13507
1.INSTALL NO. 2 CHAIN SUB-ASSEMBLY
Set the crankshaft key in the left horizontal position.
Turn the cutout of the drive shaft so that it faces upward.
Align the yellow mark links with the timing marks of each gear as shown in the illustration.
Install the sprockets onto the crankshaft and oil pump shaft with the chain wrapped on the gears.
Temporarily tighten the oil pump drive shaft sprocket with the nut.
Insert the damper spring into the adjusting hole, and then install the chain tensioner plate with the bolt.
Align the adjusting hole of the oil pump drive shaft sprocket with the groove of the oil pump.
Insert a 4 mm diameter bar into the adjusting hole of the oil pump drive shaft gear to lock the gear in position, and then tighten the nut.
13521
2.INSTALL CRANKSHAFT TIMING SPROCKET
13561
3.INSTALL NO. 1 CHAIN VIBRATION DAMPER
Install the chain vibration damper with the 2 bolts.
13506
4.INSTALL CHAIN SUB-ASSEMBLY
Set the No. 1 cylinder to TDC/compression.
Turn the camshafts with a wrench (using the hexagonal lobe) to align the timing marks of the camshaft timing gear with each timing mark located on the No. 1 and No. 2 bearing caps as shown in the illustration.
Using the crankshaft pulley bolt, turn the crankshaft to position the key on the crankshaft upward.
Install the chain onto the crankshaft timing sprocket with the gold or orange mark link aligned with the timing mark on the crankshaft.
Using SST and a hammer, tap in the crankshaft timing sprocket.
Align the gold or yellow links with each timing mark located on the camshaft timing gear and sprocket, then install the chain.
13559
5.INSTALL CHAIN TENSIONER SLIPPER
Install the chain tensioner slipper with the bolt.
13566B
6.INSTALL TIMING CHAIN GUIDE
Install the timing chain guide with the bolt.
19315
7.INSTALL NO. 1 CRANKSHAFT POSITION SENSOR PLATE
Install the sensor plate with the "F" mark facing forward.
11302
8.INSTALL TIMING CHAIN COVER SUB-ASSEMBLY
Remove any old packing material and be careful not to drop any oil on the contact surfaces of the timing chain cover, cylinder head and cylinder block.
Apply seal packing as shown in the illustration.
Toyota Genuine Seal Packing Black, Three Bond 1207B or equivalent
4.0 to 4.5 mm (0.157 to 0.177 in.)
| *1 | Seal Packing |
Remove any oil from the contact surfaces.
Install the chain cover within 3 minutes of applying seal packing.
Do not add engine oil for at least 2 hours after installing the chain cover.
Apply a continuous bead of seal packing as shown in the illustration.
Toyota Genuine Seal Packing Black, Three Bond 1207B or equivalent
| Area | Seal Packing Diameter (Round) | Distance from Edge of Cover to Edge of Seal Packing | Diameter Measured from Center of Seal Packing |
|---|---|---|---|
| A | 4.0 mm (0.157 in.) | - | - |
| B | 5.5 to 6.0 mm (0.217 to 0.236 in.) | - | - |
| C | 3.0 mm (0.118 in.) | - | - |
| D | 2.5 to 3.0 mm (0.0984 to 0.118 in.) | 2.5 mm (0.0984 in.) | - |
| E | 4.0 to 4.5 mm (0.157 to 0.177 in.) | - | - |
| F | 4.5 to 5.0 mm (0.177 to 0.197 in.) | - | - |
| G | 2.5 to 3.0 mm (0.0984 to 0.118 in.) | - | - |
| H | 4.0 mm (0.157 in.) | - | 17.5 mm (0.689 in.) |
| I | 2.5 to 3.0 mm (0.0984 to 0.118 in.) | - | 13.0 mm (0.512 in.) |
Remove any oil from the contact surfaces.
Install the chain cover within 3 minutes of applying seal packing.
Do not add engine oil for at least 2 hours after installing the chain cover.
Apply adhesive to the threads of bolt A.
Toyota Genuine Adhesive 1324, Three Bond 1324 or equivalent
Temporarily install the timing chain cover with the 12 bolts and 2 nuts.
| Item | Specified Condition |
|---|---|
| Bolt A | 30 mm (1.18 in.)
10 mm head |
| Bolt B | 30 mm (1.18 in.)
12 mm head |
| Bolt C | 40 mm (1.57 in.)
14 mm head |
| *1 | Nut |
Temporarily install the engine mounting bracket with the 3 bolts.
Tighten the 15 bolts and 2 nuts in the sequence shown in the illustration.
Using an E10 "TORX" socket, install the stud bolt for the V-ribbed belt tensioner.
