Home › Engine / Hybrid System › 2GR-FE ENGINE CONTROL › SFI SYSTEM › 2013.04–2014.09
RM24M0E _51 Engine / Hybrid System _059540 2GR-FE ENGINE CONTROL _0291770 SFI SYSTEM C

2GR-FE ENGINE CONTROL  SFI SYSTEM  P0171  System Too Lean (Bank 1)  P0172  System Too Rich (Bank 1)  P0174  System Too Lean (Bank 2)  P0175  System Too Rich (Bank 2)  


DESCRIPTION

The fuel trim is related to the feedback compensation value, not to the basic injection duration. The fuel trim consists of both the short-term and long-term fuel trims.

The short-term fuel trim is fuel compensation that is used to constantly maintain the air fuel ratio at stoichiometric levels. The signal from the air fuel ratio sensor indicates whether the air fuel ratio is rich or lean compared to the stoichiometric ratio. This triggers a reduction in the fuel injection volume if the air fuel ratio is rich and an increase in the fuel injection volume if lean.

Factors such as individual engine differences, wear over time and changes in operating environment cause short-term fuel trim to vary from the central value. The long-term fuel trim, which controls overall fuel compensation, compensates for long-term deviations in the fuel trim from the central value caused by the short-term fuel trim compensation.

DTC No. DTC Detection Conditions Trouble Area
P0171
P0174
With a warm engine and stable air fuel ratio feedback, the fuel trim is considerably in error to the lean side (2 trip detection logic).
·

Intake system

·

Fuel injector assembly blockage

·

Mass air flow meter sub-assembly

·

Engine coolant temperature sensor

·

Fuel pressure

·

Gas leak from exhaust system

·

Open or short in air fuel ratio sensor (bank 1, 2 sensor 1) circuit

·

Air fuel ratio sensor (bank 1, 2 sensor 1)

·

PCV valve and hose

·

PCV hose connections

·

Wire harness or connector

·

ECM


P0172
P0175
With a warm engine and stable air fuel ratio feedback, the fuel trim is considerably in error to the rich side (2 trip detection logic).
·

Fuel injector assembly leak or blockage

·

Mass air flow meter sub-assembly

·

Engine coolant temperature sensor

·

Ignition system

·

Fuel pressure

·

Gas leak from exhaust system

·

Open or short in air fuel ratio sensor (bank 1, 2 sensor 1) circuit

·

Air fuel ratio sensor (bank 1, 2 sensor 1)

·

Wire harness or connector

·

ECM



HINT:
·

When DTC P0171 or P0174 is stored, the actual air fuel ratio is on the lean side. When DTC P0172 or P0175 is stored, the actual air fuel ratio is on the rich side.

·

If the vehicle runs out of fuel, the air fuel ratio is lean and DTC P0171 or P0174 may be stored. The MIL is then illuminated.

·

When the total of the short-term and long-term fuel trim values is within the malfunction threshold (and the engine coolant temperature is higher than 75°C [167°F]), the system is functioning normally.



MONITOR DESCRIPTION

Under closed loop fuel control, fuel injection volumes that deviate from those estimated by the ECM cause changes in the long-term fuel trim compensation value. The long-term fuel trim is adjusted when there are persistent deviations in the short-term fuel trim values. Deviations from the fuel injection volumes estimated by the ECM also affect the average fuel trim learned value, which is a combination of the average short-term fuel trim (fuel feedback compensation value) and the average long-term fuel trim (learned value of the air fuel ratio). If the average fuel trim learned value exceeds the malfunction thresholds, the ECM interprets this as a fault in the fuel system and stores a DTC.

Example:

The average fuel trim learned value is 35% or higher, or -35% or less, the ECM interprets this as a fuel system malfunction.

A316556E35
2.292,1.958 2.646,1.958 false 2.292,3.073 2.646,3.073 false 1.5,1.865 1.906,1.958 false 1.49,3.021 1.938,3.073 false 2.26,0.385 3.479,0.771 1.219,0.385 10 false Fuel Compensation Amount 1.948,1.865 2.563,2.063 0.615,0.198 10 false 1.35 1.99,3.01 2.375,3.25 0.385,0.24 10 false 0.65 1.979,2.438 2.594,2.635 0.615,0.198 10 false 1.0 0.125,1.146 1.292,1.365 1.167,0.219 10 false P0171 or P0174 0.292,1.531 1.458,2.104 1.167,0.573 10 false +35%: Malfunction Threshold of Lean Condition 0.125,2.625 1.229,2.813 1.104,0.188 10 false P0172 or P0175 0.292,2.917 1.458,3.49 1.167,0.573 10 false -35%: Malfunction Threshold of Rich Condition

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following inspection procedure.


