ENGINE START SYSTEM FUNCTION
If the engine switch is pressed with the shift lever in the P or N position and the brake pedal depressed, the main body ECU determines that it is an engine start request.
The certification ECU and other ECUs perform key verification via the LIN communication line.
The main body ECU activates the ACC relay.
The main body ECU activates the LH-IG Relay 1, LH-IG relay 2, RH-IG Relay 1 and IG2 relays.
The certification ECU outputs a steering UNLOCK signal. The signal is sent to the main body ECU via the steering lock ECU.
The main body ECU sends an engine start request signal to the ECM.
The ECM sends an ACC cut request signal to the main body ECU.
The ECM and main body ECU activate the ST relay.
The main body ECU deactivates the ACC relay until the ECU detects an engine start.
When engine revolution speed reaches 1200 rpm, the ECM determines that the engine has been started.
The ECM stops sending on ACC cut request signal to the main body ECU.
The main body ECU reactivates the ACC relay and turns off the engine switch indicator light, when engine revolution speed reaches 800 rpm.
| Symbols of main body ECU | Signals | |
|---|---|---|
| STP | Stop light switch ON signal | Input |
| SSW1/SSW2 | Engine switch ON signal | Input |
| ACCD | ACC relay operation signal | Output |
| SLP | Steering lock actuator position signal | Input |
| IG1D | LH-IG Relay 1, LH-IG Relay 2 and RH IG Relay 1 operation signal | Output |
| IG2D | IG2 relay operation signal | Output |
| STR2 | ST relay operation signal (Sub) | Output |
| STR | Park/Neutral start switch signal | Input |
| TACH | Engine start detection signal | Input |
| STSW | Starter activation request signal | Output |
| ACCR | ACC cut request signal | Input |
| Symbols of ECM | Signals | |
|---|---|---|
| ACCR | ACC cut request signal | Output |
| TACH | Engine revolution speed signal | Output |
| STSW | Starter activation request signal | Input |
| STAR | ST relay operation signal (Main) | Output |
| STA | Starter activation signal | Input |
See CRANKING HOLDING FUNCTION CIRCUIT (See page Engine / Hybrid System>2GR-FE ENGINE CONTROL>SFI SYSTEM>Cranking Holding Function Circuit).
EMERGENCY ENGINE START CONTROL
If there is a malfunction in the stop light switch or STOP fuse, their signals may not be correctly transmitted to the main body ECU. This may result in the engine not starting even if the engine switch is pressed while the brake pedal is depressed and the shift lever is in the P or N position.
To activate the starter:
Turn the engine switch from off to on (ACC).
Press and hold the engine switch for 15 seconds.
After the main body ECU, certification ECU, steering lock ECU, ID code box and/or ECM are/is replaced, perform the registration procedures for the engine immobiliser system.
Inspect entry detection area.
When the electrical key is in either of the 2 inspection points in the illustration, the shift lever is in the P or N position and the brake pedal is depressed, check that the engine switch indicator illuminates in green.
Engine switch illuminates in green.
If the engine switch does not illuminate, perform troubleshooting according to the PROBLEM SYMPTOMS TABLE of the smart entry and start system (starting) (engine switch indicator light does not come on) (See page Engine / Hybrid System>2GR-FE STARTING>SMART ENTRY AND START SYSTEM>Engine Switch Indicator Circuit) and the smart entry and start system (entry door lock) (room oscillator does not recognize key) (See page Vehicle Interior>DOOR LOCK>SMART ENTRY AND START SYSTEM>Room Oscillator does not Recognize Key).
OK
NG
Turn the engine switch off.
Make sure that the shift lever is in the P or N position.
Open and close the driver's door.
When the shift lever is in the P or N position and the brake pedal is depressed, check if the engine can be started.
Steering lock/unlock function operates normally and engine can be started.
After the battery is discharged and then recharged, the engine may not start unless the steering lock is initialized using the above procedure (See page Steering>STEERING COLUMN>STEERING LOCK SYSTEM>PROBLEM SYMPTOMS TABLE).
OK
NG
Delete the DTCs (See page Engine / Hybrid System>2GR-FE STARTING>SMART ENTRY AND START SYSTEM>DTC CHECK / CLEAR).
Check for DTCs again.
No DTC is output.
If smart entry and start system (starting function) DTCs are output (See page Engine / Hybrid System>2GR-FE STARTING>SMART ENTRY AND START SYSTEM>DIAGNOSTIC TROUBLE CODE CHART).
If electrical steering lock DTCs are output (See page Steering>STEERING COLUMN>STEERING LOCK SYSTEM>DIAGNOSTIC TROUBLE CODE CHART).
If engine immobiliser system DTCs are output (See page Vehicle Interior>ENGINE IMMOBILISER>ENGINE IMMOBILISER SYSTEM>DIAGNOSTIC TROUBLE CODE CHART).
