Home › Engine / Hybrid System › N04C-WA (ENGINE CONTROL) › ECD SYSTEM › from 2019.08
RM2850E _51 Engine / Hybrid System _082611 N04C-WA ENGINE CONTROL _0399963 ECD SYSTEM C

N04C-WA ENGINE CONTROL  ECD SYSTEM  P229F  NOx Sensor Circuit Range/Performance Bank 1 Sensor 2  


DESCRIPTION

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P229F NOx Sensor Circuit Range/Performance Bank 1 Sensor 2 Diagnosis Condition:
·

DPR regenerating.

·

The condition that SCR catalyst temperature is high.

·

Exhaust fuel addition injector quantity is 5 mg/cyl/sec or more.

·

Total quantity of NOx flown back into SCR catalyst is in the range of 10 ppm to 1,500 ppm.

·

The exhaust gas flow rate is in the range of 40 kg/h to 1000 kg/h.

·

The No. 1 nitrogen oxides sensor is operating normally.


Malfunction Status:

The condition that the value, which is calculated using the following formula: (average NOx (SCR outlet)/ average NOx (SCR inlet), is less than 0.5 or greater than 1.4 remains for 10 seconds or more.


Malfunction Duration:

10 seconds or more


·

No. 2 nitrogen oxides sensor

·

Harness or connector


Class B1 DTC stored

MONITOR DESCRIPTION

·

No. 2 nitrogen oxides sensor is controlled by the nitrogen oxides sensor control.

·

The nitrogen oxides sensor control is connected via the DCU (emission control ECU) and a harness, and it sends and receives data.


CONFIRMATION DRIVING PATTERN

DTC No. DTC Detection Drive Pattern
P229F PM forced regeneration

WIRING DIAGRAM

CAUTION / NOTICE / HINT

NOTICE:

After replacing the ECM, the new ECM needs registration (Click hereEngine / Hybrid System>N04C-WA (ENGINE CONTROL)>ECD SYSTEM>REGISTRATION) and initialization (Click hereEngine / Hybrid System>N04C-WA (ENGINE CONTROL)>ECD SYSTEM>INITIALIZATION).


HINT:

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.


PROCEDURE

1.CHECK UREA SOLUTION (AdBlue)
a.

Measure the urea solution concentration.

Standard values:

30 to 35%



Result:
Proceed to
OK
NG



OK

2.CHECK EXHAUST PIPE

NG

33.REPLACE UREA SOLUTION (AdBlue)
2.CHECK EXHAUST PIPE
a.

Check for exhaust pipe crack, exhaust gas leak (soot contamination) and improper coupling flange tightening.


Result:
Proceed to
OK
NG



OK

3.CHECK CONNECTOR CONNECTION CONDITION (MASS AIR FLOW METER)

NG

32.REPAIR OR REPLACE EXHAUST PIPE
3.CHECK CONNECTOR CONNECTION CONDITION (MASS AIR FLOW METER)
a.

Check the connector connection for the mass air flow meter connector.

Standard:

The connector is connected securely and there are no contact pressure problems.



Result:
Proceed to
OK
NG



OK

4.CHECK MASS AIR FLOW METER

NG

31.CONNECT SECURELY
4.CHECK MASS AIR FLOW METER
a.

Check the installation of the mass air flow meter.


b.

Make sure there is no dirt, damage or clogging in the sensing unit of the sensor.


Result:
Proceed to
OK
NG



OK

5.CHECK CONNECTOR CONNECTION CONDITION (NO. 5 EXHAUST GAS TEMPERATURE SENSOR CONNECTOR)

NG

30.REPAIR OR REPLACE MASS AIR FLOW METER
5.CHECK CONNECTOR CONNECTION CONDITION (NO. 5 EXHAUST GAS TEMPERATURE SENSOR CONNECTOR)
a.

Check the connector connection for the No. 5 exhaust gas temperature sensor connector.

Standard:

The connector is connected securely and there are no contact pressure problems.



