Home › Drivetrain › U660E (AUTOMATIC TRANSMISSION / TRANSAXLE) › TRANSMISSION CONTROL CABLE(for RHD) › from 2016.05
RM24M0E _52 Drivetrain _059579 U660E AUTOMATIC TRANSMISSION / TRANSAXLE _0292133 TRANSMISSION CONTROL CABLE(for RHD) A

U660E AUTOMATIC TRANSMISSION / TRANSAXLE  TRANSMISSION CONTROL CABLE(for RHD)  INSTALLATION  


PROCEDURE

Hide 33820B 1.INSTALL TRANSMISSION CONTROL CABLE ASSEMBLY

NOTICE:

Before installing the transmission control cable assembly, check that the park/neutral position switch and the shift lever are in the N position.


a.
C132236

Connect the transmission control cable to the control shaft lever with the nut.

Torque:
12 N*m (122 kgf*cm, 9 ft.*lbf)


b.
C132237

Connect the transmission control cable to the transmission control cable bracket with a new clip.


c.
C139611

Put the transmission control cable into the cabin and connect the transmission control cable with the 2 bolts.

Torque:
5.0 N*m (51 kgf*cm, 44 in.*lbf)


d.
C139610

Connect the transmission control cable clamp to the body with the 2 nuts.

Torque:
5.0 N*m (51 kgf*cm, 44 in.*lbf)


e.
C133005E07
2.229,1.813 2.354,2.052 false 1.448,0.958 1.146,0.844 false 2.302,0.844 2.646,1.042 0.344,0.198 10 false *a 2.344,2.073 2.635,2.281 0.292,0.208 10 false *b 0.969,0.729 1.5,0.917 0.531,0.188 10 false *d 1.74,0.104 2.146,0.344 0.406,0.24 10 false *c

Rotate the nut counterclockwise approximately 180°, and while holding the nut in that position, press in the stopper until it makes 2 "click" sounds.

Text in Illustration
*a Turn
*b Nut
*c Push
*d Stopper


f.
U189032E02
1.76,0.646 2.198,0.646 false 2.271,0.552 2.438,0.75 0.167,0.198 10 false A

Install the cable outer of the transmission control cable assembly to the shift lever assembly, check that the position of the spring is the same as A shown in the illustration, and press in the stopper.

HINT:

If the stopper cannot be pressed in, slightly rotate the nut clockwise and then press in the stopper.



g.
C133024E05
2.26,1.938 1.719,1.417 true 1.448,1.781 1.052,2.302 false 2.302,1.896 2.573,2.104 0.271,0.208 10 false *a 0.948,2.302 1.219,2.51 0.271,0.208 10 false *b

Using a screwdriver, pull the lock piece out from the adjuster case.

Text in Illustration
*a Lock Piece
*b Adjuster Case


h.
C137666

Connect the transmission control cable assembly to the shift lever assembly.

NOTICE:
·

Check that the lock piece is pulled up.

·

The shift lever should be in N.

·

Make sure the transmission control cable assembly is installed to the base of the pin.




i.
C139237E04
1.382,1.542 1.550,1.718 0.169,0.177 10 *a

Push the lock piece into the adjuster case.

Text in Illustration
*a Push in

NOTICE:

Securely push in the lock piece until it locks.



Hide 58151 2.INSTALL NO. 1 FRONT FLOOR HEAT INSULATOR

a.
C139609

Install the No. 1 front floor heat insulator to the body with the 3 nuts.

Torque:
6.0 N*m (61 kgf*cm, 53 in.*lbf)


Hide 17104 3.INSTALL EXHAUST MANIFOLD SUB-ASSEMBLY RH

Hide 17410 4.INSTALL CENTER EXHAUST PIPE ASSEMBLY

Hide 89465 5.INSTALL HEATED OXYGEN SENSOR (for Bank 1 Sensor 2)

Hide 74431 12.INSTALL BATTERY TRAY

Hide 53292A 15.INSTALL RADIATOR SUPPORT SEAL UPPER

Hide 51442 16.INSTALL NO. 2 ENGINE UNDER COVER

Hide 55475B 17.INSTALL CENTER INSTRUMENT CLUSTER FINISH PANEL GARNISH

Hide 55434B 18.INSTALL INSTRUMENT PANEL FINISH PANEL LOWER CENTER

Hide 58533C 19.INSTALL FLOOR CARPET COVER CENTER RH

Hide 58534E 20.INSTALL FLOOR CARPET COVER CENTER LH

Hide 55432B 21.INSTALL INSTRUMENT PANEL FINISH PANEL LOWER

Hide 55606 22.INSTALL NO. 1 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY

Hide 62111C 23.INSTALL COWL SIDE TRIM BOARD RH

Hide 67913B 24.INSTALL FRONT DOOR SCUFF PLATE RH

Hide 55607 25.INSTALL NO. 2 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY

Hide 55550 26.INSTALL GLOVE COMPARTMENT DOOR ASSEMBLY

Hide 55042B 27.INSTALL NO. 2 INSTRUMENT PANEL BOX DOOR SUB-ASSEMBLY

Hide 55041B 28.INSTALL NO. 1 INSTRUMENT PANEL BOX DOOR SUB-ASSEMBLY

Hide 29.INSTALL CENTER INSTRUMENT CLUSTER FINISH PANEL ASSEMBLY

Hide 28800 32.CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See Page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).