Home › Drivetrain › K112 (CVT) › TRANSMISSION CONTROL CABLE(for RHD) › from 2016.05
RM24M0E _52 Drivetrain _059572 K112 CVT _0292060 TRANSMISSION CONTROL CABLE(for RHD) A

K112 CVT  TRANSMISSION CONTROL CABLE(for RHD)  REMOVAL  


PROCEDURE

Hide 53292A 1.REMOVE UPPER RADIATOR SUPPORT SEAL

Hide 2.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

NOTICE:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to prevent airbag and seat belt pretensioner activation (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).


Hide 55712 5.REMOVE FRONT COWL TOP OUTSIDE PANEL WITH WINDSHIELD WIPER MOTOR AND LINK

Hide 17705 7.REMOVE AIR CLEANER CAP SUB-ASSEMBLY

Hide 17700 8.REMOVE AIR CLEANER CASE SUB-ASSEMBLY

Hide 17751 9.REMOVE NO. 1 AIR CLEANER INLET

Hide 17752 10.REMOVE NO. 2 AIR CLEANER INLET

Hide 33554H 13.REMOVE SHIFT LOCK RELEASE BUTTON COVER

Hide 33504F 14.REMOVE SHIFT LEVER KNOB SUB-ASSEMBLY

Hide 15.REMOVE CENTER INSTRUMENT CLUSTER FINISH PANEL ASSEMBLY

Hide 55041B 16.REMOVE NO. 1 INSTRUMENT PANEL BOX DOOR SUB-ASSEMBLY

Hide 55042B 17.REMOVE NO. 2 INSTRUMENT PANEL BOX DOOR SUB-ASSEMBLY

Hide 55550 18.REMOVE GLOVE COMPARTMENT DOOR ASSEMBLY

Hide 55607 19.REMOVE NO. 2 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY

Hide 67913B 20.REMOVE FRONT DOOR SCUFF PLATE RH

Hide 62111C 21.REMOVE COWL SIDE TRIM BOARD RH

Hide 55606 22.REMOVE NO. 1 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY

Hide 55432B 23.REMOVE INSTRUMENT PANEL FINISH PANEL LOWER (w/o Knee Airbag)

Hide 55432B 24.REMOVE INSTRUMENT PANEL FINISH PANEL LOWER (w/ Knee Airbag)

Hide 58534E 25.REMOVE FLOOR CARPET COVER CENTER LH

Hide 58533C 26.REMOVE FLOOR CARPET COVER CENTER RH

Hide 55434B 27.REMOVE INSTRUMENT PANEL FINISH PANEL LOWER CENTER

Hide 55475B 28.REMOVE CENTER INSTRUMENT CLUSTER FINISH PANEL GARNISH

Hide 29.REMOVE TRANSMISSION CONTROL CABLE ASSEMBLY

a.

Move the shift lever to N.


b.
C133003

Disconnect the end of the transmission control cable from the shift lever assembly.


c.
C264709E01
0.639,0.538 0.857,0.707 0.218,0.170 10 *1 1.514,0.881 0.828,0.624 false

Using a screwdriver, pull out the stopper of the transmission control cable.

Text in Illustration
*1 Stopper

NOTICE:

Do not remove the stopper. If the stopper is removed, reinstall it to its original position.



d.
C264710E01
0.168,2.468 0.366,2.646 0.199,0.178 10 *1 1.199,1.523 0.63,2.558 0.63,2.558 0.393,2.558 false

Rotate the nut of the transmission control cable counterclockwise approximately 180° and, while holding the nut in that position, disconnect the transmission control cable from the shift lever retainer.

Text in Illustration
*1 Nut

NOTICE:

Do not over-rotate the nut as it will come off the internal spring and the transmission control cable will not be reusable.



e.
C189456

Remove the nut and disconnect the control cable assembly from the control shaft lever.


f.

Remove the clip and disconnect the transmission control cable assembly from the control cable bracket.


g.

Disconnect the control cable assembly from the control cable bracket.


h.
C137660

Remove the 2 nuts and disconnect the transmission control cable clamp from the body.


i.
C367548

Remove the 2 bolts and disconnect the transmission control cable.


j.

Pull out the transmission control cable.