Home › Engine / Hybrid System › N04C-VJ (ENGINE CONTROL) › ECD SYSTEM › from 2021.01
RM2850E _51 Engine / Hybrid System _096807 N04C-VJ ENGINE CONTROL _0454116 ECD SYSTEM J

N04C-VJ ENGINE CONTROL  ECD SYSTEM  Lack of Power or Hesitation  


DESCRIPTION

Malfunction Condition Main Trouble Areas Related Trouble Areas
·

Lack of power caused by abnormal fuel injection volume (supply pump malfunction or injector malfunction)

·

Lack of power caused by intake air volume shortage (turbocharger malfunction, front exhaust pipe or exhaust manifold converter blocked)


1.

Injector assembly malfunctions

-

Injector assembly sliding malfunction

-

Injector assembly stuck closed

-

Injector assembly stuck open

-

Deposits in injector assembly

-

Injector assembly circuit malfunction


2.

Abnormal common rail pressure

-

Injection or supply pump assembly


3.

Abnormal intake air volume

-

Turbocharger sub-assembly

-

Front exhaust pipe blockage

-

Center exhaust pipe assembly (catalytic converter) blockage



·

Pressure limiter (built into common rail assembly)

·

Intake air system leak

·

Intake air system blockage

·

EGR system

·

Fuel filter element is clogged

·

Throttle valve

·

Compression pressure

·

Injector compensation code

·

Fuel leak

·

Fuel pressure sensor (built into common rail assembly)

·

Injector driver assembly

·

Vehicle modifications

·

Low quality fuel

·

Frozen fuel

·

ECM



HINT:
·

Specified values in the following troubleshooting flowchart are for reference only. Variations in the Data List values may occur depending on the measuring conditions or the vehicle's age. Do not judge the vehicle to be normal even when the Data List values indicate a standard level. There are possibly some concealed factors of the malfunction.

·

Check that the vehicle has not been modified in any way prior to the vehicle inspection.

·

This troubleshooting procedure checks for the cause of an obvious lack of engine power (the vehicle speed does not reach the target speed in the high speed range) while the vehicle is being driven.



CAUTION / NOTICE / HINT

NOTICE:
·

After replacing the ECM, the new ECM needs registration (Click here Engine / Hybrid System>N04C-VJ (ENGINE CONTROL)>ECD SYSTEM>REGISTRATION) and initialization (Click here Engine / Hybrid System>N04C-VJ (ENGINE CONTROL)>ECD SYSTEM>INITIALIZATION).

·

After replacing the injection or supply pump assembly, the ECM needs initialization (Click here Engine / Hybrid System>N04C-VJ (ENGINE CONTROL)>ECD SYSTEM>INITIALIZATION).

·

After replacing the injector assembly, the ECM needs registration (Click here Engine / Hybrid System>N04C-VJ (ENGINE CONTROL)>ECD SYSTEM>REGISTRATION).



HINT:

Before troubleshooting, conduct the following:

1.

Check the fuel quality.

2.

Check the fuel for air.

3.

Check the fuel system for blockages.

4.

Check the air filter.

5.

Check the engine oil.

6.

Check the engine coolant.

7.

Check the engine idling speed and the maximum engine speed.

8.

Check the vacuum pump.



PROCEDURE

1.CHECK HARNESS AND CONNECTOR IN ENGINE ROOM
a.

Check the wire harness and connector connections of the common rail system components.

HINT:

Check the following components and systems:

·

Sensors

·

Injection or supply pump assembly

·

Common rail assembly

·

Injector assemblies

·

Injector driver assembly

·

Turbocharger system

·

Intake and exhaust system



OK:

The wire harnesses and connectors are connected securely.



Result:
Proceed to
OK
NG



OK

2.PERFORM CONFIRMATION DRIVING PATTERN

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

2.PERFORM CONFIRMATION DRIVING PATTERN
HINT:

Drive the vehicle according to the driving pattern below to allow the ECM to set DTCs relating to malfunctions of the fuel system, EGR system and throttle valve. If DTCs are set, problem areas can be identified.



b.

Fully warm up the engine.


c.

Allow the engine to idle for 5 minutes or more.


d.

Drive the vehicle at more than 40 km/h (25 mph) for 1 minute or more (Procedure "A").


e.

Decelerate and stop the vehicle (Procedure "B").


f.

