Home › Engine / Hybrid System › 2TR-FE (ENGINE CONTROL) › SFI SYSTEM
RM2850E _51 Engine / Hybrid System _073287 2TR-FE ENGINE CONTROL _0357042 SFI SYSTEM C

2TR-FE ENGINE CONTROL  SFI SYSTEM  P0011  Camshaft Position "A" - Timing Over-Advanced or System Performance (Bank 1)  P0012  Camshaft Position "A" - Timing Over-Retarded (Bank 1)  


DESCRIPTION

Refer to DTC P0010 (Click here Engine / Hybrid System>2TR-FE (ENGINE CONTROL)>SFI SYSTEM>P0010).

DTC No. DTC Detection Condition Trouble Area
P0011 Advanced camshaft timing:
With warm engine and engine speed of between 500 rpm and 4,000 rpm, all conditions (a), (b) and (c) are met (1 trip detection logic):
(a) Difference between target and actual intake valve timings more than 5°CA (Crankshaft Angle) for 4.5 seconds
(b) Current intake valve timing fixed (timing changes less than 5°CA in 5 seconds)
(c) Variations in VVT controller timing more than 19°CA of maximum delayed timing (malfunction in advance timing)
·

Valve timing

·

Camshaft timing oil control valve assembly

·

Oil control valve filter

·

Camshaft timing gear assembly

·

ECM


P0012 Retarded camshaft timing:
With warm engine and engine speed of between 500 rpm and 4,000 rpm, all conditions (a), (b) and (c) are met (2 trip detection logic):
(a) Difference between target and actual intake valve timings more than 5°CA (Crankshaft Angle) for 4.5 seconds
(b) Current intake valve timing fixed (timing changes less than 5°CA in 5 seconds)
(c) Variations in VVT controller timing 19°CA or less of maximum delayed timing (malfunction in retarded timing)
·

Valve timing

·

Camshaft timing oil control valve assembly

·

Oil control valve filter

·

Camshaft timing gear assembly

·

ECM



MONITOR DESCRIPTION

The ECM optimizes the valve timing using the VVT system to control the intake valve camshaft. The VVT system includes the ECM, OCV and VVT actuator. The ECM sends a target "duty-cycle" control signal to the OCV. This control signal, applied to the OCV, regulates the oil pressure supplied to the VVT controller. The VVT controller can then advance or retard the intake valve camshaft.

Example:

A DTC will be set if: 1) the difference between the target and actual valve timing is more than 5° of the Crankshaft Angle (CA) and the condition continues for more than 4.5 seconds; or 2) the OCV is forcibly activated 63 times or more.

DTC P0011 (advanced cam timing) is subject to 1 trip detection logic.

DTC P0012 (retarded cam timing) is subject to 2 trip detection logic.

The monitor runs if all the conditions below are met:

-

After warming up the engine (engine coolant temperature 75°C (167°F) or more).

-

After driving the vehicle over 40 km/h (25 mph) for 3 minutes.

-

After idling the engine for 3 minutes.



WIRING DIAGRAM

CAUTION / NOTICE / HINT

NOTICE:

DTC P0011 or P0012 may be set when foreign objects in the engine oil are caught in some parts of the system. The DTC will remain set even if the system returns to normal after a short time. Foreign objects are filtered out by the oil filter.


HINT:

Read freeze frame data using the GTS. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air-fuel ratio was lean or rich, and other data from the time the malfunction occurred.


PROCEDURE

1.CHECK ANY OTHER DTCS OUTPUT (IN ADDITION TO DTC P0011 OR P0012)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS ON.


d.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.


e.

Read DTCs.

Result:
Result Proceed To
DTC P0011 or P0012 is output A
DTC P0011 or P0012 and other DTCs are output B


HINT:

If any other DTCs besides P0011 or P0012 are output, perform troubleshooting for those DTCs first.




A

2.PERFORM ACTIVE TEST USING GTS (OPERATE CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY)

B

2.PERFORM ACTIVE TEST USING GTS (OPERATE CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY)
a.

Connect the GTS to the DLC3.


b.

Start the engine.


c.

Turn the GTS ON.


d.

Warm up the engine.


e.

Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the VVT Linear (Bank 1).


f.

Check the engine speed while operating the Oil Control Valve (OCV) using the GTS.

