Home › Engine / Hybrid System › 2AZ-FE ENGINE MECHANICAL › ENGINE ASSEMBLY › from 2016.05
RM24M0E _51 Engine / Hybrid System _059548 2AZ-FE ENGINE MECHANICAL _0291835 ENGINE ASSEMBLY A

2AZ-FE ENGINE MECHANICAL  ENGINE ASSEMBLY  REMOVAL  


PROCEDURE

Hide 28800J 2.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).


Hide 3.REMOVE FRONT WHEEL

Hide 51441 4.REMOVE NO. 1 ENGINE UNDER COVER

Hide 51442 5.REMOVE NO. 2 ENGINE UNDER COVER

Hide 53702 6.REMOVE FRONT FENDER APRON LH

Hide 53701 7.REMOVE FRONT FENDER APRON RH

Hide 53301 9.REMOVE HOOD SUB-ASSEMBLY

a.

Remove the 4 bolts and hood sub-assembly.


Hide 53292A 10.REMOVE UPPER RADIATOR SUPPORT SEAL

Hide 12.DRAIN AUTOMATIC TRANSAXLE FLUID (for Automatic Transaxle)

Hide 13.DRAIN CONTINUOUSLY VARIABLE TRANSAXLE FLUID (for CVT)

Hide 51218A 14.REMOVE FRONT SUSPENSION MEMBER REINFORCEMENT LH

a.

Remove the 4 bolts and front suspension member reinforcement LH.


Hide 51217A 15.REMOVE FRONT SUSPENSION MEMBER REINFORCEMENT RH

a.

Remove the 4 bolts and front suspension member reinforcement RH.

A132609


Hide 17410 16.REMOVE FRONT EXHAUST PIPE ASSEMBLY

Hide 16571C 17.DISCONNECT NO. 1 RADIATOR HOSE

a.

Disconnect the No. 1 radiator hose.


Hide 16572D 18.DISCONNECT NO. 2 RADIATOR HOSE

a.

Disconnect the No. 2 radiator hose.


Hide 16283H 19.DISCONNECT NO. 6 WATER BY-PASS HOSE (for CVT)

a.
A284862

w/ Air Cooled Transmission Oil Cooler:

i.

Disconnect the No. 6 water by-pass hose from the No. 4 water by-pass pipe.



Hide 32942C 20.DISCONNECT OUTLET NO. 1 OIL COOLER HOSE (for CVT)

a.
A283488

w/ Air Cooled Transmission Oil Cooler:

i.

Disconnect the outlet No. 1 oil cooler hose from the oil cooler outlet tube.



Hide 32941D 21.DISCONNECT INLET OIL COOLER HOSE (for CVT)

a.
A284769

w/ Air Cooled Transmission Oil Cooler:

i.

Disconnect the inlet oil cooler hose from the oil cooler outlet tube.



Hide 22.DISCONNECT OIL COOLER HOSE (for Automatic Transaxle)

a.
C202162

Disconnect the 2 oil cooler hoses from the automatic transaxle assembly.


Hide 23.REMOVE COWL TOP OUTER PANEL WITH WINDSHIELD WIPER MOTOR AND LINK

Hide 74431 25.REMOVE BATTERY TRAY

Hide 17705 26.REMOVE AIR CLEANER CAP SUB-ASSEMBLY

Hide 17700 27.REMOVE AIR CLEANER CASE SUB-ASSEMBLY

Hide 17752 28.REMOVE NO. 2 AIR CLEANER INLET

Hide 74411 29.REMOVE BATTERY CARRIER

a.
A132516

Disconnect the wire harness clamp.


b.

Remove the 4 bolts and battery carrier.


Hide 74414D 30.REMOVE BATTERY CARRIER SUPPORT

a.
A132517

Remove the 2 bolts and battery carrier support.


Hide 77251B 31.DISCONNECT FUEL MAIN TUBE

Hide 35104V 32.DISCONNECT BREATHER PLUG HOSE

a.
A287317E01
0.067,0.002 0.293,0.186 0.225,0.184 10 *A 0.076,2.263 0.301,2.446 0.225,0.184 10 *B

Disconnect the breather plug hose from the clamp.

Text in Illustration
*A for Automatic Transaxle
for CVT (w/ Air Cooled Transmission Oil Cooler)
*B for CVT (w/o Air Cooled Transmission Oil Cooler)


Hide 87245A 33.DISCONNECT HEATER WATER INLET HOSE

a.