Repeat steps "A" (See procedure "A") and "B" (See procedure "B") 4 times or more.


g.

Stop the engine and wait for at least 10 seconds (Procedure "C").


h.

Repeat steps "A" (See procedure "A") and "C" (See procedure "C") described above (to set DTCs relating to the EGR system and throttle valve).


i.

Drive the vehicle at more than 70 km/h (43 mph) for at least 1 minute (to set DTCs relating to the supply pump).


Result:
Proceed to
NEXT



NEXT

3.CHECK DTC OUTPUT (RELATING TO ENGINE)
3.CHECK DTC OUTPUT (RELATING TO ENGINE)
a.

Enter the following menus: Powertrain / Engine and ECT / DTC.


b.

Read the DTCs.


Result:
Result Proceed to
No DTCs A
Engine related DTCs B



A

4.PERFORM ACTIVE TEST USING GTS (TEST THE FUEL LEAK)

B

4.PERFORM ACTIVE TEST USING GTS (TEST THE FUEL LEAK)
HINT:

By performing this Active Test, the engine speed is maintained at 2000 rpm and the common rail internal fuel pressure is raised to the maximum operating pressure. As a result, a fuel leak check can be conducted while retaining the high common rail pressure.


a.

Connect the GTS to the DLC3.


b.

Start the engine.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine and ECT / Active Test / Test the Fuel Leak.


e.

Visually check the injection or supply pump assembly, injector assembly and fuel line located between the injection or supply pump assembly and common rail assembly for fuel leaks and fuel pressure leaks. Also, perform the same check on the fuel line between the common rail assembly and the injector assembly.

HINT:

There may be fuel leaks inside the components, such as the injection or supply pump assembly.


OK:

No fuel leak.



Result:
Proceed to
OK
NG



OK

5.CHECK WHITE SMOKE

NG

REPAIR OR REPLACE FUEL LEAK POINT

5.CHECK WHITE SMOKE
a.

Rev up the engine from idling to 3000 rpm several times to check whether white smoke is emitted from the exhaust pipe.


b.

Check that the intake system pipes and hoses are not excessively contaminated with oil. If white smoke is emitted from the intake system, its pipes and hoses are excessively contaminated with oil. If the presence of white smoke in the exhaust gas is confirmed, there is a high possibility of mechanical problems in the turbocharger sub-assembly or engine assembly.


Result:
Result Proceed to
No problems described above A
White smoke emitted, or intake system pipes and hoses excessively contaminated with oil B



A

6.READ VALUE USING GTS (MAF AND FUEL PRESS)

B

28.INSPECT TURBOCHARGER SUB-ASSEMBLY (PRESSURE)
6.READ VALUE USING GTS (MAF AND FUEL PRESS)
a.

Connect the GTS to the DLC3.


b.

Start the engine, and warm it up.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine and ECT / Data List.


e.

Enter the following menus in order and read the values.

·

MAF

·

Fuel Press


Standard:
Item Engine Speed * Standard Range Description
MAF Idling 4 to 15 gm/s Intake air volume detected by mass air flow meter sub-assembly
3000 rpm (no engine load) 80 to 90 gm/s
Fuel Pressure Idling 20000 to 30000 kPa Common rail assembly internal fuel pressure


Result:
Item Result Proceed to
MAF, and Fuel press Standard range A
Only MAF Outside standard range B
Only Fuel Press Outside standard range C


HINT:

*: The A/C switch and all accessory switches should be off, and the engine should be fully warmed up.




A

7.READ VALUE USING GTS (INJECTION FEED BACK VAL AND INJECTION VOLUME)

B

24.INSPECT EGR VALVE ASSEMBLY

C

32.CHECK AND REPLACE FUEL FILTER ASSEMBLY
7.READ VALUE USING GTS (INJECTION FEED BACK VAL AND INJECTION VOLUME)
a.

Select the following menu items in order and read the values.

·

Injection Feedback Val #1, #2, #3, and #4

·

Injection Volume


Standard:
Item Engine Speed* Standard Range Description
Injection Feedback Val #1 Idling -7.0 to 7.0 mm3/st Value of injector fuel injection volume compensates for differences in combustion condition of cylinders
·

Positive values indicate control which corrects combustion degradation

·

Negative values indicate control which corrects excessive combustion pressure

·

If problems exist, Injection Feedback Val may deviate from -7.0 and 7.0 mm3/st range


Injection Feedback Val #2 Idling -7.0 to 7.0 mm3/st
Injection Feedback Val #3 Idling -7.0 to 7.0 mm3/st
Injection Feedback Val #4 Idling -7.0 to 7.0 mm3/st
Injection Volume Idling 5.0 to 12.0 mm3/st Fuel injection volume value controlled by ECU
·

Controls NE signal, fuel temperature, engine coolant temperature, intake air temperature, atmospheric pressure, and EGR volume.