Result
GTS Operation Specified Condition
0% Normal engine speed
100% Engine idles roughly or stalls


Result:
Proceed To
OK
NG



OK

3.CHECK WHETHER DTC OUTPUT RECURS (DTC P0011 OR P0012)

NG

4.INSPECT CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY
3.CHECK WHETHER DTC OUTPUT RECURS (DTC P0011 OR P0012)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS ON.



e.

Start the engine and warm it up.


f.

Switch the ECM from normal mode to check mode using the GTS.


g.

Drive the vehicle for more than 10 minutes.


h.

Read the output DTCs using the GTS.


Result:
Result Proceed To
DTC is not output A
DTC P0011 or P0012 is output B



A

B

7.CHECK VALVE TIMING (CHECK FOR LOOSENESS IN TIMING CHAIN AND WHETHER TIMING CHAIN HAS JUMPED TOOTH)
4.INSPECT CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY
a.

Inspect the camshaft timing oil control valve assembly (Click here Engine / Hybrid System>2TR-FE (ENGINE CONTROL)>CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY>INSPECTION).


Result:
Proceed To
OK
NG



OK

5.INSPECT OIL CONTROL VALVE FILTER

NG

5.INSPECT OIL CONTROL VALVE FILTER
a.
A099462

Remove the oil control valve filter.


b.

Check that the filter is not clogged.

OK:

Filter is not clogged.



Result:
Proceed To
OK
NG



OK

6.INSPECT CAMSHAFT TIMING GEAR ASSEMBLY

NG

CLEAN OIL CONTROL VALVE FILTER

6.INSPECT CAMSHAFT TIMING GEAR ASSEMBLY
a.

Inspect the camshaft timing gear assembly (Click here Engine / Hybrid System>2TR-FE (ENGINE MECHANICAL)>CAMSHAFT>INSPECTION).


Result:
Proceed To
OK
NG



OK

7.CHECK VALVE TIMING (CHECK FOR LOOSENESS IN TIMING CHAIN AND WHETHER TIMING CHAIN HAS JUMPED TOOTH)

NG

REPLACE CAMSHAFT TIMING GEAR ASSEMBLY

7.CHECK VALVE TIMING (CHECK FOR LOOSENESS IN TIMING CHAIN AND WHETHER TIMING CHAIN HAS JUMPED TOOTH)
a.
A430085E01
1.01,0.313 0.771,0.177 true 2.667,0.823 2.417,0.458 2.417,0.458 2.677,1.052 false 0.938,0.823 1,1.292 1,1.292 1.073,0.625 false 0.917,2.5 1.729,1.896 1.729,1.896 2.438,2.531 false 1.854,4.073 2.49,3.625 true 0.313,0.094 0.76,0.26 0.448,0.167 10 true 13°47' 2.24,0.292 2.458,0.5 0.219,0.208 10 false *a 0.458,1.292 1.292,1.469 0.833,0.177 10 true Timing Mark 1.625,1.708 1.844,1.917 0.219,0.208 10 false *a 2.521,3.5 2.74,3.708 0.219,0.208 10 false *b

Remove the cylinder head cover.


b.

Turn the crankshaft to align the timing marks of the crankshaft.


c.

Align the groove of the crankshaft pulley with the "0" position.


d.

Confirm whether the timing marks of the camshaft pulley and camshaft bearing cap are facing each other.


e.

If the timing marks are not facing each other, turn the crankshaft clockwise by 360°. Confirm again if the timing marks are facing each other.

OK:

The timing marks of the camshaft pulley and the cylinder head cover face each other when the groove of the crankshaft pulley is in the "0" position.


Text in Illustration
*a Timing Mark
*b Groove


Result:
Proceed To
OK
NG



OK

8.CHECK WHETHER DTC OUTPUT RECURS (DTC P0011 OR P0012)

NG

8.CHECK WHETHER DTC OUTPUT RECURS (DTC P0011 OR P0012)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS ON.



e.

Start the engine and warm it up.


f.

Switch the ECM from normal mode to check mode using the GTS.


g.

Drive the vehicle for more than 10 minutes.


h.

Read the output DTCs using the GTS.

OK:

No DTC output.


HINT:

DTC P0011 or P0012 is output when foreign objects in the engine oil are caught in some parts of the system. These codes will stay output for a short time even after the system returns to normal. These foreign objects are then captured by the oil filter, thus eliminating the source of the problem.



Result:
Proceed To
OK
NG



OK

END

NG