16400
1.REMOVE RADIATOR ASSEMBLY
35000
2.REMOVE AUTOMATIC TRANSMISSION ASSEMBLY (for Automatic Transmission)
33110
3.REMOVE MANUAL TRANSMISSION ASSEMBLY (for Manual Transmission)
31250
4.REMOVE CLUTCH DISC ASSEMBLY (for Manual Transmission)
17341F
5.REMOVE NO. 1 AIR HOSE
Separate the engine wire.
Disconnect the ventilation hose.
Remove the bolt.
Loosen the 2 No. 1 air cleaner hose clamps and remove the No. 1 air hose.
17201
6.REMOVE TURBOCHARGER SUB-ASSEMBLY
16577C
7.REMOVE RADIATOR PIPE
Remove the 2 bolts and radiator pipe.
88320
8.SEPARATE COOLER COMPRESSOR ASSEMBLY (w/ Air Conditioning System)
Disconnect the connector.
Remove the 6 bolts and separate the cooler compressor assembly.
27020
9.REMOVE GENERATOR ASSEMBLY
44360
10.SEPARATE VANE PUMP OIL RESERVOIR ASSEMBLY
Remove the 3 bolts and vane pump oil reservoir assembly.
53712C
11.REMOVE FRONT FENDER APRON LH
44310
12.SEPARATE VANE PUMP ASSEMBLY
Remove the 2 bolts and separate the vane pump assembly.
Remove the O-ring.
17342P
13.REMOVE NO. 2 AIR HOSE
44774
14.DISCONNECT UNION TO CONNECTOR TUBE HOSE
Disconnect the union to connector tube hose.
23273C
15.DISCONNECT NO.2 FUEL HOSE
Disconnect the No. 2 fuel hose.
22100A
16.DISCONNECT INJECTION PUMP TO FUEL FILTER FUEL HOSE OR PIPE
Disconnect the injection pump to fuel filter fuel hose or pipe.
28100
17.REMOVE STARTER ASSEMBLY
45470
18.SEPARATE TIE ROD ASSEMBLY LH
Remove the cotter pin.
Remove the nut.
Using SST, separate the tie rod end assembly LH from the steering relay rod assembly.
45450
19.SEPARATE STEERING RELAY ROD ASSEMBLY
| *a | for Idler Arm Bracket Assembly Side |
| *b | for Center Arm Bracket Assembly Side |
Remove the 2 cotter pins.
Remove the 2 nuts.
Using SST, separate the steering relay rod assembly from the center arm.
51202D
20.REMOVE FRONT SUSPENSION CROSSMEMBER SUB-ASSEMBLY
Remove the 6 bolts, 4 nuts, 4 washers and front lower suspension crossmember sub-assembly.
While fixing the nut in place, loosen and remove the through bolt.
82121
21.SEPARATE ENGINE WIRE
Separate all engine wires from the engine.
22.REMOVE ENGINE ASSEMBLY
Support the engine using an engine lifter.
Remove the 2 nuts.
Remove the 4 bolts and front No. 1 engine mounting bracket LH.
Remove the engine mounting stabilizer and front engine mounting insulator.
Remove the 2 nuts.
Remove the 4 bolts and front No. 1 engine mounting bracket RH.
Remove the engine mounting stabilizer and front engine mounting insulator.
Remove the engine assembly.
12180E
23.REMOVE OIL FILLER CAP SUB-ASSEMBLY
Remove the oil filler cap sub-assembly.
11201
24.REMOVE CYLINDER HEAD COVER SUB-ASSEMBLY
Remove the 2 bolts, 2 cylinder head cover stay and cylinder head cover sub-assembly.
25625B
25.REMOVE EGR VALVE BRACKET
Remove the 4 bolts and EGR valve bracket.
15301
26.REMOVE OIL DIPSTICK GUIDE
Remove the bolt and oil dipstick guide.
Remove the O-ring from the oil dipstick guide.
16206C
27.REMOVE WATER BY-PASS PIPE SUB-ASSEMBLY
Disconnect the 2 water by-pass hoses from the EGR valve assembly.
Remove the 3 bolts and 2 union bolts, then remove the water by-pass pipe sub-assembly.