·

If problems exist, Injection Volume may be outside standard range




Result:
Result Proceed to
Standard range A
Injection Feedback Val #1 to #4 and/or Injection Volume outside standard range B


HINT:

*: The A/C switch and all accessory switches should be off, and the engine should be fully warmed up.




A

8.CHECK INJECTOR COMPENSATION CODE

B

14.IDENTIFY MALFUNCTIONING CYLINDER INJECTOR
8.CHECK INJECTOR COMPENSATION CODE
a.

Read the injector compensation code (Click here Engine / Hybrid System>N04C-VJ (ENGINE CONTROL)>ECD SYSTEM>PRECAUTION).

HINT:

If the injector compensation code is not correctly registered, it may cause malfunctions (Click here Engine / Hybrid System>N04C-VJ (ENGINE CONTROL)>ECD SYSTEM>REGISTRATION).



b.

Check the injector compensation code.

OK:

Compensation code of the installed injector assembly is same as the code registered in the ECM.



Result:
Proceed to
OK
NG



OK

9.RESET ECM

NG

PERFORM REGISTER INJECTOR COMPENSATION CODE

9.RESET ECM
a.

Disconnect the cable from the negative (-) battery terminal for at least 2 minutes.


b.

Reconnect the cable to the negative (-) battery terminal.


c.

Check whether the malfunction has been successfully repaired by performing a driving test.

OK:

Malfunction has been repaired successfully.



Result:
Proceed to
OK
NG



OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

10.BLEED AIR FROM FUEL SYSTEM
10.BLEED AIR FROM FUEL SYSTEM
a.

To bleed air from the priming pump, pump the priming pump until it becomes hard and cannot be pumped any more.


Result:
Proceed to
NEXT



NEXT

11.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
11.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
a.

Check whether the malfunction has been successfully repaired by performing a driving test.

OK:

Malfunction has been repaired successfully.



Result:
Proceed to
OK
NG



OK

END

NG

12.CHECK INTAKE SYSTEM
12.CHECK INTAKE SYSTEM
a.

Check for air leaks and blockage between the air cleaner and turbocharger sub-assembly.


b.

Check for air leaks and blockage between the turbocharger sub-assembly and intake manifold.

OK:

No leaks or blockage.



Result:
Proceed to
NEXT



NEXT

13.INSPECT TURBOCHARGER SUB-ASSEMBLY (PRESSURE)
13.INSPECT TURBOCHARGER SUB-ASSEMBLY (PRESSURE)
a.

Result:
Proceed to
OK
NG



OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

REPLACE TURBOCHARGER SUB-ASSEMBLY

14.IDENTIFY MALFUNCTIONING CYLINDER INJECTOR
a.

Follow the instructions in the table below according to the check result of the GTS.

HINT:

This operation is based on the premise that the common rail pressure is normal.


Standard:
Item Engine Speed*1 Reference Value
Injection Feedback Val #1 to #4 Idling -7.0 to 7.0 mm3/st
Injection Volume Idling 5.0 to 12.0 mm3/st


HINT:

*1: The A/C switch and all accessory switches should be off, and the engine should be fully warmed up.


Injection volume Injection volume
Injection Feedback Val #1 to #4 Less than 5.0 mm3/st Between 5.0 and 19.0 mm3/st (Normal) More than 19.0 mm3/st
7.0 mm3/st or more, -7.0 mm3/st or less A B B
Between -7.0 and 7.0 mm3/st - Normal C*2

Result:
Proceed to Inspection Areas Descriptions
A Inspect and repair cylinder injector with revised injection volume of less than -7.0 mm3/st:
·

Perform power balance inspection and identify malfunctioning cylinder

·

Replace malfunctioning cylinder injector


Abnormal value cylinder injector injects excessively large quantity of fuel
B Identify malfunctioning cylinders by conducting power balance inspection:
·

