Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › VEHICLE STABILITY CONTROL SYSTEM › 2014.09–2016.05
RM24M0E _54 Brake _059583 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0292158 VEHICLE STABILITY CONTROL SYSTEM C

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  VEHICLE STABILITY CONTROL SYSTEM  C1273  Low Output Signal of Rear Speed Sensor RH (Test Mode DTC)  C1274  Low Output Signal of Rear Speed Sensor LH (Test Mode DTC)  C1332  Open in Rear Speed Sensor RH  C1333  Open in Rear Speed Sensor LH  C1466  Rear Speed Sensor RH  C1467  Rear Speed Sensor LH  


DESCRIPTION

Each speed sensor detects the wheel speed and sends signals to the skid control ECU (brake actuator assembly). These signals are used by the ABS.

The speed sensor rotors have rows of alternating N and S magnetic poles. The speed sensors use the frequency of output pulses to detect the vehicle speed. Because the sensor outputs digital pulses, it can detect the vehicle speed even when the vehicle is nearly stationary.

DTCs C1273 and C1274 are cleared when the speed sensor sends a vehicle speed signal or when Test Mode ends. DTCs C1273 and C1274 are output only in Test Mode.

C151818E60
5.604,1.344 6.021,1.344 false 1.396,0.5 1.573,0.865 false 0.5,0.375 1.427,0.542 0.927,0.167 10 false Speed Sensor 4.042,2.073 4.75,2.24 0.708,0.167 10 false Low speed 6.083,1.26 6.448,1.427 0.365,0.167 10 false 0.3 V 6.083,1.625 6.573,1.802 0.49,0.177 10 false 0.15 V 4.979,2.073 5.719,2.281 0.74,0.208 10 false High speed 0.969,2.177 2.26,2.344 1.292,0.167 10 false Speed Sensor Rotor

DTC No. Detection Item DTC Detection Condition Trouble Area
C1273 Low Output Signal of Rear Speed Sensor RH (Test Mode DTC) Detected only during Test Mode.
·

Rear speed sensor RH

·

Sensor installation

·

Rear speed sensor rotor RH (rear axle hub and bearing assembly RH)


C1274 Low Output Signal of Rear Speed Sensor LH (Test Mode DTC) Detected only during Test Mode.
·

Rear speed sensor LH

·

Sensor installation

·

Rear speed sensor rotor LH (rear axle hub and bearing assembly LH)


C1332 Open in Rear Speed Sensor RH An open or short in the speed sensor signal circuit.
·

Rear speed sensor RH

·

Speed sensor circuit

·

Sensor installation


C1333 Open in Rear Speed Sensor LH An open or short in the speed sensor signal circuit.
·

Rear speed sensor LH

·

Speed sensor circuit

·

Sensor installation


C1466 Rear Speed Sensor RH Any of the following is detected:
1.

The vehicle speed is more than 50.4 km/h (31 mph) and pulses are not input for 0.4 seconds.

2.

After the initial start or restart and when the vehicle speed has reached 12 km/h (7 mph), a wheel speed of 0 km/h (0 mph) is detected.

3.

After the initial start or restart and when the vehicle speed has reached 20 km/h (12 mph), a rear wheel speed of 0 km/h (0 mph) is detected.

4.

The following conditions are met for 9 to 72 seconds or more (varies depending on the driving conditions):

-

The difference between the speed of the fastest wheel and the speed of the slowest wheel is 5% or more of vehicle speed. (If the speed of any wheel is less than 5 km/h (3 mph), a speed difference of up to 15% is allowable.)

-

The vehicle speed is less than 100 km/h (62 mph) and the difference between the speed of the fastest wheel and the speed of the slowest wheel is 5 km/h (3 mph) or more. (If the speed of any wheel is less than 5 km/h (3 mph), a speed difference of up to 16 km/h (10 mph) is allowable.)

