The pressure sensor embedded in the urea pump is used to check the pressure in the urea pump.
Disconnections and short circuits in the pressure sensor of the urea pump are detected by the DCU (emission control ECU assembly).
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | MIL | Warning Indicate | Memory |
|---|---|---|---|---|---|---|
| P204C11 | Reductant Pressure Sensor Circuit Low Circuit Short to Ground | Diagnosis Condition:
·
Ignition switch ON. Malfunction Status: ·
The pressure sensor voltage is below 0.419 V. Malfunction Duration: ·
3 seconds or more. |
·
Open or short in pressure sensor (urea pump) circuit ·
Pressure sensor (urea pump) ·
DCU (emission control ECU assembly) |
Class A | AdBlue consumption warning light:
Comes on |
DTC stored |
Low voltage abnormality is detected in the pressure sensor located in the urea pump.
Procedure to turn off MIL and AdBlue consumption warning light by returning system to normal.
With the urea solution not frozen, start the engine.
When the exhaust gas temperature is 160°C (320°F) or more, the urea SCR system starts and diagnosis of the urea pump and urea injector assembly is performed. After diagnosis is complete, stop the engine.
Repeat the above procedure 3 times.
When the urea SCR system determines that it is normal after starting 1 time, the illuminated MIL remains illuminated and the AdBlue consumption warning light turns off. When the urea SCR system determines that it is normal after starting 3 times, the MIL turns off.
Procedure to turn off MIL and AdBlue consumption warning light after repairs.
After repairs are complete, connect the GTS and clear* the urea SCR system DTCs.
When the engine starts, check that the MIL illuminates and the AdBlue consumption warning light turns off. After 1 minute elapses, stop the engine. Start the engine again and check that the MIL turns off and the system returns to normal.
(*: The ECM malfunction information is not cleared, even if the urea SCR system DTCs are cleared. However, the command that caused the MIL to continuously illuminate is cleared.)
| DTC No. | DTC Detection Drive Pattern |
|---|---|
| P204C11 | Ignition switch ON for 5 seconds or more. |
For the circuit diagram of the pressure sensor (urea pump) refer to the DTC P0642A2.
Click hereEngine / Hybrid System>N04C-WA (EMISSION CONTROL)>UREA SELECTIVE CATALYTIC REDUCTION SYSTEM>P0642A2
For the circuit diagram of the SGN4 terminal refer to the DTC P007162.
Click hereEngine / Hybrid System>N04C-WA (EMISSION CONTROL)>UREA SELECTIVE CATALYTIC REDUCTION SYSTEM>P007162
For the circuit diagram of the ELU terminal refer to the DTC P0652A2.
Click hereEngine / Hybrid System>N04C-WA (EMISSION CONTROL)>UREA SELECTIVE CATALYTIC REDUCTION SYSTEM>P0652A2
For the circuit diagram of the ISG terminal refer to the DTC P202E71.
Click hereEngine / Hybrid System>N04C-WA (EMISSION CONTROL)>UREA SELECTIVE CATALYTIC REDUCTION SYSTEM>P202E71
For the circuit diagram of the ETHU terminal refer to the DTC P205B62.
Click hereEngine / Hybrid System>N04C-WA (EMISSION CONTROL)>UREA SELECTIVE CATALYTIC REDUCTION SYSTEM>P205B62
For the circuit diagram of the MSG terminal refer to the DTC P208C11.
Click hereEngine / Hybrid System>N04C-WA (EMISSION CONTROL)>UREA SELECTIVE CATALYTIC REDUCTION SYSTEM>P208C11
Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.
Check the connector connection and contact pressure of the pressure sensor (urea pump) connector.
The connector is connected securely and there are no contact pressure problems.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Check the connector connection and contact pressure of the DCU (emission control ECU assembly) connector.
The connector is connected securely and there are no contact pressure problems.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *a | Signal Check Harness No. 2 Lead Connector |
| *a | Signal Check Harness No. 2 Lead Connector |
| *a | Front view of wire harness connector
(to Pressure Sensor (Urea Pump)) |
Disconnect the pressure sensor (urea pump) connector.
Disconnect the DCU (emission control ECU assembly) connector.
Connect the signal check harness No. 2 to the DCU (emission control ECU assembly) vehicle side harness. (Do not connect the harness to the DCU (emission control ECU assembly).)