Perform power balance inspection to identify malfunctioning cylinders

·

Clean malfunctioning cylinder injector, then check and repair it


Abnormal value cylinder injector injects excessively large quantity of fuel:
·

Fuel injection volume too low due to injector nozzle being blocked by deposits

·

Abnormal value cylinder injector compression decreases

·

Abnormal value cylinder injector injects excessively large quantity of fuel


C Inspect and repair all cylinder injectors:
Clean all cylinder injectors, and then inspect and repair them
All cylinder injectors inject excessively small quantity of fuel:
Fuel injection volume too low due to all cylinder injector nozzles being blocked by deposits


HINT:

*2: When the Injection Volume displayed on the GTS is large despite the Fuel Press and Injection Feedback Val #1 to #4 in the Data List being normal, the injector assembly may be clogged. In this case, there may be deposits inside or outside the injector assembly.

·

Despite the injector assembly functioning normally, the indicated Injection Feedback Val #1 to #4 value may be outside the normal operating range due to compensation for other problems (such as low compression).

·

Injection Feedback Val #1 to #4 is the value used to correct the fuel injection volumes of each cylinder, in order to optimize (compensate for the unevenness between) all the cylinder combustion conditions. If any of the cylinders malfunction, the fuel injection volumes for the normal cylinders are corrected simultaneously. As a result, the Injection Feedback Val #1 to #4 may deviate from the standard range.





A

15.PERFORM ACTIVE TEST USING GTS (CONTROL THE CYLINDER #1 TO #4 FUEL CUT)

B

16.PERFORM ACTIVE TEST USING GTS (CONTROL THE CYLINDER #1 TO #4 FUEL CUT)

C

21.CHECK ALL CYLINDER INJECTION FOR DEPOSITS
15.PERFORM ACTIVE TEST USING GTS (CONTROL THE CYLINDER #1 TO #4 FUEL CUT)
HINT:

Use this Active Test to determine the malfunctioning cylinder.


a.

Connect the GTS to the DLC3.


b.

Start the engine.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the Cylinder #1 to #4 Fuel Cut.

HINT:
·

If the engine idle speed does not change when a fuel injector is disabled, the cylinder being tested is malfunctioning.

·

If the cylinder being tested is normal, there will be a significant change in idle speed when the fuel injection is stopped for that cylinder.




Result:
Proceed to
NEXT



NEXT

REPLACE INJECTOR ASSEMBLY OF MALFUNCTIONING CYLINDER

16.PERFORM ACTIVE TEST USING GTS (CONTROL THE CYLINDER #1 TO #4 FUEL CUT)
HINT:

Use this Active Test to determine the malfunctioning cylinder.


a.

Connect the GTS to the DLC3.


b.

Start the engine.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the Cylinder #1 to #4 Fuel Cut.

HINT:
·

If the engine idle speed does not change when a fuel injector is disabled, the cylinder being tested is malfunctioning.

·

If the cylinder being tested is normal, there will be a significant change in idle speed when the fuel injection is stopped for that cylinder.




Result:
Proceed to
NEXT



NEXT

17.CHECK CYLINDER COMPRESSION PRESSURE
17.CHECK CYLINDER COMPRESSION PRESSURE
a.

Check the cylinder compression pressure (Click here Engine / Hybrid System>N04C-VJ (ENGINE MECHANICAL)>ENGINE>ON-VEHICLE INSPECTION).


Result:
Proceed to
OK
NG



OK

18.CHECK MALFUNCTIONING CYLINDER INJECTION FOR DEPOSITS

NG

CHECK ENGINE TO DETERMINE CAUSE OF LOW COMPRESSION

18.CHECK MALFUNCTIONING CYLINDER INJECTION FOR DEPOSITS
HINT:

If an injector assembly is contaminated with deposits, the fuel injection volume deviates from the standard range. This may cause malfunctions.


a.

Check the injector assembly for any deposits.


Result:
Result Proceed to
Deposits A
No deposits B



A

19.CLEAN INJECTOR ASSEMBLY

B

REPLACE INJECTOR ASSEMBLY OF MALFUNCTIONING CYLINDER

19.CLEAN INJECTOR ASSEMBLY
a.

Wipe away deposits from the tips of the injector assemblies.

HINT:
·

Solvent or carbon removal agents help remove deposits easily.

·

Exercise extreme care not to damage the injector assemblies while wiping off the deposits.