-

The vehicle speed is 100 km/h (62 mph) or more and the difference between the speed of the fastest wheel and the speed of the slowest wheel is 6% or more of vehicle speed. (If the speed of any wheel is less than 5 km/h (3 mph), a speed difference of up to 15% is allowable.)


5.

Wheel speed sensor signal fluctuation is equivalent to 98 G or more, or alternates between 50 G or more and -50 G or less.

6.

An abnormal signal is received from a wheel speed sensor.


·

Rear speed sensor RH

·

Speed sensor circuit

·

Rear speed sensor rotor RH (rear axle hub and bearing assembly RH)

·

Sensor installation

·

Skid control ECU (brake actuator assembly)


C1467 Rear Speed Sensor LH Any of the following is detected:
1.

The vehicle speed is more than 50.4 km/h (31 mph) and pulses are not input for 0.4 seconds.

2.

After the initial start or restart and when the vehicle speed has reached 12 km/h (7 mph), a wheel speed of 0 km/h (0 mph) is detected.

3.

After the initial start or restart and when the vehicle speed has reached 20 km/h (12 mph), a rear wheel speed of 0 km/h (0 mph) is detected.

4.

The following conditions are met for 9 to 72 seconds or more (varies depending on the driving conditions):

-

The difference between the speed of the fastest wheel and the speed of the slowest wheel is 5% or more of vehicle speed. (If the speed of any wheel is less than 5 km/h (3 mph), a speed difference of up to 15% is allowable.)

-

The vehicle speed is less than 100 km/h (62 mph) and the difference between the speed of the fastest wheel and the speed of the slowest wheel is 5 km/h (3 mph) or more. (If the speed of any wheel is less than 5 km/h (3 mph), a speed difference of up to 16 km/h (10 mph) is allowable.)

-

The vehicle speed is 100 km/h (62 mph) or more and the difference between the speed of the fastest wheel and the speed of the slowest wheel is 6% or more of vehicle speed. (If the speed of any wheel is less than 5 km/h (3 mph), a speed difference of up to 15% is allowable.)


5.

Wheel speed sensor signal fluctuation is equivalent to 98 G or more, or alternates between 50 G or more and -50 G or less.

6.

An abnormal signal is received from a wheel speed sensor.


·

Rear speed sensor LH

·

Speed sensor circuit

·

Rear speed sensor rotor LH (rear axle hub and bearing assembly LH)

·

Sensor installation

·

Skid control ECU (brake actuator assembly)



HINT:
·

DTCs C1273, C1332 and C1466 are for the rear speed sensor RH.

·

DTCs C1274, C1333 and C1467 are for the rear speed sensor LH.



