Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › VEHICLE STABILITY CONTROL SYSTEM › 2014.09–2016.05
RM24M0E _54 Brake _059583 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0292158 VEHICLE STABILITY CONTROL SYSTEM C

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  VEHICLE STABILITY CONTROL SYSTEM  C1237  Speed Sensor Rotor Faulty  C1275  Abnormal Change in Output Signal of Front Speed Sensor RH (Test Mode DTC)  C1276  Abnormal Change in Output Signal of Front Speed Sensor LH (Test Mode DTC)  C1277  Abnormal Change in Output Signal of Rear Speed Sensor RH (Test Mode DTC)  C1278  Abnormal Change in Output Signal of Rear Speed Sensor LH (Test Mode DTC)  


DESCRIPTION

The skid control ECU (brake actuator assembly) measures the speed of each wheel by receiving signals from each speed sensor.

These signals are used for recognizing that all four wheels are operating properly.

Therefore, signals from all wheels must be equal.

DTCs C1275 to C1278 are cleared when the speed sensor sends a vehicle speed signal or when Test Mode ends. DTCs C1275 to C1278 are output only in Test Mode.

DTC No. Detection Item DTC Detection Condition Trouble Area
C1237 Speed Sensor Rotor Faulty Any of the following is detected:
1.

Discrepancy among four wheel speed sensor output.

2.

Abnormal pulse signals from 3 or more sensors.

3.

Continuous ABS control is performed for 60 seconds or more.

4.

VSC control is performed for 5 seconds or more.


·

Tire and wheel size

·

Tire deformation

·

Speed sensor rotor

·

Speed sensor

·

Speed sensor circuit

·

Skid control ECU (brake actuator assembly)


C1275 Abnormal Change in Output Signal of Front Speed Sensor RH (Test Mode DTC) Detected only during Test Mode. Front speed sensor rotor RH (front axle hub sub-assembly RH)
C1276 Abnormal Change in Output Signal of Front Speed Sensor LH (Test Mode DTC) Detected only during Test Mode. Front speed sensor rotor LH (front axle hub sub-assembly LH)
C1277 Abnormal Change in Output Signal of Rear Speed Sensor RH (Test Mode DTC) Detected only during Test Mode. Rear speed sensor rotor RH (rear axle hub and bearing assembly RH)
C1278 Abnormal Change in Output Signal of Rear Speed Sensor LH (Test Mode DTC) Detected only during Test Mode. Rear speed sensor rotor LH (rear axle hub and bearing assembly LH)

HINT:
·

DTC C1275 is for the front speed sensor RH.

·

DTC C1276 is for the front speed sensor LH.

·

DTC C1277 is for the rear speed sensor RH.

·

DTC C1278 is for the rear speed sensor LH.



WIRING DIAGRAM

CAUTION / NOTICE / HINT

NOTICE:

When replacing the skid control ECU (brake actuator assembly), perform system variant learning and acceleration sensor zero point calibration (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>CALIBRATION).


HINT:

When C1330, C1331, C1332, C1333, C1464, C1465, C1466 and/or C1467 is output together with C1237, inspect and repair the trouble areas indicated by C1330, C1331, C1332, C1333, C1464, C1465, C1466 and/or C1467 first (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>C1271 for C1330, C1331, C1464 and C1465, and Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>C1273 for C1332, C1333, C1466 and C1467).


PROCEDURE

1.CHECK TIRES
a.

Check the size and condition of all four tires (See page Drivetrain>TIRE AND WHEEL>TIRE AND WHEEL SYSTEM>INSPECTION).

HINT:

The DTC is output when tire deformation or a difference in tire size is detected.


OK:

The diameter of all four tires and the tire pressure are the same.




OK

2.READ VALUE USING GTS (SPEED SENSOR)

NG

REPLACE TIRES SO THAT ALL FOUR TIRES ARE THE SAME SIZE

2.READ VALUE USING GTS (SPEED SENSOR)
a.

Connect the GTS to the DLC3.


b.

Start the engine.


c.

Select the Data List using the GTS (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>DATA LIST / ACTIVE TEST).