Disconnect the water by-pass hoses (for Automatic Transaxle or CVT (w/ Air Cooled Transmission Oil Cooler)).

A394014E01
0.229,0.156 0.542,0.354 0.313,0.198 10 false *A 4.042,0.167 4.354,0.365 0.313,0.198 10 false *B


b.

Disconnect the water by-pass hoses (for CVT (w/o Air Cooled Transmission Oil Cooler)).

Text in Illustration
*A for Automatic Transaxle
for CVT (w/ Air Cooled Transmission Oil Cooler)
*B for CVT (w/o Air Cooled Transmission Oil Cooler)


Hide 87246B 34.DISCONNECT HEATER WATER OUTLET HOSE

a.

Disconnect the heater water outlet hose.


Hide 25860 35.DISCONNECT PURGE LINE HOSE

a.
A234690

Disconnect the purge line hose.


Hide 44774 36.DISCONNECT UNION TO CONNECTOR TUBE HOSE

a.

Disconnect the 2 union to connector tube hoses from the booster vacuum tube.


Hide 16470 38.REMOVE RADIATOR RESERVOIR ASSEMBLY

a.
A132520

Disconnect the No. 1 and No. 2 water by-pass hoses.


b.

Remove the bolt and radiator reservoir assembly.


Hide 16611 39.REMOVE RADIATOR RESERVOIR BRACKET

a.
A132521

Remove the 2 bolts and radiator reservoir bracket.


Hide 16361A 40.REMOVE FAN AND GENERATOR V BELT

Hide 82121 43.DISCONNECT ENGINE WIRE

a.

Remove the engine room relay block cover.


b.
A132522

Disconnect the 2 connectors.


c.
A132523

Pull up the relay block side cover.


d.

Remove the nut and battery positive (+) cable.


e.
A132525

Remove the 2 bolts and battery ground cable.


f.
A132524

Remove the 2 bolts, engine wire harness cover and ground cable.


g.

Disconnect the crankshaft position sensor connector.


h.
A132526

Remove the bolt and ground cable.


i.

Remove the bolt and engine wire harness clamp.


Hide 88320 44.REMOVE COOLER COMPRESSOR ASSEMBLY

a.

Remove the cooler compressor assembly (See page Vehicle Interior>AIR CONDITIONING>COMPRESSOR(for 2AZ-FE)>REMOVAL).

HINT:

Disconnect the compressor together with the low-pressure and high-pressure hoses, then secure it to the vehicle side using rope.



Hide 45.DISCONNECT TRANSAXLE CONTROL CABLE ASSEMBLY (for Automatic Transaxle)

Hide 45259A 47.REMOVE COLUMN HOLE COVER SILENCER SHEET

a.
A132529

Fold back the floor carpet, remove the 2 clips and remove the column hole cover silencer sheet.


Hide 45221 48.SEPARATE STEERING INTERMEDIATE SHAFT

a.

Place matchmarks on the steering intermediate shaft and steering gear.


b.
A132530E02
1.542,2.313 2.219,2.313 false 2.302,2.219 3.063,2.573 0.76,0.354 10 true Matchmark

Remove the bolt and separate the steering intermediate shaft.


Hide 45025D 49.DISCONNECT NO. 1 STEERING COLUMN HOLE COVER SUB-ASSEMBLY

a.
U189025E01
0.257,0.365 0.410,0.577 0.153,0.211 10 A 2.457,1.647 2.610,1.858 0.153,0.211 10 B

Push clip A in the direction of the cover's center, and push down clip B to separate the No. 1 steering column hole cover sub-assembly from the floor panel.


Hide 43410 50.REMOVE FRONT DRIVE SHAFT

Hide 12361A 51.REMOVE FRONT ENGINE MOUNTING INSULATOR

a.
A124839E03
2.24,0.958 3.063,1.333 0.823,0.375 10 true Through Bolt 1.042,1.74 1.292,1.917 0.25,0.177 10 false Nut

Remove the through bolt and nut.


b.
A124840

Remove the 2 bolts and front engine mounting insulator.


Hide 12371A 52.REMOVE REAR ENGINE MOUNTING INSULATOR

a.
A132533

Remove the through bolt.


b.
A124842

Remove the 2 nuts, 2 bolts and rear engine mounting insulator.


Hide 57104E 53.REMOVE FRONT CROSSMEMBER SUB-ASSEMBLY

a.

Remove the 4 bolts and front crossmember sub-assembly.

