuel Pump Control Circuit / Open  P1229  Fuel Pump System  


DESCRIPTION

The injection or supply pump assembly is a single-type pump and has a circuit for fuel suction that achieves high pressure force feed and reduction of driving torque, and for force feed process. The ECM controls the suction control valve, which operates fuel suction by the plunger in the process of suction.

When the internal fuel pressure of the common rail assembly exceeds the target pressure, the pressure limiter on the common rail assembly starts operating to control the internal fuel pressure of the common rail assembly.

DTC No. DTC Detection Condition Trouble Area
P0088 Conditions (a) and (b) are met 150 times or more (1 trip detection logic):

(a) Ignition switch ON

(b) Internal fuel pressure of the common rail: 250 MPa (2549 kgf/cm2, 36259 psi) or more


·

Injection or supply pump assembly

(suction control valve)

·

Open or short in suction control valve circuit

·

Common rail assembly

·

ECM


P0627 Open or short in suction control valve circuit for more than 0.5 seconds (1 trip detection logic)
·

Injection or supply pump assembly

(suction control valve)

·

Open or short in suction control valve circuit

·

Common rail assembly

·

ECM


P1229 Fuel over-feed (1 trip detection logic):
The actual fuel pressure exceeds the target fuel pressure by 40000 kPa or higher for 10 seconds
·

Injection or supply pump assembly

(suction control valve)

·

Open or short in suction control valve circuit

·

Common rail assembly

·

ECM



WIRING DIAGRAM

CAUTION / NOTICE / HINT

NOTICE:
·

After replacing the ECM, the new ECM needs registration (Click hereEngine / Hybrid System>N04C-VQ (ENGINE CONTROL)>ECD SYSTEM>REGISTRATION) and initialization (Click hereEngine / Hybrid System>N04C-VQ (ENGINE CONTROL)>ECD SYSTEM>INITIALIZATION).

·

After replacing the injection or supply pump assembly, the ECM needs initialization (Click hereEngine / Hybrid System>N04C-VQ (ENGINE CONTROL)>ECD SYSTEM>INITIALIZATION).



HINT:

Read freeze frame data using the GTS. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can be helpful in determining whether the vehicle was moving or stationary, whether the engine was warmed up or not, as well as other data recorded at the time of a malfunction.


PROCEDURE

1.CHECK OTHER DTC OUTPUT
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.


e.

Rear the DTCs.


Result:
Result Proceed to
DTC P0087, P0180, P0182, P0183, P0190, P0191, P0192, P0193, P0201, P0202, P0203, P0204 or P062D is not output A
DTC P0087, P0180, P0182, P0183, P0190, P0191, P0192, P0193, P0201, P0202, P0203, P0204 or P062D is output B



A

2.INSPECT INJECTION OR SUPPLY PUMP ASSEMBLY (SUCTION CONTROL VALVE)

B

2.INSPECT INJECTION OR SUPPLY PUMP ASSEMBLY (SUCTION CONTROL VALVE)
a.

Inspect the injection or supply pump assembly (suction control valve) (Click hereEngine / Hybrid System>N04C-VQ (FUEL)>FUEL SUPPLY PUMP>INSPECTION).


Result:
Proceed to
OK
NG



OK

3.CHECK DTC OUTPUT

NG

12.INSPECT FUEL INJECTION SYSTEM
3.CHECK DTC OUTPUT
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.


e.

Read the DTCs.


Result:
Result Proceed to
DTC P0088 and/or P1229 are output A
DTC P0627 is output B



A

4.INSPECT INJECTION OR SUPPLY PUMP ASSEMBLY (SUCTION CONTROL VALVE)

B

9.CHECK HARNESS AND CONNECTOR (SUCTION CONTROL VALVE - ECM)
4.INSPECT INJECTION OR SUPPLY PUMP ASSEMBLY (SUCTION CONTROL VALVE)
a.

Disconnect the suction control valve connector and then start the engine.

OK:

Engine does not start.



Result:
Proceed to
OK
NG



OK

5.READ VALUE USING GTS (TARGET PUMP SCV CURRENT)

NG

12.INSPECT FUEL INJECTION SYSTEM
5.READ VALUE USING GTS (TARGET PUMP SCV CURRENT)
a.

Connect the GTS to the DLC3.


b.

Start the engine.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine and ECT / Data List / Target Pump SCV Current.


e.

Read the value.

Standard:
Engine Speed Result
Idling 1350 to 2200 mA



Result:
Proceed to
OK
NG



OK

6.READ VALUE USING GTS (FUEL PRESSURE)

NG

12.INSPECT FUEL INJECTION SYSTEM
6.READ VALUE USING GTS (FUEL PRESSURE)
a.

Connect the GTS to the DLC3.


b.

Start the engine.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine and ECT / Data List / Fuel Press and Target Common Rail Pressure.


e.

Read the Value.

Standard:
GTS Display Condition Specified Condition
Fuel Press Idling 20000 to 30000 kPa
3000 rpm without Load 130000 to 150000 kPa
Target Common Rail Pressure Idling Deviation from Fuel Press within 5000 kPa
3000 rpm without Load Deviation from Fuel Press within 5000 kPa



Result:
Result Proceed to
NG A
OK B



A

7.CHECK HARNESS AND CONNECTOR (FUEL PRESSURE SENSOR - ECM)

B

9.CHECK HARNESS AND CONNECTOR (SUCTION CONTROL VALVE - ECM)
7.CHECK HARNESS AND CONNECTOR (FUEL PRESSURE SENSOR - ECM)
a.

