Home › Engine / Hybrid System › N04C-UH (FUEL) › COMMON RAIL › 2017.01–2021.01
RM2850E _51 Engine / Hybrid System _073175 N04C-UH FUEL _0356084 COMMON RAIL A

N04C-UH FUEL  COMMON RAIL  INSTALLATION  


PROCEDURE

Hide 1.INSTALL COMMON RAIL ASSEMBLY

a.

Install the common rail assembly with the 2 bolts.

Torque:

55 N*m (561 kgf*cm, 41 ft.*lbf)



b.

Connect the fuel hose.


c.

Connect the fuel pressure sensor connector.


Hide 2.INSTALL FUEL FILTER TO INJECTION PUMP FUEL PIPE

a.

Temporarily install the fuel filter to injection pump fuel pipe with the 2 union nuts.


b.

Using a union nut wrench (17 mm), tighten the union nuts.

Torque:

35 N*m (357 kgf*cm, 26 ft.*lbf)


NOTICE:
·

If the supply pump assembly has been replaced, the fuel filter to injection pump fuel pipe must also be replaced.

·

Refer to the torque above when not using the union nut wrench. When using the union nut wrench, calculate the torque in accordance with the lengths of the union nut wrench and torque wrench.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION




c.

Install the pipe clamp with the nut. Tighten the nut until the clamp's edges make contact with the engine side clamp's edges.


Hide 3.INSTALL INJECTION PIPE SUB-ASSEMBLY

a.

Temporarily install the 4 injection pipe sub-assemblies with the union nuts.


b.

Using a union nut wrench (17 mm), tighten the 8 union nuts.

Torque:

35 N*m (357 kgf*cm, 26 ft.*lbf)


NOTICE:
·

If the common rail has been replaced, the injection pipe sub-assemblies must also be replaced.

·

Refer to the torque above when not using the union nut wrench. When using the union nut wrench, calculate the torque in accordance with the lengths of the union nut wrench and torque wrench.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION




Hide 4.INSTALL INJECTION PIPE CLAMP

a.

Install the 2 injection pipe clamps with the 2 nuts. Tighten the nut until the clamp's edges make contact with the engine side clamp's edges.


Hide 5.INSTALL NO. 2 HARNESS BRACKET

a.

Install the No. 2 harness bracket with the 2 bolts.

Torque:

29 N*m (291 kgf*cm, 21 ft.*lbf)



b.

Engage the 3 harness clamps.


Hide 6.INSTALL NO. 2 INTAKE PIPE WITH EGR VALVE

Hide 16206 7.INSTALL WATER BY-PASS PIPE SUB-ASSEMBLY

Hide 17113 8.INSTALL INTAKE PIPE WITH VENTURI ASSEMBLY

Hide 15301 9.INSTALL OIL DIPSTICK GUIDE

Hide 44360 11.INSTALL VANE PUMP OIL RESERVOIR ASSEMBLY

Hide 25625B 12.INSTALL EGR VALVE BRACKET

Hide 13.INSTALL WIRE HARNESS AND CONNECTORS

Hide 25608 14.INSTALL EGR COOLER SUB-ASSEMBLY

Hide 17271 15.INSTALL NO. 1 TURBO INSULATOR

Hide 16206C 17.INSTALL WATER BY-PASS PIPE SUB-ASSEMBLY

Hide 58701A 19.INSTALL FRONT ENGINE SERVICE COVER PANEL SUB-ASSEMBLY (for LHD)

Hide 58701A 20.INSTALL FRONT ENGINE SERVICE COVER PANEL SUB-ASSEMBLY (for RHD)

Hide 33504F 21.INSTALL SHIFT LEVER SUB-ASSEMBLY (for Manual Transmission)

Hide 58841A 22.INSTALL SHIFTING HOLE COVER (for Automatic Transmission)

Hide 33503F 23.INSTALL TRANSMISSION FLOOR SHIFT ASSEMBLY (for Automatic Transmission)

Hide 33820B 24.CONNECT TRANSMISSION CONTROL CABLE ASSEMBLY (for RHD)

Hide 33820B 25.CONNECT TRANSMISSION CONTROL CABLE ASSEMBLY (for LHD)

Hide 58848A 26.INSTALL SHIFT LEVER HOLE COVER WITH BOOTS (for RHD)

Hide 27.BLEED AIR FROM FUEL SYSTEM

Hide 33531B 31.INSTALL SHIFT AND SELECT LEVER SHAFT DUST BOOT (for LHD)

Hide 58534A 32.INSTALL TRANSMISSION COVER MAT (for Manual Transmission)

Hide 58420 33.INSTALL NO. 2 ENGINE SERVICE HOLE COVER ASSEMBLY (for Automatic Transmission)

Hide 33820B 34.INSTALL TRANSMISSION CONTROL CABLE ASSEMBLY (for Automatic Transmission)

Hide 33820B 35.ADJUST TRANSMISSION CONTROL CABLE ASSEMBLY (for Automatic Transmission)

Hide 36. SHIFT LEVER POSITION (for Automatic Transmission)

Hide 58420 37.INSTALL NO. 2 ENGINE SERVICE HOLE COVER ASSEMBLY

Hide 58521D 38.INSTALL ENGINE SERVICE HOLE COVER MAT (w/o Carpet)

Hide 58734B 39.INSTALL ENGINE SERVICE COVER REAR WEATHERSTRIP

Hide 58410 40.INSTALL ENGINE SERVICE HOLE COVER

Hide 58521D 41.INSTALL ENGINE SERVICE HOLE COVER MAT (w/ Carpet)

Hide 51441D 42.INSTALL NO. 1 ENGINE UNDER COVER (for Plastic Type)

Hide 51441D 43.INSTALL NO. 1 ENGINE UNDER COVER (for Metal Type)

Hide 51459 44.INSTALL ENGINE SIDE COVER STAY (for TCAP Made)