13540
9.INSTALL NO. 1 CHAIN TENSIONER ASSEMBLY
Release the ratchet pawl, then fully push in the plunger and hook the hook to the pin so that the plunger is in the position shown in the illustration.
Install a new gasket and the chain tensioner with the 2 nuts.
When installing the chain tensioner, set the hook again if the hook releases the plunger.
16620
10.INSTALL V-RIBBED BELT TENSIONER ASSEMBLY
Temporarily install the V-ribbed belt tensioner assembly with the nut.
Do not lift the engine more than necessary.
Slightly push down on the V-ribbed belt tensioner assembly at the part (A) to align the holes of the engine and tensioner as shown in the illustration, and temporarily install the bolt.
Tighten the bolt and nut to install the V-ribbed belt tensioner.
When replacing the V-ribbed belt tensioner with a new one, do not pull out the pin.
The pin will be removed in a later step.
16603B
11.INSTALL IDLER PULLEY BRACKET
Install the idler pulley bracket with the 2 bolts.
12305
12.INSTALL ENGINE MOUNTING INSULATOR RH
12361A
13.INSTALL FRONT ENGINE MOUNTING INSULATOR
12281A
14.REMOVE ENGINE HANGER
Remove the chain block and sling device.
Remove the No. 1 and No. 2 engine hangers.
13471
15.INSTALL CRANKSHAFT PULLEY
Using SST, secure the pulley in place and tighten the bolt.
T = 180 N*m{ 1,835 kgf*cm 133 ft.*lbf }
Turn the crankshaft counterclockwise, then disconnect the plunger knock pin from the hook.
Turn the crankshaft clockwise, then check that the plunger is extended.
12101
16.INSTALL OIL PAN SUB-ASSEMBLY
Remove any old packing material and be careful not to drop any oil on the contact surfaces of the cylinder block and oil pan.
Apply a continuous bead of seal packing (Diameter: 3.0 to 4.0 mm (0.118 to 0.157 in.)) as shown in the illustration.
Toyota Genuine Seal Packing Black, Three Bond 1207B or Equivalent
Remove any oil from the contact surfaces.
Install the oil pan within 3 minutes of applying seal packing.
Do not add engine oil for at least 2 hours after installing the oil pan.
Install the oil pan to the cylinder block.
Uniformly tighten the 12 bolts and 2 nuts in the sequence shown in the illustration.
11301K
17.INSTALL CRANKSHAFT POSITION SENSOR
Apply a light coat of engine oil to the O-ring on the crank position sensor.
| *1 | O-ring |
Install the crank position sensor with the bolt.
Do not twist the O-ring.
Install the 2 wire harness clamps.
Install the connector to the connector bracket.
11201
18.INSTALL CYLINDER HEAD COVER SUB-ASSEMBLY
Remove any old packing material from the contact surface.
Apply seal packing to the 2 locations shown in the illustration.
Toyota Genuine Seal Packing Black, Three Bond 1207B or Equivalent
Remove any oil from the contact surfaces.
Install the oil pan within 3 minutes of applying seal packing.
Do not add engine oil for at least 2 hours after installing the oil pan.
Install the cylinder head cover with the 8 bolts and 2 nuts.
Install the 2 engine wires with the 2 bolts.
Connect the 2 ventilation hoses to the cylinder head cover.
19500
19.INSTALL IGNITION COIL ASSEMBLY
16611
20.INSTALL RADIATOR RESERVOIR BRACKET
16470
21.INSTALL RADIATOR RESERVOIR ASSEMBLY
27020
22.INSTALL GENERATOR ASSEMBLY
16361A
23.INSTALL FAN AND GENERATOR V BELT
51217A
24.INSTALL FRONT SUSPENSION MEMBER REINFORCEMENT RH
17410
25.INSTALL FRONT EXHAUST PIPE
26.INSTALL COWL TOP OUTER PANEL WITH WINDSHIELD WIPER MOTOR AND LINK
Install the cowl top outer panel with windshield wiper motor and link (See page Vehicle Interior>WIPER / WASHER>FRONT WIPER MOTOR>INSTALLATION).
27.ADD ENGINE OIL
28.CONNECT CABLE TO NEGATIVE BATTERY TERMINAL
29.CHECK FOR ENGINE OIL LEAKS
30.CHECK FOR EXHAUST GAS LEAKS
53701
31.INSTALL FRONT FENDER APRON RH
51441
32.INSTALL NO. 1 ENGINE UNDER COVER
33.INSTALL FRONT WHEEL RH
53292A
34.INSTALL UPPER RADIATOR SUPPORT SEAL
35.PERFORM INITIALIZATION
Perform initialization (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).
Certain systems need to be initialized after disconnecting and reconnecting the cable from the negative (-) battery terminal.