WIRING DIAGRAM

C266976E34
5.5,4.042 7.115,4.49 1.615,0.448 10 false Skid Control ECU (Brake Actuator Assembly) 5.51,3.875 5.969,4.073 0.458,0.198 10 false A35 1.438,1.635 2.469,2 1.031,0.365 10 false Skid Control Sensor Wire RH 1.49,3.667 2.479,4.052 0.99,0.385 10 false Skid Control Sensor Wire LH 0.365,1.625 1.188,1.969 0.823,0.344 10 false Rear Speed Sensor RH 0.375,3.667 1.167,4.063 0.792,0.396 10 false Rear Speed Sensor LH 0.75,0.625 1.104,0.875 0.354,0.25 10 false RR+ 0.76,1.208 1.094,1.427 0.333,0.219 10 false RR- 1.948,0.625 2.333,0.917 0.385,0.292 10 false RR+ 1.563,0.625 2.021,0.823 0.458,0.198 10 false RR+ 1.563,1.198 1.917,1.417 0.354,0.219 10 false RR- 1.958,1.208 2.25,1.438 0.292,0.229 10 false RR- 2.427,0.417 2.583,0.615 0.156,0.198 10 false 1 1.26,0.417 1.417,0.615 0.156,0.198 10 false 2 1.26,0.99 1.417,1.188 0.156,0.198 10 false 1 2.427,0.99 2.583,1.188 0.156,0.198 10 false 2 1.24,0.625 1.469,0.823 0.229,0.198 10 false c1 1.229,1.208 1.469,1.406 0.24,0.198 10 false c1 2.344,0.625 2.656,0.823 0.313,0.198 10 false cN1 2.354,1.208 2.667,1.406 0.313,0.198 10 false cN1 0.76,2.667 1.125,2.896 0.365,0.229 10 false RL+ 1.583,2.656 2.042,2.854 0.458,0.198 10 false RL+ 1.958,2.656 2.323,2.917 0.365,0.26 10 false RL+ 0.76,3.25 1.083,3.5 0.323,0.25 10 false RL- 1.583,3.24 1.833,3.5 0.25,0.26 10 false RL- 1.958,3.24 2.25,3.5 0.292,0.26 10 false RL- 1.24,2.656 1.396,2.938 0.156,0.281 10 false d1 1.219,3.24 1.385,3.49 0.167,0.25 10 false d1 1.25,2.438 1.406,2.635 0.156,0.198 10 false 2 2.427,2.438 2.583,2.635 0.156,0.198 10 false 1 2.344,2.646 2.656,2.844 0.313,0.198 10 false dM1 2.344,3.24 2.656,3.438 0.313,0.198 10 false dM1 1.25,3.01 1.406,3.208 0.156,0.198 10 false 1 2.417,3.021 2.573,3.219 0.156,0.198 10 false 2 5.688,0.521 6,0.719 0.313,0.198 10 false 17 5.688,1.083 6,1.281 0.313,0.198 10 false 29 6,0.625 6.458,0.823 0.458,0.198 10 false RR+ 6,1.188 6.458,1.385 0.458,0.198 10 false RR- 6,2.656 6.458,2.854 0.458,0.198 10 false RL+ 6,3.219 6.458,3.417 0.458,0.198 10 false RL- 5.688,2.552 6,2.75 0.313,0.198 10 false 31 5.688,3.115 6,3.313 0.313,0.198 10 false 18

CAUTION / NOTICE / HINT

NOTICE:

When replacing the skid control ECU (brake actuator assembly), perform system variant learning and acceleration sensor zero point calibration (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>CALIBRATION).


PROCEDURE

1.READ VALUE USING GTS (REAR SPEED SENSOR)
a.

Connect the GTS to the DLC3.


b.

Start the engine.


c.

Select the Data List using the GTS (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>DATA LIST / ACTIVE TEST).

ABS/VSC/TRC
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
RR Wheel Speed Rear wheel speed sensor RH reading / Min.: 0 km/h (0 mph), Max.: 326 km/h (202 mph) Vehicle stopped: 0 km/h (0 mph) When driving at constant speed: No large fluctuations
RL Wheel Speed Rear wheel speed sensor LH reading / Min.: 0 km/h (0 mph), Max.: 326 km/h (202 mph) Vehicle stopped: 0 km/h (0 mph) When driving at constant speed: No large fluctuations


d.

Check the speed value output from the speed sensor displayed on the GTS.

HINT:

Factors that affect the indicated vehicle speed include tire size, tire pressure, and tire wear. The speed indicated on the speedometer has an allowable margin of error. This can be tested using a speedometer tester (calibrated chassis dynamometer). For details about testing and the margin of error, see the reference chart (See page Vehicle Interior>METER / GAUGE / DISPLAY>METER / GAUGE SYSTEM>ON-VEHICLE INSPECTION).




OK

2.PERFORM TEST MODE INSPECTION (SIGNAL CHECK)

NG

4.CHECK REAR SPEED SENSOR INSTALLATION
2.PERFORM TEST MODE INSPECTION (SIGNAL CHECK)
a.

Turn the engine switch off.


b.

Perform the sensor check using the Test Mode procedure (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>TEST MODE PROCEDURE).

OK:

No Test Mode DTCs are output.




OK

3.RECONFIRM DTC

NG

4.CHECK REAR SPEED SENSOR INSTALLATION
3.RECONFIRM DTC
a.

Turn the engine switch off.



c.