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| E-25 (VCPU) - P11-5 (VCPU) | Ignition switch off | Below 1 Ω |
| E-44 (EPU) - P11-3 (EPU) | Ignition switch off | Below 1 Ω |
| E-56 (PU) - P11-4 (PU) | Ignition switch off | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *a | Signal Check Harness No. 2 Lead Connector |
| *a | Signal Check Harness No. 2 Lead Connector |
Connect the signal check harness No. 2 to the DCU (emission control ECU assembly) vehicle side harness. (Do not connect the harness to the DCU (emission control ECU assembly).)
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| E-25 (VCPU) - Body ground | Ignition switch off | 10 kΩ or higher |
| E-44 (EPU) - Body ground | Ignition switch off | 10 kΩ or higher |
| E-56 (PU) - Body ground | Ignition switch off | 10 kΩ or higher |
| E-56 (PU) - E-36 (ELU) | Ignition switch off | 10 kΩ or higher |
| E-56 (PU) - E-37 (ISG) | Ignition switch off | 10 kΩ or higher |
| E-56 (PU) - E-43 (ETHU) | Ignition switch off | 10 kΩ or higher |
| E-56 (PU) - E-44 (EPU) | Ignition switch off | 10 kΩ or higher |
| E-56 (PU) - E-45 (MSG) | Ignition switch off | 10 kΩ or higher |
| E-56 (PU) - E-60 (SGN4) | Ignition switch off | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *a | Component without harness connected
(Pressure Sensor (Urea Pump)) |
Disconnect the pressure sensor (urea pump) connector.
Check that the pressure sensor (urea pump) terminal is free of bending and damage.
Pressure sensor (urea pump) terminal is free of bending and damage.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *a | Component without harness connected
(DCU (Emission Control ECU Assembly)) |
Disconnect the DCU (emission control ECU assembly) connector.
Check that the DCU (emission control ECU assembly) terminal is free of bending and damage.
DCU (emission control ECU assembly) terminal is free of bending and damage.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Clear the DTCs.
Clear the DTCs with the engine stopped, as DTCs cannot be cleared while the engine is running.
Turn the ignition switch off and wait for at least 30 seconds.
| Proceed to |
|---|
| NEXT |
NEXT
Drive the vehicle in accordance with the driving pattern described in the Confirmation Driving Pattern.
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Enter the following menus: Powertrain / Urea Selective Catalytic Reduction / Trouble Codes.
Read the DTCs.
| Result | Proceed to |
|---|---|
| DTC P204C11 is output | A |
| DTCs are not output | B |
A
B
Replace the pressure sensor (urea pump).
Click hereEngine / Hybrid System>N04C-WA (EMISSION CONTROL)>UREA PUMP>REMOVAL
| Proceed to |
|---|
| NEXT |
NEXT
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Clear the DTCs.
Clear the DTCs with the engine stopped, as DTCs cannot be cleared while the engine is running.
Turn the ignition switch off and wait for at least 30 seconds.
| Proceed to |
|---|
| NEXT |
NEXT
Drive the vehicle in accordance with the driving pattern described in the Confirmation Driving Pattern.
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Enter the following menus: Powertrain / Urea Selective Catalytic Reduction / Trouble Codes.
Read the DTCs.
| Result | Proceed to |
|---|---|
| DTC P204C11 is output | A |
| DTCs are not output | B |
A
B
Replace the DCU (emission control ECU assembly).
Click hereEngine / Hybrid System>N04C-WA (EMISSION CONTROL)>UREA PUMP CONTROL ECU>REMOVAL
| Proceed to |
|---|
| NEXT |
NEXT
Replace the pressure sensor (urea pump).
Click hereEngine / Hybrid System>N04C-WA (EMISSION CONTROL)>UREA PUMP CONTROL ECU>REMOVAL
| Proceed to |
|---|
| NEXT |
NEXT
Repair or replace the harness or connector.
| Proceed to |
|---|
| NEXT |
NEXT
Repair or replace the harness or connector.
| Proceed to |
|---|
| NEXT |
NEXT
Securely connect the DCU (emission control ECU assembly) connector.
Repair parts as necessary.
| Proceed to |
|---|
| NEXT |
NEXT
Securely connect the pressure sensor (urea pump) connector.
Repair parts as necessary.
| Proceed to |
|---|
| NEXT |
NEXT
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Clear the DTCs.
Clear the DTCs with the engine stopped, as DTCs cannot be cleared while the engine is running.
Turn the ignition switch off and wait for at least 30 seconds.
| Proceed to |
|---|
| NEXT |
NEXT
Drive the vehicle in accordance with the driving pattern described in the Confirmation Driving Pattern.
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Enter the following menus: Powertrain / Urea Selective Catalytic Reduction / Trouble Codes.
Read the DTCs.
DTCs are not output
| Proceed to |
|---|
| NEXT |
NEXT