A132563


Hide 51403B 54.REMOVE FRONT SUSPENSION MEMBER BRACE SUB-ASSEMBLY

a.

Remove the 6 bolts and front suspension member brace sub-assembly LH and front suspension member brace sub-assembly RH.

A132564


Hide 51201 55.REMOVE FRONT SUSPENSION CROSSMEMBER SUB-ASSEMBLY

a.

Remove the 2 bolts and front suspension crossmember sub-assembly.

A132565


Hide 12305 57.REMOVE ENGINE MOUNTING INSULATOR RH

a.
A132539

Remove the 2 nuts, 2 bolts and engine mounting insulator RH.


Hide 12372A 58.REMOVE ENGINE MOUNTING INSULATOR LH

a.
A124844E02
0.646,1.563 0.906,1.74 0.26,0.177 10 false Nut 2.24,1.698 3.26,2.094 1.021,0.396 10 true Through Bolt

Remove the through bolt and nut.


b.
A124845

Remove the 4 bolts and engine mounting insulator LH.


Hide 11000 59.REMOVE ENGINE ASSEMBLY

a.

Set an engine lifter underneath the engine assembly.

HINT:

Set wooden blocks or equivalent under the engine assembly, so that the engine is level.



b.

Remove the sling device and chain block from the engine hangers.


c.

Carefully remove the engine assembly from the vehicle.

NOTICE:
·

Make sure that the engine is clear of all wiring and hoses.

·

While lowering the engine assembly from the vehicle, do not allow it to contact the vehicle.




d.

Remove the 2 engine hangers.


Hide 12262 60.DISCONNECT NO. 2 VENTILATION HOSE

Hide 23807 61.REMOVE FUEL DELIVERY PIPE SUB-ASSEMBLY

Hide 23250 62.REMOVE FUEL INJECTOR ASSEMBLY

Hide 17135A 64.REMOVE NO. 1 INTAKE MANIFOLD INSULATOR

Hide 82121 65.DISCONNECT ENGINE WIRE

a.
U188339E02
0.208,1.656 0.365,1.823 0.156,0.167 10 false A 1.979,1.865 2.135,2.031 0.156,0.167 10 false B 2.677,1.802 2.833,1.969 0.156,0.167 10 false B 3.125,0.469 3.281,0.635 0.156,0.167 10 false B

Remove the 4 bolts (A) and (B) shown in the illustration.


b.

Disconnect the knock sensor connector.


c.
U188336E02
0.302,0.146 0.448,0.333 0.146,0.188 10 false A 0.208,1.479 0.354,1.667 0.146,0.188 10 false B 0.823,1.844 0.969,2.031 0.146,0.188 10 false C 1.063,0.833 1.208,1.021 0.146,0.188 10 false D 2.76,0.417 2.906,0.604 0.146,0.188 10 false E 1.458,0.281 1.604,0.469 0.146,0.188 10 false F

Disconnect the radio setting condenser connector (A), oil pressure sensor connector (B), engine coolant temperature sensor connector (C), heated oxygen sensor connector (D) and camshaft position sensor connector (E) shown in the illustration.


d.

Remove the bolt and ground cable (F) shown in the illustration.


e.

Disconnect the 4 ignition coil connectors.


f.
A132644

Disconnect the camshaft timing oil control valve connector.


g.
A132624

Remove the 2 bolts and engine wire harness cover.


Hide 43457 66.REMOVE DRIVE SHAFT BEARING BRACKET

a.
A098759

Remove the 3 bolts and drive shaft bearing bracket.


Hide 16282D 67.DISCONNECT NO. 5 WATER BY-PASS HOSE (for CVT)

a.
A193345

Disconnect the No. 5 water by-pass hose.


Hide 30500 68.REMOVE AUTOMATIC TRANSAXLE ASSEMBLY (for Automatic Transaxle)

Hide 30400 69.REMOVE CONTINUOUSLY VARIABLE TRANSAXLE ASSEMBLY (for CVT)

Hide 32101 70.REMOVE DRIVE PLATE AND RING GEAR SUB-ASSEMBLY

a.
A126932E01
1.087,1.621 1.444,1.797 0.357,0.177 10 SST 1.442,1.124 1.267,1.59 1.267,1.59 1.839,1.317 false

Using SST, hold the crankshaft pulley.

SST
09213-54015  (91651-60855)
09330-00021  


b.
A112224

Remove the 8 bolts, rear spacer, drive plate and ring gear sub-assembly and front spacer.