HINT:
·

Bank 1 refers to the bank that includes the No. 1 cylinder*.

*: The No. 1 cylinder is the cylinder which is farthest from the transaxle.

·

Bank 2 refers to the bank that does not include the No. 1 cylinder.

·

Sensor 1 refers to the sensor closest to the engine assembly.

·

Sensor 2 refers to the sensor farthest away from the engine assembly.

·

Read freeze frame data using the intelligent tester. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can be helpful in determining whether the vehicle was running or stopped, whether the engine was warmed up or not, whether the air-fuel ratio was lean or rich, as well as other data recorded at the time of a malfunction.

·

A low air fuel ratio sensor voltage could be caused by a rich air fuel mixture. Check for conditions that would cause the engine to run rich.

·

A high air fuel ratio sensor voltage could be caused by a lean air fuel mixture. Check for conditions that would cause the engine to run lean.



PROCEDURE

1.CHECK ANY OTHER DTCS OUTPUT (IN ADDITION TO DTC P0171, P0172, P0174 OR P0175)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the engine switch on (IG).


c.

Turn the tester on.


d.

Enter the following menus: Powertrain / Engine / DTC.


e.

Read the DTCs.

Result
Result Proceed to
DTC P0171, P0172, P0174 or P0175 is output A
DTC P0171, P0172, P0174 or P0175 and other DTCs are output B

HINT:

If any DTCs other than P0171, P0172, P0174 or P0175 are output, troubleshoot those DTCs first.




A

2.CHECK PCV HOSE CONNECTIONS

B

2.CHECK PCV HOSE CONNECTIONS
a.

Check the PCV hose connections.

OK:

PCV valve and hose are connected correctly and are not damaged.




OK

3.CHECK INTAKE SYSTEM

NG

REPAIR OR REPLACE PCV HOSE

3.CHECK INTAKE SYSTEM
a.

Check the intake system for vacuum leaks.

OK:

No leaks in the intake system.




OK

4.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (CONTROL THE INJECTION VOLUME FOR A/F SENSOR)

NG

REPAIR OR REPLACE INTAKE SYSTEM

4.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (CONTROL THE INJECTION VOLUME FOR A/F SENSOR)
a.

Connect the intelligent tester to the DLC3.


b.

Start the engine.


c.

Turn the tester on.


d.

Warm up the engine and run the engine at an engine speed of 2500 rpm for approximately 90 seconds.


e.

Enter the following menus: Powertrain / Engine / Active Test / Control the Injection Volume for A/F Sensor / All Data / AFS Voltage B1S1 and O2S B1S2 or AFS Voltage B2S1 and O2S B2S2.


f.

Perform the Control the Injection Volume for A/F Sensor operation with the engine idling (press the RIGHT or LEFT button to change the fuel injection volume).


g.

Monitor the voltage outputs of the air fuel ratio sensor and the heated oxygen sensor (AFS Voltage B1S1 and O2S B1S2 or AFS Voltage B2S1 and O2S B2S2) displayed on the tester.

HINT:
·

The Control the Injection Volume for A/F Sensor operation lowers the fuel injection volume by 12.5% or increases the injection volume by 12.5%.

·

The air fuel ratio sensor has an output delay of a few seconds and the heated oxygen sensor has a maximum output delay of approximately 20 seconds.

·

If the sensor output voltage does not change (almost no reaction) while performing the Active Test, the sensor may be malfunctioning.



Standard:
Tester Display
(Sensor)
Injection Volume Status Voltage
AFS Voltage B1S1
AFS Voltage B2S1
(Air fuel ratio)
12.5% Rich Below 3.1 V
-12.5% Lean Higher than 3.4 V
O2S B1S2
O2S B2S2
(Heated oxygen)
12.5% Rich Higher than 0.55 V
-12.5% Lean Below 0.4 V


Result
Status
AFS Voltage B1S1 or AFS Voltage B2S1
Status
O2S B1S2 or O2S B2S2
Air Fuel Ratio Condition and
Air Fuel Ratio Sensor Condition
Suspected Trouble Area Proceed to
Lean/Rich Lean/Rich Normal - A
Lean Lean Actual air fuel ratio lean
·

PCV valve and hose

·

PCV hose connections

·

Fuel injector assembly blockage

·

Gas leak from exhaust system

·

Intake system

·

Fuel pressure

·

Mass air flow meter sub-assembly

·

Engine coolant temperature sensor


A
Rich Rich Actual air fuel ratio rich
·

Fuel injector assembly leak or blockage

·

Gas leak from exhaust system

·

Ignition system

·

Fuel pressure

·

Mass air flow meter sub-assembly

·

Engine coolant temperature sensor


A
Lean Lean/Rich Air fuel ratio sensor malfunction
·

Air fuel ratio sensor


B
Rich Lean/Rich Air fuel ratio sensor malfunction
·

Air fuel ratio sensor


B

Lean: During Control the Injection Volume for A/F Sensor, the air fuel ratio sensor output voltage (AFS Voltage B1S1 or AFS Voltage B2S1) is consistently higher than 3.4 V, and the heated oxygen sensor output voltage (O2S B1S2 or O2S B2S2) is consistently below 0.4 V.