Result:
Proceed to
NEXT



NEXT

20.READ VALUE USING GTS (INJECTION FEEDBACK VAL AND INJECTION VOLUME)
20.READ VALUE USING GTS (INJECTION FEEDBACK VAL AND INJECTION VOLUME)
a.

Reinstall the injector assembly to the cylinder head.


b.

Connect the GTS to the DLC3.


c.

Turn the ignition switch to ON.


d.

Turn the GTS on.


e.

Start the engine and warm it up.


f.

Enter the following menus: Powertrain / Engine and ECT / Data List.


g.

Enter the following menus in order and read the values.

·

Injection Feedback Val #1, #2, #3, and #4

·

Injection Volume


Standard:
Item Engine Speed* Reference Value
Injection Feedback Val #1 to #4 Idling -7.0 to 7.0 mm3/st
Injection Volume Idling 5.0 to 12.0 mm3/st


HINT:

*: The A/C switch and all accessory switches should be off, and the engine should be fully warmed up. When the values are outside the standard range, deposits inside the injector assembly may be causing the problem.


OK:

Values are within the standard range.



Result:
Proceed to
OK
NG



OK

END

NG

REPLACE INJECTOR ASSEMBLY OF MALFUNCTIONING CYLINDER

21.CHECK ALL CYLINDER INJECTION FOR DEPOSITS
HINT:

If an injector assembly is contaminated with deposits, the fuel injection volume deviates from the standard range. This may cause malfunctions.


a.

Check the injector assembly for any deposits.


Result:
Result Proceed to
Deposits A
No deposits B



A

22.CLEAN INJECTOR ASSEMBLY

B

REPLACE ALL CYLINDER INJECTOR ASSEMBLY

22.CLEAN INJECTOR ASSEMBLY
a.

Wipe away deposits from the tips of the injector assemblies.

HINT:
·

Solvent or carbon removal agents help remove deposits easily.

·

Exercise extreme care not to damage the injector assemblies while wiping off the deposits.




Result:
Proceed to
NEXT



NEXT

23.READ VALUE USING GTS (INJECTION FEEDBACK VAL AND INJECTION VOLUME)
23.READ VALUE USING GTS (INJECTION FEEDBACK VAL AND INJECTION VOLUME)
a.

Reinstall the injector assembly to the cylinder head.


b.

Connect the GTS to the DLC3.


c.

Turn the ignition switch to ON.


d.

Turn the GTS on.


e.

Start the engine and warm it up.


f.

Enter the following menus: Powertrain / Engine and ECT / Data List.


g.

Enter the following menus in order and read the values.

·

Injection Feedback Val #1, #2, #3, and #4

·

Injection Volume


Standard:
Item Engine Speed* Reference Value
Injection Feedback Val #1 to #4 Idling -7.0 to 7.0 mm3/st
Injection Volume #1 to #4 Idling 5.0 to 12.0 mm3/st


HINT:

*: The A/C switch and all accessory switches should be off, and the engine should be fully warmed up. When the values are outside the standard range, deposits inside the injector assembly may be causing the problem.


OK:

Values are within the standard range.



Result:
Proceed to
OK
NG



OK

END

NG

REPLACE ALL CYLINDER INJECTOR ASSEMBLY

24.INSPECT EGR VALVE ASSEMBLY

Result:
Proceed to
OK
NG



OK

25.INSPECT DIESEL THROTTLE BODY ASSEMBLY

NG

25.INSPECT DIESEL THROTTLE BODY ASSEMBLY
a.

Result:
Proceed to
OK
NG



OK

26.CHECK INTAKE SYSTEM

NG

26.CHECK INTAKE SYSTEM
a.

Check for air leaks and blockage between the air cleaner and turbocharger sub-assembly.


b.

Check for air leaks and blockage between the turbocharger sub-assembly and intake manifold.

OK:

No leaks or blockage.



Result:
Proceed to
OK
NG



OK

27.INSPECT EXHAUST RETARDER ASSEMBLY

NG

REPAIR OR REPLACE MALFUNCTIONING PARTS

27.INSPECT EXHAUST RETARDER ASSEMBLY
a.

Inspect the exhaust retarder assembly.


Result:
Proceed to
OK
NG



OK

28.INSPECT TURBOCHARGER SUB-ASSEMBLY (PRESSURE)

NG

REPLACE EXHAUST RETARDER ASSEMBLY

28.INSPECT TURBOCHARGER SUB-ASSEMBLY (PRESSURE)
a.