Result:
Proceed to
OK
NG



OK

6.CHECK NO. 5 EXHAUST GAS TEMPERATURE SENSOR

NG

29.CONNECT SECURELY
6.CHECK NO. 5 EXHAUST GAS TEMPERATURE SENSOR
a.

Check the installation of the No. 5 exhaust gas temperature sensor.


b.

Make sure there is no dirt, damage or clogging in the sensing unit of No. 5 exhaust gas temperature sensor.


Result:
Proceed to
OK
NG



OK

7.INSPECT NO. 5 EXHAUST GAS TEMPERATURE SENSOR

NG

28.REPAIR OR REPLACE NO. 5 EXHAUST GAS TEMPERATURE SENSOR
7.INSPECT NO. 5 EXHAUST GAS TEMPERATURE SENSOR
a.

Inspect the No. 5 exhaust gas temperature sensor.

Click hereEngine / Hybrid System>N04C-WA (EMISSION CONTROL)>EXHAUST GAS TEMPERATURE SENSOR>REMOVAL


Result:
Proceed to
OK
NG



OK

8.CHECK CONNECTOR CONNECTION CONDITION (NO. 4 EXHAUST GAS TEMPERATURE SENSOR CONNECTOR)

NG

27.REPLACE NO. 5 EXHAUST GAS TEMPERATURE SENSOR
8.CHECK CONNECTOR CONNECTION CONDITION (NO. 4 EXHAUST GAS TEMPERATURE SENSOR CONNECTOR)
a.

Check the connector connection for the No. 4 exhaust gas temperature sensor connector.

Standard:

The connector is connected securely and there are no contact pressure problems.



Result:
Proceed to
OK
NG



OK

9.CHECK NO. 4 EXHAUST GAS TEMPERATURE SENSOR

NG

26.CONNECT SECURELY
9.CHECK NO. 4 EXHAUST GAS TEMPERATURE SENSOR
a.

Check the installation of the No. 4 exhaust gas temperature sensor.


b.

Make sure there is no dirt, damage or clogging in the sensing unit of No. 4 exhaust gas temperature sensor.


Result:
Proceed to
OK
NG



OK

10.INSPECT NO. 4 EXHAUST GAS TEMPERATURE SENSOR

NG

25.REPAIR OR REPLACE NO. 4 EXHAUST GAS TEMPERATURE SENSOR
10.INSPECT NO. 4 EXHAUST GAS TEMPERATURE SENSOR
a.

Inspect the No. 4 exhaust gas temperature sensor.

Click hereEngine / Hybrid System>N04C-WA (EMISSION CONTROL)>EXHAUST GAS TEMPERATURE SENSOR>INSPECTION


Result:
Proceed to
OK
NG



OK

11.CHECK CONNECTOR CONNECTION CONDITION (AMBIENT TEMPERATURE SENSOR (COOLER THERMISTOR))

NG

24.REPLACE NO. 4 EXHAUST GAS TEMPERATURE SENSOR
11.CHECK CONNECTOR CONNECTION CONDITION (AMBIENT TEMPERATURE SENSOR (COOLER THERMISTOR))
a.

Check the connector connection for the ambient temperature sensor (cooler thermistor) connector.

Standard:

The connector is connected securely and there are no contact pressure problems.



Result:
Proceed to
OK
NG



OK

12.CHECK AMBIENT TEMPERATURE SENSOR (COOLER THERMISTOR)

NG

23.CONNECT SECURELY
12.CHECK AMBIENT TEMPERATURE SENSOR (COOLER THERMISTOR)
a.

Check the installation of the ambient temperature sensor (cooler thermistor).


b.

Make sure there is no dirt, damage or clogging in the sensing unit of ambient temperature sensor (cooler thermistor).


Result:
Proceed to
OK
NG



OK

13.INSPECT AMBIENT TEMPERATURE SENSOR (COOLER THERMISTOR)

NG

22.REPAIR OR REPLACE AMBIENT TEMPERATURE SENSOR (COOLER THERMISTOR)
13.INSPECT AMBIENT TEMPERATURE SENSOR (COOLER THERMISTOR)
a.

