Home › Engine / Hybrid System › 2TR-FE (ENGINE CONTROL) › SFI SYSTEM
RM2850E _51 Engine / Hybrid System _073287 2TR-FE ENGINE CONTROL _0357042 SFI SYSTEM C

2TR-FE ENGINE CONTROL  SFI SYSTEM  P0016  Crankshaft Position - Camshaft Position Correlation (Bank 1 Sensor A)  


DESCRIPTION

In the VVT system, the appropriate intake valve open and close timing is controlled by the ECM. The ECM performs intake valve control by performing the following: 1) controlling the camshaft and camshaft oil control valve, and operating the camshaft timing gear; and 2) changing the relative positions of the gaps between the camshaft and crankshaft.

Refer to DTCs P0335 and P0339 (Click here Engine / Hybrid System>2TR-FE (ENGINE CONTROL)>SFI SYSTEM>P0335).

DTC No. DTC Detection Condition Suspected Area
P0016 Deviation in crankshaft position sensor signal and camshaft position signal
(2 trip detection logic)
·

Mechanical system (jumped tooth of timing chain or chain stretched)

·

Camshaft timing oil control valve assembly

·

Oil control valve filter

·

Camshaft timing gear assembly

·

ECM



MONITOR DESCRIPTION

To monitor the correlation of the intake camshaft position and crankshaft position, the ECM checks the VVT learning value while the engine is idling. The VVT learning value is calibrated based on the camshaft position and crankshaft position. The intake valve timing is set to the most retarded angle while the engine is idling. If the VVT learning value is out of the specified range in consecutive driving cycles, the ECM illuminates the MIL and sets the DTC P0016.

WIRING DIAGRAM

Refer to DTCs P0335 and P0339 (Click here Engine / Hybrid System>2TR-FE (ENGINE CONTROL)>SFI SYSTEM>P0335).

CAUTION / NOTICE / HINT

HINT:

Read freeze frame data using the GTS. Freeze frame data records the engine conditions when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air-fuel ratio was lean or rich, and other data from the time the malfunction occurred.


PROCEDURE

1.CHECK ANY OTHER DTCS OUTPUT (IN ADDITION TO DTC P0016)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS ON.


d.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.


e.

Read DTCs.

Result:
Result Proceed To
DTC P0016 is output A
DTC P0016 and other DTCs are output B


HINT:

If any other DTCs besides P0016 are output, perform troubleshooting for those DTCs first.




A

2.PERFORM ACTIVE TEST USING GTS (OPERATE CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY)

B

2.PERFORM ACTIVE TEST USING GTS (OPERATE CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY)
HINT:

If the VVT system can be operated through the Active Test, it can be assumed that the VVT system is operating normally.


a.

Connect the GTS to the DLC3.


b.

Start the engine.


c.

Turn the GTS ON.


d.

Warm up the engine.


e.

Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the VVT Linear (Bank 1) / Data List / VVT Change Angle #1.


f.

Perform the Active Test. Check that the displacement angle varies.

OK:

Displacement angle varies.



Result:
Proceed To
OK
NG



OK

3.CHECK WHETHER DTC OUTPUT RECURS (DTC P0016)

NG

4.INSPECT CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY
3.CHECK WHETHER DTC OUTPUT RECURS (DTC P0016)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS ON.



e.

Start the engine and warm it up.


f.

Switch the ECM from normal mode to check mode using the GTS.


g.

Drive the vehicle for more than 10 minutes.


h.

Read the output DTCs using the GTS.


Result:
Result Proceed To
DTC is not output A
DTC P0016 is output B



A

B

7.CHECK VALVE TIMING (CHECK FOR LOOSE TIMING CHAIN AND JUMPED TEETH)
4.INSPECT CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY
a.

Inspect the camshaft timing oil control valve assembly (Click here Engine / Hybrid System>2TR-FE (ENGINE CONTROL)>CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY>INSPECTION).


Result:
Proceed To
OK
NG



OK

5.INSPECT OIL CONTROL VALVE FILTER

NG

5.INSPECT OIL CONTROL VALVE FILTER
a.
A099462

Remove the oil control valve filter.


b.

Check that the filter is not clogged.

OK:

Filter is not clogged.



Result:
Proceed To
OK
NG



OK

6.INSPECT CAMSHAFT TIMING GEAR ASSEMBLY

NG

CLEAN OIL CONTROL VALVE FILTER

6.INSPECT CAMSHAFT TIMING GEAR ASSEMBLY
a.

Inspect the camshaft timing gear assembly (Click here Engine / Hybrid System>2TR-FE (ENGINE MECHANICAL)>CAMSHAFT>INSPECTION).


Result:
Proceed To
OK
NG



OK

7.CHECK VALVE TIMING (CHECK FOR LOOSE TIMING CHAIN AND JUMPED TEETH)

NG

REPLACE CAMSHAFT TIMING GEAR ASSEMBLY

7.CHECK VALVE TIMING (CHECK FOR LOOSE TIMING CHAIN AND JUMPED TEETH)
a.
A430085E01
1.01,0.313 0.771,0.177 true 2.667,0.823 2.417,0.458 2.417,0.458 2.677,1.052 false 0.938,0.823 1,1.292 1,1.292 1.073,0.625 false 0.917,2.5 1.729,1.896 1.729,1.896 2.438,2.531 false 1.854,4.073 2.49,3.625 true 0.313,0.094 0.76,0.26 0.448,0.167 10 true 13°47' 2.24,0.292 2.458,0.5 0.219,0.208 10 false *a 0.458,1.292 1.292,1.469 0.833,0.177 10 true Timing Mark 1.625,1.708 1.844,1.917 0.219,0.208 10 false *a 2.521,3.5 2.74,3.708 0.219,0.208 10 false *b

Remove the cylinder head cover.


b.

Turn the crankshaft to align the timing marks of the crankshaft.


c.

Align the groove of the crankshaft pulley with the "0" position.


d.

Confirm whether the timing marks of the camshaft pulley and camshaft bearing cap are facing each other.


e.

If the timing marks are not facing each other, turn the crankshaft clockwise by 360°. Confirm again if the timing marks are facing each other.

OK:

The timing marks of the camshaft pulley and the cylinder head cover face each other when the groove of the crankshaft pulley is in the "0" position.


Text in Illustration
*a Timing Mark
*b Groove


Result:
Proceed To
OK
NG



OK

8.CHECK WHETHER DTC OUTPUT RECURS (DTC P0016)

NG

8.CHECK WHETHER DTC OUTPUT RECURS (DTC P0016)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS ON.



e.

Start the engine and warm it up.


f.

Switch the ECM from normal mode to check mode using the GTS.


g.

Drive the vehicle for more than 10 minutes.


h.

Read the output DTCs using the GTS.

OK:

No DTC output.


HINT:

DTC P0011 or P0012 is output when foreign objects in the engine oil are caught in some parts of the system. These codes will stay output for a short time even after the system returns to normal. These foreign objects are then captured by the oil filter, thus eliminating the source of the problem.



Result:
Proceed To
OK
NG



OK

END

NG