Turn the engine switch off.


d.

Start the engine.


e.

Drive the vehicle at a speed of 54 km/h (34 mph) or more for at least 120 seconds.



Result:
Result Proceed to
DTCs C1332, C1333, C1466 and C1467 are not output. A
DTCs C1332, C1333, C1466 and/or C1467 are output. B



A

B

8.REPLACE REAR AXLE HUB AND BEARING ASSEMBLY
4.CHECK REAR SPEED SENSOR INSTALLATION
a.
C210569E06
1.24,0.24 0.979,0.438 false 0.865,1.75 1.198,1.927 0.333,0.177 10 false *a 2.344,1.75 2.677,1.927 0.333,0.177 10 false *b 0.115,0.115 0.427,0.313 0.313,0.198 10 false *1 1.24,0.094 1.552,0.292 0.313,0.198 10 false *c

Turn the engine switch off.


b.

Check the speed sensor installation.

OK:

There is no clearance between the sensor and rear axle carrier.


Text in Illustration
*1 Rear Speed Sensor
*a Correct
*b Incorrect
*c No clearance



OK

5.INSPECT SKID CONTROL SENSOR WIRE

NG

5.INSPECT SKID CONTROL SENSOR WIRE
a.
U189649E02
0.958,1.219 0.708,2 false 1.198,1.219 1.385,2.021 false 2.365,1.49 2.188,2.052 false 2.615,1.5 2.781,2.042 false 0.958,3.292 0.708,4.083 false 1.198,3.302 1.396,4.094 false 2.365,3.563 2.188,4.115 false 2.635,3.563 2.802,4.115 false 0.146,0.073 0.396,0.302 0.25,0.229 10 false *a 0.146,0.281 0.396,0.458 0.25,0.177 10 false *A 0.958,0.438 1.208,0.615 0.25,0.177 10 false *b 2.385,0.698 2.635,0.875 0.25,0.177 10 false *c 0.958,2.521 1.208,2.698 0.25,0.177 10 false *b 2.385,2.781 2.635,2.958 0.25,0.177 10 false *c 0.563,2.073 0.917,2.25 0.354,0.177 10 false RR- 2.729,2.073 3.083,2.25 0.354,0.177 10 false RR- 1.25,2.073 1.604,2.25 0.354,0.177 10 false RR+ 2.042,2.073 2.396,2.25 0.354,0.177 10 false RR+ 0.563,4.135 0.917,4.313 0.354,0.177 10 false RL- 2.729,4.135 3.083,4.313 0.354,0.177 10 false RL- 1.25,4.135 1.604,4.313 0.354,0.177 10 false RL+ 2.042,4.135 2.396,4.313 0.354,0.177 10 false RL+ 0.313,2.688 0.49,2.844 0.177,0.156 10 false d1 0.323,0.635 0.5,0.792 0.177,0.156 10 false c1 1.844,0.646 2.135,0.802 0.292,0.156 10 false cN1 1.833,2.698 2.135,2.854 0.302,0.156 10 false dM1 0.146,2.281 0.396,2.458 0.25,0.177 10 false *B

Make sure that there is no looseness at the locking part and the connecting part of the connectors.


b.

Remove the skid control sensor wire.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for RH
Tester Connection Condition Specified Condition
c1-2 (RR+) - cN1-1 (RR+) Always Below 1 Ω
c1-2 (RR+) - cN1-2 (RR-) Always 10 kΩ or higher
c1-2 (RR+) or cN1-1 (RR+) - Body ground Always 10 kΩ or higher
c1-1 (RR-) - cN1-2 (RR-) Always Below 1 Ω
c1-1 (RR-) - cN1-1 (RR+) Always 10 kΩ or higher
c1-1 (RR-) or cN1-2 (RR-) - Body ground Always 10 kΩ or higher

for LH
Tester Connection Condition Specified Condition
d1-2 (RL+) - dM1-1 (RL+) Always Below 1 Ω
d1-2 (RL+) - dM1-2 (RL-) Always 10 kΩ or higher
d1-2 (RL+) or dM1-1 (RL+) - Body ground Always 10 kΩ or higher
d1-1 (RL-) - dM1-2 (RL-) Always Below 1 Ω
d1-1 (RL-) - dM1-1 (RL+) Always 10 kΩ or higher
d1-1 (RL-) or dM1-2 (RL-) - Body ground Always 10 kΩ or higher