Result:
Proceed to
OK
NG



OK

14.CHECK UREA INJECTOR SET

NG

21.REPLACE AMBIENT TEMPERATURE SENSOR (COOLER THERMISTOR)
14.CHECK UREA INJECTOR SET
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Urea Selective Catalytic Reduction / Data List / Reductant Level.


e.

Check the value of "Reductant Level". If the value of the level is 11 L or less, refill the urea solution.


f.

Remove the urea injector assembly from the front exhaust pipe assembly.

Click hereEngine / Hybrid System>N04C-WA (EMISSION CONTROL)>UREA INJECTOR>REMOVAL

HINT:
·

Do not disconnect the urea injector assembly from the urea tube with heater assembly.

·

Use a cover, etc., to prevent foreign matter from entering the exhaust pipe.




g.

Prepare a bucket or other receptacle for collecting urea solution from the urea injector assembly.


h.

Enter the following menus: Powertrain / Urea Selective Catalytic Reduction / Utility / Reductant Injection / Pattern 1 to 3.


i.

Perform "Pattern 1" to "Pattern 3" and check the urea solution injection volume.


Standard Value:
Reductant Injection Urea Solution Injection Volume
Pattern 3 45 to 55 cc
Pattern 2 16 to 24 cc
Pattern 1 7 to 13 cc


Result:
Proceed to
OK
NG



OK

15.REPLACE NO. 1 NITROGEN OXIDES SENSOR AND NO. 2 NITROGEN OXIDES SENSOR

NG

20.REPLACE UREA INJECTOR SET
15.REPLACE NO. 1 NITROGEN OXIDES SENSOR AND NO. 2 NITROGEN OXIDES SENSOR
a.

Replace the No. 1 nitrogen oxides sensor and No. 2 nitrogen oxides sensor.

Click hereEngine / Hybrid System>N04C-WA (ENGINE CONTROL)>NITROGEN OXIDES SENSOR>REMOVAL


Result:
Proceed to
NEXT



NEXT

16.PERFORM PM FORCED REGENERATION
16.PERFORM PM FORCED REGENERATION
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Enter the following menus: Powertrain / Engine / Utility / DPR Check.

i.

Select "Check Start" and check according to the GTS display.


ii.

Select "DPR ALL Items Reset" and reset according to the GTS display.


iii.

Exit the inspection screen.



d.

Clear the DTCs.

HINT:

Clear the DTCs with the engine stopped, as DTCs cannot be cleared while the engine is running.




Result:
Proceed to
NEXT



NEXT

17.CHECK DTC OUTPUT
17.CHECK DTC OUTPUT
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Enter the following menus: Powertrain / Engine / Trouble Codes.


d.

Read Current DTCs.


Result:
Result Proceed to
DTC P229F is output A
DTCs are not output B



A

18.REPLACE ECM

B

END

18.REPLACE ECM

Result:
Proceed to
NEXT



NEXT

19.CHECK DTC OUTPUT
19.CHECK DTC OUTPUT
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Clear the DTCs.

HINT:

Clear the DTCs with the engine stopped, as DTCs cannot be cleared while the engine is running.



d.

Turn the ignition switch off for 30 seconds or more.


e.

Perform the confirmation driving pattern.


f.

Turn the GTS on.


g.

Enter the following menus: Powertrain / Engine / Trouble Codes.


h.

Confirm that the DTC is not output again.


Result:
Proceed to
NEXT



NEXT

END

20.REPLACE UREA INJECTOR SET

Result:
Proceed to
NEXT



NEXT

16.PERFORM PM FORCED REGENERATION
21.REPLACE AMBIENT TEMPERATURE SENSOR (COOLER THERMISTOR)
a.

Replace the ambient temperature sensor (cooler thermistor).

Click hereEngine / Hybrid System>N04C-WA (EMISSION CONTROL)>AMBIENT TEMPERATURE SENSOR (for Urea SCR System)>REMOVAL


Result:
Proceed to
NEXT



NEXT

16.PERFORM PM FORCED REGENERATION
22.REPAIR OR REPLACE AMBIENT TEMPERATURE SENSOR (COOLER THERMISTOR)
a.