Result:
Proceed to
OK
NG



OK

29.READ VALUE USING GTS (MAF)

NG

REPLACE TURBOCHARGER SUB-ASSEMBLY

29.READ VALUE USING GTS (MAF)
a.

Connect the GTS to the DLC3.


b.

Start the engine, and warm it up.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine and ECT / Data List.


e.

Enter the following menus in order and read the values.

·

MAF


Standard:
Item Engine Speed * Standard Range Description
MAF Idling 4 to 15 gm/s Intake air volume detected by mass air flow meter sub-assembly
3000 rpm (no engine load)Idling 80 to 90 gm/s


HINT:

*: The A/C switch and all accessory switches should be off, and the engine should be fully warmed up.


OK:

The values are within the standard range.



Result:
Proceed to
OK
NG



OK

END

NG

30.REPLACE CENTER EXHAUST PIPE ASSEMBLY
30.REPLACE CENTER EXHAUST PIPE ASSEMBLY
Result:
Proceed to
NEXT



NEXT

31.READ VALUE USING GTS (MAF)
31.READ VALUE USING GTS (MAF)
a.

Connect the GTS to the DLC3.


b.

Start the engine and warm it up.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine and ECT / Data List.


e.

Enter the following menus in order and read the values.

·

MAF


Standard:
Item Engine Speed * Standard Range Description
MAF Idling 4 to 15 gm/s Intake air volume detected by mass air flow meter sub-assembly
3000 rpm (no engine load) 80 to 90 gm/s


HINT:

*: The A/C switch and all accessory switches should be off, and the engine should be fully warmed up.


OK:

The values are within the standard range.



Result:
Proceed to
OK
NG



OK

END

NG

REPLACE TURBOCHARGER SUB-ASSEMBLY

32.CHECK AND REPLACE FUEL FILTER ASSEMBLY
Result:
Proceed to
NEXT



NEXT

33.READ VALUE USING GTS (FUEL PRESS)
33.READ VALUE USING GTS (FUEL PRESS)
a.

Connect the GTS to the DLC3.


b.

Start the engine and warm it up.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine and ECT / Data List.


e.

Enter the following menus and read the values.

·

Fuel Press


Standard:
Item Engine Speed* Reference Value
Fuel Press Idling 20000 to 30000 kPa


HINT:

*: The A/C switch and all accessory switches should be off, and the engine should be fully warmed up.


OK:

The values are within the standard range.



Result:
Proceed to
OK
NG



OK

END

NG

34.INSPECT COMMON RAIL ASSEMBLY (FUEL PRESSURE SENSOR)
34.INSPECT COMMON RAIL ASSEMBLY (FUEL PRESSURE SENSOR)
a.

Inspect the fuel pressure sensor connector.

Click hereEngine / Hybrid System>N04C-VJ (FUEL)>COMMON RAIL>INSPECTION


Result:
Proceed to
OK
NG



OK

35.INSPECT INJECTION OR SUPPLY PUMP ASSEMBLY

NG

REPLACE COMMON RAIL ASSEMBLY

35.INSPECT INJECTION OR SUPPLY PUMP ASSEMBLY
a.
A341337C01
0.094,0.073 0.406,0.271 0.313,0.198 10 false *1 0.792,0.448 1.104,0.646 0.313,0.198 10 false *2
*1 Component without harness connected
(Injection or Supply Pump Assembly)
*2 Suction Control Valve


Disconnect the suction control valve connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1 - 2 20°C (68°F) 2.0 to 2.2 Ω



c.

Reconnect the suction control valve connector.


Result:
Proceed to
OK
NG



OK

36.READ VALUE USING GTS (TARGET PUMP SCV CURRENT)

NG

REPLACE INJECTION OR SUPPLY PUMP ASSEMBLY

36.READ VALUE USING GTS (TARGET PUMP SCV CURRENT)
a.

Connect the GTS to the DLC3.


b.

Start the engine.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine and ECT / Data List / Target Pump SCV Current.


e.

Read the value.

Standard:
Engine Speed Result
Idling 1350 to 2200 mA



Result:
Proceed to
OK
NG



OK

CHECK AND REPLACE COMMON RAIL ASSEMBLY (PRESSURE LIMITER)

NG

REPLACE INJECTION OR SUPPLY PUMP ASSEMBLY