Rich: During Control the Injection Volume for A/F Sensor, the AFS Voltage B1S1 or AFS Voltage B2S1 is consistently below 3.1 V, and the O2S B1S2 or O2S B2S2 is consistently higher than 0.55 V.

Lean/Rich: During Control the Injection Volume for A/F Sensor of the Active Test, the output voltage of the heated oxygen sensor alternates correctly.


HINT:

Refer to "Data List / Active Test" [AFS Voltage B1S1, AFS Voltage B2S1, O2S B1S2 and O2S B2S2] (See page Engine / Hybrid System>2GR-FE ENGINE CONTROL>SFI SYSTEM>DATA LIST / ACTIVE TEST).




A

5.READ VALUE USING INTELLIGENT TESTER (COOLANT TEMP)

B

11.INSPECT AIR FUEL RATIO SENSOR (HEATER RESISTANCE)
5.READ VALUE USING INTELLIGENT TESTER (COOLANT TEMP)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the engine switch on (IG).


c.

Turn the tester on.


d.

Enter the following menus: Powertrain / Engine / Data List / All Data / Coolant Temp.


e.

Read the Data List twice, when the engine is both cold and warmed up.

Standard:
Tester Display Condition Specified Condition
Coolant Temp Cold engine Same as ambient air temperature
Warm engine Between 75 and 100°C (167 and 212°F)




OK

6.READ VALUE USING INTELLIGENT TESTER (MAF)

NG

6.READ VALUE USING INTELLIGENT TESTER (MAF)
a.

Connect the intelligent tester to the DLC3.


b.

Start the engine.


c.

Turn the tester on.


d.

Enter the following menus: Powertrain / Engine / Data List / All Data / MAF, Coolant Temp and Engine Speed.


e.

Allow the engine to idle until Coolant Temp reaches 75°C (167°F) or higher.


f.

Read MAF with the engine speed at 2500 rpm.

Standard:
Tester Display Condition Specified Condition
MAF Shift lever position: N
A/C: Off
Engine Speed: 2500 rpm
Between 8 gm/sec and 19 gm/sec




OK

7.CHECK FUEL PRESSURE

NG

16.CHECK HARNESS AND CONNECTOR (MASS AIR FLOW METER SUB-ASSEMBLY CONNECTOR CONNECTION)
7.CHECK FUEL PRESSURE

OK

8.CHECK FOR EXHAUST GAS LEAK

NG

REPAIR OR REPLACE FUEL SYSTEM

8.CHECK FOR EXHAUST GAS LEAK
a.

Check for exhaust gas leaks.


OK:

No gas leaks.



OK

9.CHECK FOR SPARK (SPARK TEST)

NG

REPAIR OR REPLACE EXHAUST SYSTEM

9.CHECK FOR SPARK (SPARK TEST)
a.

Perform a spark test (See page Engine / Hybrid System>2GR-FE IGNITION>IGNITION COIL AND SPARK PLUG>ON-VEHICLE INSPECTION).

HINT:
·

If the result of the spark test is normal, proceed to the next step.

·

If the spark plugs or ignition system malfunctions, engine misfire may occur. The misfire count can be read using the intelligent tester. Enter the following menus: Powertrain / Engine / Data List / All Data / Cylinder #1 Misfire Count (to Cylinder #6 Misfire Count).





NEXT

10.INSPECT FUEL INJECTOR ASSEMBLY (INJECTION AND VOLUME)
10.INSPECT FUEL INJECTOR ASSEMBLY (INJECTION AND VOLUME)
a.

Check the injection and volume.

HINT:
·

Refer to the fuel injector assembly inspection procedure (See page Engine / Hybrid System>2GR-FE FUEL>FUEL INJECTOR>INSPECTION).

·

If the fuel injector assemblies malfunction, engine misfire may occur. The misfire count can be read using the intelligent tester. Enter the following menus: Powertrain / Engine / Data List / All Data / Cylinder #1 Misfire Count (to Cylinder #6 Misfire Count).





