Home › Engine / Hybrid System › N04C-WA (EMISSION CONTROL) › UREA SELECTIVE CATALYTIC REDUCTION SYSTEM › from 2019.08
RM2850E _51 Engine / Hybrid System _082614 N04C-WA EMISSION CONTROL _0400651 UREA SELECTIVE CATALYTIC REDUCTION SYSTEM C

N04C-WA EMISSION CONTROL  UREA SELECTIVE CATALYTIC REDUCTION SYSTEM  P248111  Exhaust Gas Temperature Sensor Circuit Low Bank 1 Sensor 5 Circuit Short to Ground  


DESCRIPTION

The No. 5 exhaust gas temperature sensor monitors the temperature at the SCR upstream.

The No. 5 exhaust gas temperature sensor detects disconnection and short-circuit based on the circuit voltage and signals in the DCU (emission control ECU assembly).

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Warning Indicate Memory
P248111 Exhaust Gas Temperature Sensor Circuit Low Bank 1 Sensor 5 Circuit Short to Ground Diagnosis Condition:
·

Ignition switch ON.


Malfunction Status:
·

The No. 5 exhaust gas temperature sensor voltage is below 0.02 V.


Malfunction Duration:
·

3 seconds or more.


·

Open or short in No. 5 exhaust gas temperature sensor circuit

·

No. 5 exhaust gas temperature sensor

·

DCU (emission control ECU assembly)


Class A AdBlue consumption warning light:
Comes on
DTC stored

MONITOR DESCRIPTION

Description of malfunction

Failure of No. 5 exhaust gas temperature sensor is detected.


Reset condition

After having restored to the normal conditions.


CONFIRMATION DRIVING PATTERN

DTC No. DTC Detection Drive Pattern
P248111 Idle the engine for 3 seconds after warming up the engine (the engine coolant temperature is 80°C (176°F) or higher).

WIRING DIAGRAM

·

For the circuit diagram of the No. 5 exhaust gas temperature sensor refer to the DTC P007162.

Click hereEngine / Hybrid System>N04C-WA (EMISSION CONTROL)>UREA SELECTIVE CATALYTIC REDUCTION SYSTEM>P007162

·

For the circuit diagram of the EPU terminal refer to the DTC P0642A2.

Click hereEngine / Hybrid System>N04C-WA (EMISSION CONTROL)>UREA SELECTIVE CATALYTIC REDUCTION SYSTEM>P0642A2

·

For the circuit diagram of the ELU terminal refer to the DTC P0652A2.

Click hereEngine / Hybrid System>N04C-WA (EMISSION CONTROL)>UREA SELECTIVE CATALYTIC REDUCTION SYSTEM>P0652A2

·

For the circuit diagram of the ISG terminal refer to the DTC P202E71.

Click hereEngine / Hybrid System>N04C-WA (EMISSION CONTROL)>UREA SELECTIVE CATALYTIC REDUCTION SYSTEM>P202E71

·

For the circuit diagram of the ETHU terminal refer to the DTC P205B62.

Click hereEngine / Hybrid System>N04C-WA (EMISSION CONTROL)>UREA SELECTIVE CATALYTIC REDUCTION SYSTEM>P205B62

·

For the circuit diagram of the MSG terminal refer to the DTC P208C11.

Click hereEngine / Hybrid System>N04C-WA (EMISSION CONTROL)>UREA SELECTIVE CATALYTIC REDUCTION SYSTEM>P208C11


CAUTION / NOTICE / HINT

HINT:

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.


PROCEDURE

1.CHECK CONNECTOR CONNECTION CONDITION (NO. 5 EXHAUST GAS TEMPERATURE SENSOR)
a.

Check the connector connection and contact pressure of the No. 5 exhaust gas temperature sensor connector.

OK:

The connector is connected securely and there are no contact pressure problems.



Result:
Proceed to
OK
NG



OK

2.INSPECT NO. 5 EXHAUST GAS TEMPERATURE SENSOR

NG

13.CONNECT SECURELY
2.INSPECT NO. 5 EXHAUST GAS TEMPERATURE SENSOR
a.