Disconnect the ECM connector.


b.

Disconnect the fuel pressure sensor connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
B105-16 (PCR1) - m1-2 (PCR1) Always Below 1 Ω
B104-13 (VC) - m1-1 (VC1) Always Below 1 Ω
B104-14 (E2) - m1-3 (E1) Always Below 1 Ω
B105-2 (PCR2) - m1-5 (PCR2) Always Below 1 Ω
B105-13 (VC2) - m1-6 (VC2) Always Below 1 Ω
B105-14 (E21) - m1-4 (E2) Always Below 1 Ω
B105-16 (PCR1) or m1-2 (PCR1) - Body ground Always 10 kΩ or higher
B104-13 (VC) or m1-1 (VC1) - Body ground Always 10 kΩ or higher
B105-2 (PCR2) or m1-5 (PCR2) - Body ground Always 10 kΩ or higher
B105-13 (VC2) or m1-6 (VC2) - Body ground Always 10 kΩ or higher
B104-14 (E2) or m1-3 (E1) - Other terminals Always 10 kΩ or higher
B105-14 (E21) or m1-4 (E2) - Other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

8.READ VALUE USING GTS (FUEL PRESSURE)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (FUEL PRESSURE SENSOR - ECM)

8.READ VALUE USING GTS (FUEL PRESSURE)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine and ECT / Data List / Fuel Press.


e.

Wiggle the fuel pressure sensor connector and check that the fuel pressure reading does not change.

OK:

The fuel pressure reading does not change.



Result:
Proceed to
OK
NG



OK

12.INSPECT FUEL INJECTION SYSTEM

NG

REPLACE COMMON RAIL ASSEMBLY

9.CHECK HARNESS AND CONNECTOR (SUCTION CONTROL VALVE - ECM)
a.

Disconnect the suction control valve connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
B103-23 (PCV+) - B52-1 (SCV+) Always Below 1 Ω
B103-12 (PCV-) - B52-2 (SCV-) Always Below 1 Ω
B103-23 (PCV+) or B52-1 (SCV+) - Body ground Always 10 kΩ or higher
B103-12 (PCV-) or B52-2 (SCV-) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

10.CHECK ECM TERMINAL VOLTAGE (PCV+ AND PCV- TERMINAL)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (SUCTION CONTROL VALVE - ECM)

10.CHECK ECM TERMINAL VOLTAGE (PCV+ AND PCV- TERMINAL)
A256048E05
2.823,0.156 3.313,0.448 0.49,0.292 2.271,0.156 2.76,0.448 0.49,0.292 3.219,0.74 3.125,1.552 true 2.729,0.979 2.521,1.542 true 2.719,0.844 1.708,1.563 true 2.917,0.219 3.396,0.427 0.479,0.208 10 false B102 2.344,0.219 2.833,0.448 0.49,0.229 10 false B103 2.292,1.583 3.01,1.833 0.719,0.25 10 false 23 (PCV+) 1.469,1.583 2.198,1.813 0.729,0.229 10 false 12 (PCV-) 2.99,1.594 3.427,1.802 0.438,0.208 10 false 1 (E1) 2.792,3.646 3.396,3.896 0.604,0.25 10 false 10V/DIV. 2.792,3.938 3.313,4.198 0.521,0.26 10 false 1V/DIV. 0.156,3.594 0.604,3.792 0.448,0.198 10 false PCV+ 0.156,3.948 0.667,4.188 0.51,0.24 10 false PCV- 0.063,0.073 0.375,0.302 0.313,0.229 10 false *a 1.375,4.333 2.219,4.521 0.844,0.188 10 false 5 ms./DIV.

a.

While cranking or idling the engine, check the waveform of the ECM connector using an oscilloscope.

Standard:
Tester Connection Condition Tool Setting Specified Condition
B103-23 (PCV+) - B102-1 (E1) Idling or cranking with warm engine 10 V/DIV., 5 ms./ DIV. Correct waveform appears as shown
B103-12 (PCV-) - B102-1 (E1) Idling or cranking with warm engine 1 V/DIV., 5 ms./ DIV. Correct waveform appears as shown


Text in Illustration
*a Component with harness connected
(ECM)


Result:
Proceed to
OK
NG



OK

11.CHECK WHETHER DTC OUTPUT RECURS

NG

11.CHECK WHETHER DTC OUTPUT RECURS
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.



e.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.


f.

Read the DTCs.


Result:
Result Proceed to
DTC P0088, P0627 or P1229 is output A
DTC is not output B



A

12.INSPECT FUEL INJECTION SYSTEM

B

END

12.INSPECT FUEL INJECTION SYSTEM
a.

Inspect the fuel injection system circuit (Click hereEngine / Hybrid System>N04C-VQ (ENGINE CONTROL)>ECD SYSTEM>Fuel Injection System).


b.

Check whether the malfunction has been repairedsuccessfully.

OK:

Malfunction has been repaired successfully.



Result:
Proceed to
OK
NG



OK

END

NG