OK

15.CHECK WHETHER DTC OUTPUT RECURS (DTC P0171, P0172, P0174 OR P0175)

NG

REPLACE FUEL INJECTOR ASSEMBLY

11.INSPECT AIR FUEL RATIO SENSOR (HEATER RESISTANCE)

OK

12.CHECK TERMINAL VOLTAGE (+B OF AIR FUEL RATIO SENSOR)

NG

12.CHECK TERMINAL VOLTAGE (+B OF AIR FUEL RATIO SENSOR)

OK

13.CHECK HARNESS AND CONNECTOR (AIR FUEL RATIO SENSOR - ECM)

NG

21.CHECK HARNESS AND CONNECTOR (AIR FUEL RATIO SENSOR - A/F RELAY)
13.CHECK HARNESS AND CONNECTOR (AIR FUEL RATIO SENSOR - ECM)

OK

14.REPLACE AIR FUEL RATIO SENSOR

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

14.REPLACE AIR FUEL RATIO SENSOR

NEXT

15.CHECK WHETHER DTC OUTPUT RECURS (DTC P0171, P0172, P0174 OR P0175)
15.CHECK WHETHER DTC OUTPUT RECURS (DTC P0171, P0172, P0174 OR P0175)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the engine switch on (IG).


c.

Turn the tester on.



e.

Turn the engine switch off and wait for at least 30 seconds.


f.

Turn the engine switch on (IG).


g.

Turn the tester on.


h.

Start the engine and warm it up.


i.

With the engine warmed up, idle the engine for 2 minutes or more.


j.

Drive the vehicle at a speed between 60 and 100 km/h (37 and 62 mph) for 5 minutes or more.


k.

Enter the following menus: Powertrain / Engine / DTC.


l.

Read the DTCs.


Result
Result Proceed to
DTC P0171, P0172, P0174 or P0175 is output A
DTC is not output B


A

16.CHECK HARNESS AND CONNECTOR (MASS AIR FLOW METER SUB-ASSEMBLY CONNECTOR CONNECTION)

B

END

16.CHECK HARNESS AND CONNECTOR (MASS AIR FLOW METER SUB-ASSEMBLY CONNECTOR CONNECTION)
a.

Check the connection and terminal contact pressure of connectors and wire harnesses between the mass air flow meter sub-assembly and ECM (See page General>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>ELECTRONIC CIRCUIT INSPECTION PROCEDURE).

HINT:

Repair any problems.




NEXT

17.CHECK WHETHER DTC OUTPUT RECURS (DTC P0171, P0172, P0174 OR P0175)
17.CHECK WHETHER DTC OUTPUT RECURS (DTC P0171, P0172, P0174 OR P0175)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the engine switch on (IG).


c.

Turn the tester on.



e.

Turn the engine switch off and wait for at least 30 seconds.


f.

Turn the engine switch on (IG).


g.

Turn the tester on.


h.

Start the engine and warm it up.


i.

With the engine warmed up, idle the engine for 2 minutes or more.


j.

Drive the vehicle at a speed between 60 and 100 km/h (37 and 62 mph) for 5 minutes or more.


k.

Enter the following menus: Powertrain / Engine / DTC.


l.

Read the DTCs.


Result
Result Proceed to
DTC P0171, P0172, P0174 or P0175 is output A
DTC is not output B


A

18.CHECK HARNESS AND CONNECTOR (MAS AIR FLOW METER SUB-ASSEMBLY - ECM)

B

END

18.CHECK HARNESS AND CONNECTOR (MAS AIR FLOW METER SUB-ASSEMBLY - ECM)

OK

19.REPLACE MASS AIR FLOW METER SUB-ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

19.REPLACE MASS AIR FLOW METER SUB-ASSEMBLY
a.

Replace the mass air flow meter sub-assembly (See page Engine / Hybrid System>2GR-FE ENGINE CONTROL>MASS AIR FLOW METER>REMOVAL).

HINT:

If the result of the inspection performed in step 6 indicated no problem, proceed to the next step without replacing the mass air flow meter sub-assembly.




NEXT

20.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
20.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
a.

Connect the intelligent tester to the DLC3.


b.

Turn the engine switch on (IG).


c.

Turn the tester on.



e.

Turn the engine switch off and wait for at least 30 seconds.


f.

Turn the engine switch on (IG).


g.

Turn the tester on.


h.

Start the engine and warm it up.


i.

With the engine warmed up, idle the engine for 2 minutes or more.


j.

Drive the vehicle at a speed between 60 and 100 km/h (37 and 62 mph) for 5 minutes or more.


k.

Enter the following menus: Powertrain / Engine / DTC.


l.

Read the DTCs.


Result
Result Proceed to
DTC is not output A
DTC P0171, P0172, P0174 or P0175 is output B


A

END

B

21.CHECK HARNESS AND CONNECTOR (AIR FUEL RATIO SENSOR - A/F RELAY)

OK

REPAIR OR REPLACE HARNESS OR CONNECTOR (EFI MAIN RELAY - A/F RELAY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR