Home › Engine / Hybrid System › 2GR-FE ENGINE CONTROL › SFI SYSTEM › from 2016.05
RM24M0E _51 Engine / Hybrid System _059540 2GR-FE ENGINE CONTROL _0291770 SFI SYSTEM C

2GR-FE ENGINE CONTROL  SFI SYSTEM  P0014  Camshaft Position "B" - Timing Over-Advanced or System Performance (Bank 1)  P0015  Camshaft Position "B" - Timing Over-Retarded (Bank 1)  P0024  Camshaft Position "B" - Timing Over-Advanced or System Performance (Bank 2)  P0025  Camshaft Position "B" - Timing Over-Retarded (Bank 2)  


DESCRIPTION

Refer to DTC P0013 (See page Engine / Hybrid System>2GR-FE ENGINE CONTROL>SFI SYSTEM>P0013).

DTC No. DTC Detection Condition Trouble Area
P0014
P0024
Advanced cam timing:
With engine warmed up and engine speed of between 500 rpm and 4000 rpm, all conditions (1), (2) and (3) are met (2 trip detection logic):
(1) Difference between target and actual exhaust valve timing is more than 5°CA (Crankshaft Angle) for 4.5 seconds
(2) Current exhaust valve timing is fixed (timing changes less than 5°CA in 5 seconds)
(3) Variations in VVT controller timing are more than 19°CA of maximum delayed timing (advanced)
·

Valve timing

·

Camshaft timing oil control valve assembly (for exhaust camshaft of bank 1, 2)

·

Oil control valve filter (RH, LH)

·

Oil pipe

·

Camshaft timing exhaust gear assembly (bank 1, 2)

·

ECM


P0015
P0025
Retarded cam timing:
With engine warmed up and engine speed of between 500 rpm and 4000 rpm, all conditions (1), (2) and (3) are met (1 trip detection logic):
(1) Difference between target and actual exhaust valve timing is more than 5°CA (Crankshaft Angle) for 4.5 seconds
(2) Current exhaust valve timing is fixed (timing changes less than 5°CA in 5 seconds)
(3) Variations in VVT controller timing are 19°CA or less of maximum delayed timing (retarded)

WIRING DIAGRAM

CAUTION / NOTICE / HINT

HINT:
Abnormal bank Advanced timing over
(Valve timing is out of specified range)
Retarded timing over
(Valve timing is out of specified range)
Bank 1 P0014 P0015
Bank 2 P0024 P0025

·

If DTC P0014 or P0015 is output, check the VVT system (for exhaust camshaft of bank 1) circuit.

·

If DTC P0024 or P0025 is output, check the VVT system (for exhaust camshaft of bank 2) circuit.

·

Bank 1 refers to the bank that includes the No. 1 cylinder*.

*: The No. 1 cylinder is the cylinder which is farthest from the transaxle.

·

Bank 2 refers to the bank that does not include the No. 1 cylinder.

·

DTC P0014, P0015, P0024 or P0025 may be stored when foreign objects in the engine oil are caught in some parts of the system. The DTC will remain stored even if the system returns to normal after a short time. Those foreign objects may then be captured by the oil filter.

·

Read freeze frame data using the intelligent tester. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can be helpful in determining whether the vehicle was running or stopped, whether the engine was warmed up or not, whether the air-fuel ratio was lean or rich, as well as other data recorded at the time of a malfunction.



PROCEDURE

1.CHECK ANY OTHER DTCS OUTPUT (IN ADDITION TO DTC P0014, P0015, P0024 OR P0025)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the engine switch on (IG) and turn the tester on.


c.

Enter the following menus: Powertrain / Engine / DTC.


d.

Read the DTCs.

Result
Result Proceed to
DTC P0014, P0015, P0024 or P0025 is output A
DTC P0014, P0015, P0024 or P0025 and other DTCs are output B

HINT:

If any DTCs other than P0014, P0015, P0024 or P0025 are output, troubleshoot those DTCs first.




A

2.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (CONTROL THE VVT EXHAUST LINEAR)

B

2.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (CONTROL THE VVT EXHAUST LINEAR)
a.