If engine control system DTCs output (2GR-FE) (See page Engine / Hybrid System>2GR-FE ENGINE CONTROL>SFI SYSTEM>DIAGNOSTIC TROUBLE CODE CHART).
OK
NG
Check the power source mode changes.
When the key is inside the vehicle and the shift lever is in the P or N position, check that pressing the engine switch causes the power source mode to change as follows:
off → on (ACC) → on (IG) → off
If power source mode does not change to ON (IG and ACC) (See page Engine / Hybrid System>2GR-FE STARTING>SMART ENTRY AND START SYSTEM>Power Source Mode does not Change to ON (IG and ACC)).
If power source mode does not change to ON (IG) (See page Engine / Hybrid System>2GR-FE STARTING>SMART ENTRY AND START SYSTEM>Power Source Mode does not Change to ON (IG)).
If power source mode does not change to ON (ACC) (See page Engine / Hybrid System>2GR-FE STARTING>SMART ENTRY AND START SYSTEM>Power Source Mode does not Change to ON (ACC)).
OK
NG
Check the engine cranking function.
When there is fuel in the fuel tank, the key is inside the vehicle, and the shift lever is in the P or N position, check that depressing the brake pedal and pressing the engine switch crank the engine.
| Result | Proceed to |
|---|---|
| Engine does not crank | A |
| Engine cranks | B |
A
B
Connect the intelligent tester to the DLC3.
Turn the engine switch on (IG)
Read the DATA LIST according to the displays on the tester screen.
| Tester Display | Measurement Item/Range | Normal Condition | Diagnostic Note |
|---|---|---|---|
| Shift P Sig | Shift P signal / ON or OFF | ON: Shift position is P
OFF: Shift position is not P |
- |
ON (P signal is ON) and OFF (P signal is OFF) appear on the screen.
If the result is not as specified, perform troubleshooting for DTC B2281 ("P" signal malfunction) first (See page Engine / Hybrid System>2GR-FE STARTING>SMART ENTRY AND START SYSTEM>B2281).
OK
NG
Connect the intelligent tester to the DLC3.
Turn the engine switch on (IG).
Read the DATA LIST according to the displays on the tester screen.
| Tester Display | Measurement Item/Range | Normal Condition | Diagnostic Note |
|---|---|---|---|
| Stop Light SW | Stop Light Switch / ON or OFF | ON: Brake pedal depressed
OFF: Brake pedal released |
- |
ON (brake pedal depressed) and OFF (brake pedal released) appear on the screen.
If the result is not as specified, perform troubleshooting for DTC B2284 (Brake signal malfunction) first.
OK
NG
Connect the intelligent tester to the DLC3.
Turn the engine switch on (IG).
| Tester Display | Measurement Item/Range | Normal Condition | Diagnostic Note |
|---|---|---|---|
| Str Unlock SW | Steering lock condition / ON or OFF | ON: Steering is unlocked (Engine switch on (ACC))
OFF: Steering is locked (Engine switch off) |
- |
ON (steering is unlocked) and OFF (steering is locked) appear on the screen.
If the result is not as specified, perform troubleshooting for DTCs B2285 (Steering lock position signal circuit malfunction) (See page Engine / Hybrid System>2GR-FE STARTING>SMART ENTRY AND START SYSTEM>B2285) and B2288 (Steering lock signal circuit malfunction) first (See page Engine / Hybrid System>2GR-FE STARTING>SMART ENTRY AND START SYSTEM>B2288).
OK
NG
Check if the steering lock is released when turning the engine switch on (ACC).
The steering lock is released.
OK
NG
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G60-4 (STSW) - Body ground | Brake pedal depressed, engine switch held on (ST) | Output voltage at terminal AM1 or AM2 is 2 V or more. |
If the result is not as specified, perform troubleshooting for DTC B2275 (STSW monitor malfunction) first (See page Engine / Hybrid System>2GR-FE STARTING>SMART ENTRY AND START SYSTEM>B2275).
OK
NG
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G58-3 (ACCR) - Body ground | Brake pedal depressed, shift lever N position, engine switch is pushed once → on (IG) | 0.1 to 0.8 (*1) → Output voltage at terminal AM1 or AM2 is -2 V or more. |
*1: Voltage is output only when the engine is cranking.
If the result is not as specified, perform troubleshooting for DTC B2276 (ACCR signal circuit malfunction) first (See page Engine / Hybrid System>2GR-FE STARTING>SMART ENTRY AND START SYSTEM>B2276).