Check the installation condition (rattling and looseness) of the No. 5 exhaust gas temperature sensor.


b.

Check that the sensing part of the No. 5 exhaust gas temperature sensor is free of dirt, blockage and damage.


OK:

The sensing part of the No. 5 exhaust gas temperature sensor is normal and the No. 5 exhaust gas temperature sensor is correctly installed.


Result:
Proceed to
OK
NG



OK

3.INSPECT NO. 5 EXHAUST GAS TEMPERATURE SENSOR

NG

12.REPAIR OR REPLACE NO. 5 EXHAUST GAS TEMPERATURE SENSOR
3.INSPECT NO. 5 EXHAUST GAS TEMPERATURE SENSOR
a.

Inspect the No. 5 exhaust gas temperature sensor.

Click hereEngine / Hybrid System>N04C-WA (EMISSION CONTROL)>EXHAUST GAS TEMPERATURE SENSOR>INSPECTION


Result:
Proceed to
OK
NG



OK

4.CHECK HARNESS AND CONNECTOR (NO. 5 EXHAUST GAS TEMPERATURE SENSOR - DCU (EMISSION CONTROL ECU ASSEMBLY))

NG

11.REPLACE NO. 5 EXHAUST GAS TEMPERATURE SENSOR
4.CHECK HARNESS AND CONNECTOR (NO. 5 EXHAUST GAS TEMPERATURE SENSOR - DCU (EMISSION CONTROL ECU ASSEMBLY))
a.
A405886C01
1.51,0.125 1.885,0.406 0.375,0.281 0.083,0.115 0.396,0.313 0.313,0.198 10 false *a 1.667,0.208 1.979,0.406 0.313,0.198 10 false E
*a Signal Check Harness No. 2 Lead Connector


A405887C01
1.521,0.125 1.885,0.396 0.365,0.271 0.073,0.104 0.385,0.302 0.313,0.198 10 false *a 1.677,0.198 1.833,0.396 0.156,0.198 10 false E
*a Signal Check Harness No. 2 Lead Connector


Connect the signal check harness No. 2 to the DCU (emission control ECU assembly) vehicle side harness. (Do not connect the harness to the DCU (emission control ECU assembly).)


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
E-57 (EGT1) - Body ground Ignition switch off 10 kΩ or higher
E-60 (SGN4) - Body ground Ignition switch off 10 kΩ or higher
E-57 (EGT1) - E-36 (ELU) Ignition switch off 10 kΩ or higher
E-57 (EGT1) - E-37 (ISG) Ignition switch off 10 kΩ or higher
E-57 (EGT1) - E-43 (ETHU) Ignition switch off 10 kΩ or higher
E-57 (EGT1) - E-44 (EPU) Ignition switch off 10 kΩ or higher
E-57 (EGT1) - E-45 (MSG) Ignition switch off 10 kΩ or higher
E-57 (EGT1) - E-60 (SGN4) Ignition switch off 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

5.CHECK HARNESS AND CONNECTOR (NO. 5 EXHAUST GAS TEMPERATURE SENSOR - DCU (EMISSION CONTROL ECU ASSEMBLY))

NG

10.REPAIR OR REPLACE HARNESS OR CONNECTOR
5.CHECK HARNESS AND CONNECTOR (NO. 5 EXHAUST GAS TEMPERATURE SENSOR - DCU (EMISSION CONTROL ECU ASSEMBLY))
a.
A405887C01
1.521,0.125 1.885,0.396 0.365,0.271 0.073,0.104 0.385,0.302 0.313,0.198 10 false *a 1.677,0.198 1.833,0.396 0.156,0.198 10 false E
*a Signal Check Harness No. 2 Lead Connector


Connect the No. 5 exhaust gas temperature sensor connector.


b.

Connect the signal check harness No. 2 to the DCU (emission control ECU assembly) vehicle side harness. (Do not connect the harness to the DCU (emission control ECU assembly).)