Connect the intelligent tester to the DLC3.


b.

Start the engine.


c.

Turn the tester on.


d.

Turn the A/C switch on.


e.

Enter the following menus: Powertrain / Engine / Active Test / Control the VVT Exhaust Linear (Bank 1) or Control the VVT Exhaust Linear (Bank 2).


f.

Check the engine speed while operating the camshaft timing oil control valve assembly (for exhaust camshaft) using the tester.

OK
Tester Operation Engine Condition
0% Normal engine speed
100% Engine idles roughly or stalls

HINT:

Refer to "Data List / Active Test" [VVT Ex OCV Duty #1, VVT Ex Chg Angle #1, VVT Ex OCV Duty #2 and VVT Ex Chg Angle #2] (See page Engine / Hybrid System>2GR-FE ENGINE CONTROL>SFI SYSTEM>DATA LIST / ACTIVE TEST).




OK

3.CHECK WHETHER DTC OUTPUT RECURS (DTC P0014, P0015, P0024 OR P0025)

NG

4.CHECK VALVE TIMING (CHECK FOR LOOSE AND JUMPED TEETH ON TIMING CHAIN)
3.CHECK WHETHER DTC OUTPUT RECURS (DTC P0014, P0015, P0024 OR P0025)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the engine switch on (IG) and turn the tester on.


c.

Clear the DTCs.


d.

Start the engine and warm it up.


e.

Drive the vehicle for more than 10 minutes.


f.

Enter the following menus: Powertrain / Engine / DTC / Pending.


g.

Read the pending DTCs.

Result
Result Proceed to
DTC is not output A
DTC P0014, P0015, P0024 or P0025 is output B

HINT:

DTC P0014, P0015, P0024 or P0025 may be stored when foreign objects in the engine oil are caught in some parts of the system. The DTC will remain stored even if the system returns to normal after a short time. Those foreign objects may then be captured by the oil filter.




A

B

4.CHECK VALVE TIMING (CHECK FOR LOOSE AND JUMPED TEETH ON TIMING CHAIN)
4.CHECK VALVE TIMING (CHECK FOR LOOSE AND JUMPED TEETH ON TIMING CHAIN)

OK

5.INSPECT CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY (FOR EXHAUST CAMSHAFT)

NG

5.INSPECT CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY (FOR EXHAUST CAMSHAFT)
a.

Inspect the camshaft timing oil control valve assembly (for exhaust camshaft) (See page Engine / Hybrid System>2GR-FE ENGINE CONTROL>CAMSHAFT OIL CONTROL VALVE>INSPECTION).



OK

6.INSPECT OIL CONTROL VALVE FILTER AND OIL PIPE

NG

REPLACE CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY (FOR EXHAUST CAMSHAFT)

6.INSPECT OIL CONTROL VALVE FILTER AND OIL PIPE

OK

7.REPLACE CAMSHAFT TIMING EXHAUST GEAR ASSEMBLY

NG

REPLACE OIL CONTROL VALVE FILTER OR OIL PIPE

7.REPLACE CAMSHAFT TIMING EXHAUST GEAR ASSEMBLY
a.

Replace the camshaft timing exhaust gear assembly (bank 1 or bank 2) (See page Engine / Hybrid System>2GR-FE ENGINE MECHANICAL>ENGINE UNIT>DISASSEMBLY).



NEXT

8.CHECK WHETHER DTC OUTPUT RECURS (DTC P0014, P0015, P0024 OR P0025)
8.CHECK WHETHER DTC OUTPUT RECURS (DTC P0014, P0015, P0024 OR P0025)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the engine switch on (IG) and turn the tester on.


c.

Clear the DTCs.


d.

Turn the engine switch off and wait for at least 30 seconds.


e.

Start the engine and warm it up.


f.

Drive the vehicle for more than 10 minutes.


g.

Enter the following menus: Powertrain / Engine / DTC / Pending.


h.

Read the pending DTCs.

Result
Result Proceed to
DTC is not output A
DTC P0014, P0015, P0024 or P0025 is output B



A

END

B