OK
NG
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G57-8 (STR) - Body ground | Shift lever P position → except P position | Below 2 V → Pulse generation |
Proceed to the next step based on the inspection result.
| Result | Proceed to |
|---|---|
| NG | A |
| OK | B |
A
B
Remove the ST CUT relay.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 3 - 5 | When battery voltage is not applied to terminals 1 and 2 | 10 kΩ or higher |
| 3 - 5 | When battery voltage is applied to terminals 1 and 2 | Below 1 Ω |
OK
NG
Disconnect the A7 ECM connector.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G60-6 (STR2) - Body ground | Brake pedal depressed, shift lever P position, engine switch on (ST) | Output voltage at terminal AM1 or AM2 is -3.5 V or more (*1) |
*1: Voltage is output for 0.3 seconds when the engine is cracking to start. Disconnect the A7 connector from the ECM before measuring the voltage.
OK
NG
Disconnect the G57 and G60 ECU connectors.
Disconnect the D1 ECM connector.
Remove the ST CUT relay from the fusible link block.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G60-6 (STR2) - D1-63 (STAR) | Always | Below 1 Ω |
| G60-6 (STR2) - ST CUT relay terminal-3 | ||
| G57-8 (STR) - ST CUT relay terminal-5 | ||
| G60-6 (STR2) - Body ground | 10 kΩ or higher | |
| G57-8 (STR) - Body ground | Shift position is Except P or N | 10 kΩ or higher |
OK
NG
Disconnect the park/neutral position switch connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 4 - 9 | P | Below 1 Ω |
| 4 - 9 | N | Below 1 Ω |
| 4 - 9 | Except P and N | 10 kΩ or higher |
OK
NG
Disconnect the A7 ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G57-8 (STR) - D4-4 | Always | Below 1 Ω |
| G57-8 (STR) - Body ground | Always | 10 kΩ or higher |
| A7-48 (STA) - D4-9 | Always | Below 1 Ω |
| A7-48 (STA) - Body ground | Always | 10 kΩ or higher |
OK
NG
Remove the ST relay from the engine room relay block No. 1.
Measure the resistance according value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 3 - 5 | When battery voltage is not applied to terminals 1 and 2 | 10 kΩ or higher |
| 3 - 5 | When battery voltage is applied to terminals 1 and 2 | Below 1 Ω |
OK
NG
Remove the ST relay from the engine room relay block No. 1.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A7-48 (STA) - ST relay terminal-1 | Always | Below 1 Ω |
| A7-48 (STA) - Body ground | 10 kΩ or higher |
OK
NG
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| ST relay terminal-5 - Body ground | Always | 11 to 14 V |
| ST relay terminal-2 - Body ground | Below 1 V |
OK
NG
(See page Engine / Hybrid System>2GR-FE STARTING>STARTER>INSPECTION)
OK
NG
Reconnect the connectors.
Connect the intelligent tester to the DLC3.
When using the intelligent tester with the engine switch off, turn on and off any of the door courtesy light switches repeatedly at 1.5 second intervals or less until communication between the tester and vehicle starts.
Turn the engine switch on (IG).
| Tester Display | Measurement Item/Range | Normal Condition | Diagnostic Note |
|---|---|---|---|
| L Code Chk | L code check / OK or NG | OK: Normal
NG: Malfunction |
Electrical key in the cabin |
OK is displayed on the screen.
If the result is not as specified, refer to PROBLEM SYMPTOMS TABLE of the electrical steering lock (steering wheel cannot be unlocked) (See page Steering>STEERING COLUMN>STEERING LOCK SYSTEM>PROBLEM SYMPTOMS TABLE).
If the result is not as specified, there may be a malfunction with the steering lock ECU or the ID code box.
OK
NG
Connect the intelligent tester to the DLC3.
When using the intelligent tester with the engine switch off, turn on and off any of the door courtesy light switches repeatedly at 1.5 second intervals or less until communication between the tester and vehicle starts.
Turn the engine switch on (IG)
| Tester Display | Measurement Item/Range | Normal Condition | Diagnostic Note |
|---|---|---|---|
| Start Rqst | Start request signal response / OK or NG | OK: Received
NG: Not received |
- |
OK (received) and NG (not receive) appear on the screen.
If the result is not as specified, there may be a malfunction with the certification ECU or the ID code box.
OK
NG
Connect the intelligent tester to the DLC3.
When using the intelligent tester with the engine switch off, turn on and off any of the door courtesy light switches repeatedly at 1.5 second intervals or less until communication between the tester and vehicle starts.
Turn the engine switch on (IG).
| Tester Display | Measurement Item/Range | Normal Condition | Diagnostic Note |
|---|---|---|---|
| S Code Chk | S code check / OK or NG | OK: Normal
OFF: Malfunction |
- |
OK
NG
Check the input signal waveform.
Connect an oscilloscope to terminal G20-6 (EFIO) and body ground.
Turn the engine switch on (IG).
Check the signal waveform according to the condition(s) in the table below.
| Item | Condition |
|---|---|
| Tool setting | 10 V/DIV., 100 ms./DIV. |
| Vehicle condition | Engine switch on (IG) |
OK
NG
Replace the certification ECU.
Perform the registration procedures for the engine immobiliser system.
Check if the engine can be started.
Engine starts normally.
OK
NG