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
E-57 (EGT1) - E-60 (SGN4) 20°C 13.7 to 29.8 kΩ
50°C 7.13 to 13.7 kΩ
80°C 4.1 to 7.13 kΩ



Result:
Proceed to
OK
NG



OK

6.CLEAR DTC

NG

9.REPAIR OR REPLACE HARNESS OR CONNECTOR
6.CLEAR DTC
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Clear the DTCs.

NOTICE:

Clear the DTCs with the engine stopped, as DTCs cannot be cleared while the engine is running.



e.

Turn the ignition switch off and wait for at least 30 seconds.


Result:
Proceed to
NEXT



NEXT

7.CHECK WHETHER DTC OUTPUT RECURS (DTC P248111)
7.CHECK WHETHER DTC OUTPUT RECURS (DTC P248111)
a.

Drive the vehicle in accordance with the driving pattern described in the Confirmation Driving Pattern.


b.

Connect the GTS to the DLC3.


c.

Turn the ignition switch to ON.


d.

Turn the GTS on.


e.

Enter the following menus: Powertrain / Urea Selective Catalytic Reduction / Trouble Codes.


f.

Read the DTCs.

Result:
Result Proceed to
DTC P248111 is output A
DTCs are not output B




A

8.REPLACE DCU (EMISSION CONTROL ECU ASSEMBLY)

B

END

8.REPLACE DCU (EMISSION CONTROL ECU ASSEMBLY)
a.

Replace the DCU (emission control ECU assembly).

Click hereEngine / Hybrid System>N04C-WA (EMISSION CONTROL)>UREA PUMP CONTROL ECU>REMOVAL


Result:
Proceed to
NEXT



NEXT

14.CLEAR DTC
9.REPAIR OR REPLACE HARNESS OR CONNECTOR
a.

Repair or replace the harness or connector.


Result:
Proceed to
NEXT



NEXT

14.CLEAR DTC
10.REPAIR OR REPLACE HARNESS OR CONNECTOR
a.

Repair or replace the harness or connector.


Result:
Proceed to
NEXT



NEXT

14.CLEAR DTC
11.REPLACE NO. 5 EXHAUST GAS TEMPERATURE SENSOR
a.

Replace the No. 5 exhaust gas temperature sensor.

Click hereEngine / Hybrid System>N04C-WA (EMISSION CONTROL)>EXHAUST GAS TEMPERATURE SENSOR>REMOVAL


Result:
Proceed to
NEXT



NEXT

14.CLEAR DTC
12.REPAIR OR REPLACE NO. 5 EXHAUST GAS TEMPERATURE SENSOR
a.

Clean the sensing part of the No. 5 exhaust gas temperature sensor and correctly install it.

HINT:

If the No. 5 exhaust gas temperature sensor is damaged, replace it.



Result:
Proceed to
NEXT



NEXT

14.CLEAR DTC
13.CONNECT SECURELY
a.

Securely connect the No. 5 exhaust gas temperature sensor connector.

HINT:

Repair parts as necessary.



Result:
Proceed to
NEXT



NEXT

14.CLEAR DTC
14.CLEAR DTC
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Clear the DTCs.

NOTICE:

Clear the DTCs with the engine stopped, as DTCs cannot be cleared while the engine is running.



e.

Turn the ignition switch off and wait for at least 30 seconds.


Result:
Proceed to
NEXT



NEXT

15.CHECK WHETHER DTC OUTPUT RECURS (DTC P248111)
15.CHECK WHETHER DTC OUTPUT RECURS (DTC P248111)
a.

Drive the vehicle in accordance with the driving pattern described in the Confirmation Driving Pattern.


b.

Connect the GTS to the DLC3.


c.

Turn the ignition switch to ON.


d.

Turn the GTS on.


e.

Enter the following menus: Powertrain / Urea Selective Catalytic Reduction / Trouble Codes.


f.

Read the DTCs.

OK:

DTCs are not output



Result:
Proceed to
NEXT



NEXT

END