Repair or replace the ambient temperature sensor (cooler thermistor).

HINT:

Clean the sensing unit and install it properly.

If damaged, replace the ambient temperature sensor (cooler thermistor).



Result:
Proceed to
NEXT



NEXT

16.PERFORM PM FORCED REGENERATION
23.CONNECT SECURELY
a.

Connect securely the ambient temperature sensor (cooler thermistor) connector.

HINT:

Repair it as needed.



Result:
Proceed to
NEXT



NEXT

16.PERFORM PM FORCED REGENERATION
24.REPLACE NO. 4 EXHAUST GAS TEMPERATURE SENSOR
a.

Replace the No. 4 exhaust gas temperature sensor.

Click hereEngine / Hybrid System>N04C-WA (EMISSION CONTROL)>EXHAUST GAS TEMPERATURE SENSOR>REMOVAL


Result:
Proceed to
NEXT



NEXT

16.PERFORM PM FORCED REGENERATION
25.REPAIR OR REPLACE NO. 4 EXHAUST GAS TEMPERATURE SENSOR
a.

Repair or replace the No. 4 exhaust gas temperature sensor.

HINT:

Clean the sensing unit and install it properly.

If damaged, replace the No. 4 exhaust gas temperature sensor.



Result:
Proceed to
NEXT



NEXT

16.PERFORM PM FORCED REGENERATION
26.CONNECT SECURELY
a.

Connect securely the No. 4 exhaust gas temperature sensor connector.

HINT:

Repair it as needed.



Result:
Proceed to
NEXT



NEXT

16.PERFORM PM FORCED REGENERATION
27.REPLACE NO. 5 EXHAUST GAS TEMPERATURE SENSOR
a.

Replace the No. 5 exhaust gas temperature sensor.

Click hereEngine / Hybrid System>N04C-WA (EMISSION CONTROL)>EXHAUST GAS TEMPERATURE SENSOR>REMOVAL


Result:
Proceed to
NEXT



NEXT

16.PERFORM PM FORCED REGENERATION
28.REPAIR OR REPLACE NO. 5 EXHAUST GAS TEMPERATURE SENSOR
a.

Repair or replace the No. 5 exhaust gas temperature sensor.

HINT:

Clean the sensing unit and install it properly.

If damaged, replace the No. 5 exhaust gas temperature sensor.



Result:
Proceed to
NEXT



NEXT

16.PERFORM PM FORCED REGENERATION
29.CONNECT SECURELY
a.

Connect securely the No. 5 exhaust gas temperature sensor connector.

HINT:

Repair it as needed.



Result:
Proceed to
NEXT



NEXT

16.PERFORM PM FORCED REGENERATION
30.REPAIR OR REPLACE MASS AIR FLOW METER
a.

Mass air flow meter carry out air blow from the suction port of the main body and install it properly.

HINT:

If damaged, replace the mass air flow meter.



Result:
Proceed to
NEXT



NEXT

16.PERFORM PM FORCED REGENERATION
31.CONNECT SECURELY
a.

Connect securely the mass air flow meter connector.

HINT:

Repair it as needed.



Result:
Proceed to
NEXT



NEXT

16.PERFORM PM FORCED REGENERATION
32.REPAIR OR REPLACE EXHAUST PIPE
a.

Repair the exhaust pipe.

HINT:

Replace it as needed.



Result:
Proceed to
NEXT



NEXT

16.PERFORM PM FORCED REGENERATION
33.REPLACE UREA SOLUTION (AdBlue)
a.

Replace the urea solution (AdBlue)


HINT:

If the urea solution concentration is below the standard, drain the urea solution through the tank drain with the key ON, and then refill the tank with at least 5 liters of urea solution.

Afterward, drive the vehicle and check if the problem does not recur under driving conditions.


Result:
Proceed to
NEXT



NEXT

16.PERFORM PM FORCED REGENERATION