17113D
28.REMOVE NO. 1 INTAKE PIPE
11202D
29.REMOVE NO. 2 CYLINDER HEAD COVER SUB-ASSEMBLY
Remove the wire harness.
Remove the 2 cylinder head cover cushion rubber.
Remove the 2 bolts and No. 2 cylinder head cover sub-assembly.
Remove the 4 No. 2 cylinder head cover gaskets.
17113
30.REMOVE NO. 2 INTAKE PIPE
Remove the 4 bolts and No. 2 intake pipe.
23741B
31.REMOVE INJECTION PIPE CLAMP
23670
32.REMOVE INJECTOR ASSEMBLY
17111
33.REMOVE INTAKE MANIFOLD
17141
34.REMOVE EXHAUST MANIFOLD
83530
35.REMOVE ENGINE OIL PRESSURE SWITCH ASSEMBLY
36.REMOVE OIL COOLER COVER SUB-ASSEMBLY
89422
37.REMOVE ENGINE COOLANT TEMPERATURE SENSOR
Using a 19 mm deep socket wrench, remove the water temperature sender gauge assembly.
38.REMOVE CRANKSHAFT POSITION SENSOR
Remove the bolt and crankshaft position sensor.
39.REMOVE CAMSHAFT POSITION SENSOR
Remove the bolt and camshaft position sensor.
16630G
40.REMOVE IDLER PULLEY ASSEMBLY
Remove the 2 bolts and idler pulley assembly.
88440B
41.REMOVE IDLE PULLEY ASSEMBLY WITH BRACKET (w/ Air Conditioning System)
Remove the 3 bolts and idle pulley assembly with bracket.
88431
42.REMOVE NO. 1 COMPRESSOR MOUNTING BRACKET (w/ Air Conditioning System)
Remove the 7 bolts, compressor mounting bracket set and No. 1 compressor mounting bracket.
| *1 | Compressor Mounting Bracket Set |
| *2 | No. 1 Compressor Mounting Bracket |
16331
43.REMOVE WATER OUTLET SUB-ASSEMBLY
Remove the 3 bolts and water outlet sub-assembly.
16331A
44.REMOVE THERMOSTAT
16331
45.REMOVE WATER OUTLET HOUSING
Remove the 3 bolts, water outlet housing and gasket.
87208L
46.REMOVE WATER PIPE SUB-ASSEMBLY
Remove the 3 bolts, water pipe sub-assembly and O-ring.
16206
47.REMOVE NO. 2 WATER BY-PASS PIPE SUB-ASSEMBLY
Disconnect the water hose.
Remove the 2 bolts and No. 2 water by-pass pipe sub-assembly.
16206C
48.REMOVE WATER BY-PASS PIPE SUB-ASSEMBLY
Remove the 6 bolts, 6 O-rings and water by-pass pipe sub-assembly.
16100
49.REMOVE ENGINE WATER PUMP ASSEMBLY
23803H
50.REMOVE FUEL RETURN PIPE SUB-ASSEMBLY
23811
51.REMOVE FUEL FILTER TO INJECTION PUMP FUEL PIPE
19971E
52.REMOVE VACUUM PIPE
Remove the nut and pipe clamp.
Remove the union bolt, vacuum pipe and 2 gaskets.
29601B
53.REMOVE VACUUM PUMP OIL PIPE SUB-ASSEMBLY
29300
54.REMOVE VACUUM PUMP ASSEMBLY
55.REMOVE NO. 3 NOZZLE LEAKAGE PIPE SUB-ASSEMBLY
Loosen the hose clamp, 2 union bolts, 2 gaskets and the No. 3 nozzle leakage pipe sub-assembly.
23810A
56.REMOVE COMMON RAIL ASSEMBLY
Remove the 2 bolts and common rail assembly.
82702E
57.REMOVE WIRING HARNESS BRACKET
Remove the 2 bolts and wiring harness bracket.
23849G
58.REMOVE FUEL SUPPORT
Remove the 2 bolts and fuel support.
Remove the 2 bolts and fuel support.
22100
59.REMOVE INJECTION OR SUPPLY PUMP ASSEMBLY
Remove the 4 bolts and injection or supply pump assembly.