Text in Illustration
*A for RH
*B for LH
*a Front view of skid control sensor wire
*b Front view of wire harness connector
(to Sensor Side Connector)
*c Front view of wire harness connector
(to Vehicle Side Connector)

NOTICE:

Check the speed sensor signal after replacement (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>TEST MODE PROCEDURE).




OK

6.CHECK HARNESS AND CONNECTOR (BRAKE ACTUATOR ASSEMBLY - SKID CONTROL SENSOR WIRE)

NG

6.CHECK HARNESS AND CONNECTOR (BRAKE ACTUATOR ASSEMBLY - SKID CONTROL SENSOR WIRE)
a.

Make sure that there is no looseness at the locking part and the connecting part of the connector.


b.

Disconnect the A35 skid control ECU (brake actuator assembly) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for RH
Tester Connection Condition Specified Condition
A35-17 (RR+) - cN1-1 (RR+) Always Below 1 Ω
A35-17 (RR+) or cN1-1 (RR+) - Body ground Always 10 kΩ or higher
A35-29 (RR-) - cN1-2 (RR-) Always Below 1 Ω
A35-29 (RR-) or cN1-2 (RR-) - Body ground Always 10 kΩ or higher

for LH
Tester Connection Condition Specified Condition
A35-31 (RL+) - dM1-1 (RL+) Always Below 1 Ω
A35-31 (RL+) or dM1-1 (RL+) - Body ground Always 10 kΩ or higher
A35-18 (RL-) - dM1-2 (RL-) Always Below 1 Ω
A35-18 (RL-) or dM1-2 (RL-) - Body ground Always 10 kΩ or higher




OK

7.RECONFIRM DTC

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

7.RECONFIRM DTC
a.

Install the skid control sensor wire.


b.

Reconnect the A35 skid control ECU (brake actuator assembly) connector.



d.

Turn the engine switch off.


e.

Start the engine.


f.

Drive the vehicle at a speed of 54 km/h (34 mph) or more for at least 120 seconds.



Result:
Result Proceed to
DTCs C1332, C1333, C1466 and/or C1467 are output. A
DTCs C1332, C1333, C1466 and C1467 are not output. B



A

8.REPLACE REAR AXLE HUB AND BEARING ASSEMBLY

B

8.REPLACE REAR AXLE HUB AND BEARING ASSEMBLY
a.

Turn the engine switch off.


b.

Replace the rear speed sensor rotor with rear speed sensor (rear axle hub and bearing assembly) (See page Drivetrain>AXLE>REAR AXLE HUB>REMOVAL).

HINT:

The rear speed sensor rotor is incorporated into the rear axle hub and bearing assembly. If the rear speed sensor rotor needs to be replaced, replace the rear axle hub and bearing assembly with rear speed sensor.


NOTICE:

Check the speed sensor signal after replacement (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>TEST MODE PROCEDURE).




NEXT

9.RECONFIRM DTC
9.RECONFIRM DTC

b.

Turn the engine switch off.


c.

Start the engine.


d.

Drive the vehicle at a speed of 54 km/h (34 mph) or more for at least 120 seconds.


e.

Check if the same DTC is output (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>DTC CHECK / CLEAR).

Result:
Result Proceed to
DTCs C1332, C1333, C1466 and C1467 are not output. A
DTCs C1332, C1333, C1466 and/or C1467 are output. B


HINT:

If troubleshooting has been carried out according to Problem Symptoms Table, refer back to the table and proceed to the next step before replacing parts (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>PROBLEM SYMPTOMS TABLE).




A

END

B