ABS/VSC/TRC
Tester Display Measurement Item / Range Normal Condition Diagnostic Note
FR Wheel Speed Front wheel speed sensor RH reading / Min.: 0 km/h (0 mph), Max.: 326 km/h (202 mph) Vehicle stopped: 0 km/h (0 mph) When driving at constant speed: No large fluctuations
FL Wheel Speed Front wheel speed sensor LH reading / Min.: 0 km/h (0 mph), Max.: 326 km/h (202 mph) Vehicle stopped: 0 km/h (0 mph) When driving at constant speed: No large fluctuations
RR Wheel Speed Rear wheel speed sensor RH reading / Min.: 0 km/h (0 mph), Max.: 326 km/h (202 mph) Vehicle stopped: 0 km/h (0 mph) When driving at constant speed: No large fluctuations
RL Wheel Speed Rear wheel speed sensor LH reading / Min.: 0 km/h (0 mph), Max.: 326 km/h (202 mph) Vehicle stopped: 0 km/h (0 mph) When driving at constant speed: No large fluctuations


d.

Check the speed value output from the speed sensor displayed on the GTS.

HINT:

Factors that affect the indicated vehicle speed include tire size, tire pressure, and tire wear. The speed indicated on the speedometer has an allowable margin of error. This can be tested using a speedometer tester (calibrated chassis dynamometer). For details about testing and the margin of error, see the reference chart (See page Vehicle Interior>METER / GAUGE / DISPLAY>METER / GAUGE SYSTEM>ON-VEHICLE INSPECTION).


OK:

The speed value output from the speed sensor displayed on the GTS is similar to the speed indicated on the speedometer.



Result:
Result Proceed to
OK A
NG (for front) B
NG (for rear) C



A

3.PERFORM TEST MODE INSPECTION (SIGNAL CHECK)

B

5.CHECK FRONT SPEED SENSOR AND SENSOR ROTOR

C

12.INSPECT SKID CONTROL SENSOR WIRE
3.PERFORM TEST MODE INSPECTION (SIGNAL CHECK)
a.

Turn the engine switch off.


b.

Perform the sensor check using Test Mode Procedure (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>TEST MODE PROCEDURE).

OK:

All Test Mode DTCs are not output.



Result:
Result Proceed to
OK A
NG (for front) B
NG (for rear) C



A

4.RECONFIRM DTC

B

5.CHECK FRONT SPEED SENSOR AND SENSOR ROTOR

C

12.INSPECT SKID CONTROL SENSOR WIRE
4.RECONFIRM DTC
a.

Turn the engine switch off.



c.

Turn the engine switch off.


d.

Start the engine.


e.

Drive the vehicle at a speed of 54 km/h (34 mph) or more for at least 120 seconds.



Result:
Result Proceed to
DTC C1237 is not output. A
DTC C1237 is output (for front). B
DTC C1237 is output (for rear). C



A

B

8.REPLACE FRONT SPEED SENSOR

C

15.REPLACE REAR AXLE HUB AND BEARING ASSEMBLY WITH REAR SPEED SENSOR
5.CHECK FRONT SPEED SENSOR AND SENSOR ROTOR
a.

Remove the front speed sensor and the component with the sensor rotor (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>FRONT SPEED SENSOR>REMOVAL for speed sensor, and Drivetrain>AXLE>FRONT AXLE HUB>REMOVAL for sensor rotor).


b.

Check the speed sensor tip and speed sensor rotor.

OK:

No scratches, oil, or foreign matter on the sensor tip and rotor.


NOTICE:
·

If no damage to the speed sensor tip is found during this inspection, do not replace the speed sensor.

If there are any ferrous metal filings stuck to the rotor, this will result in a malfunction, so confirm that the rotor is not contaminated with foreign matter before replacing the sensor.

·

Check the speed sensor signal after cleaning or replacement (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>TEST MODE PROCEDURE).





OK

6.CHECK HARNESS AND CONNECTOR (BRAKE ACTUATOR ASSEMBLY - FRONT SPEED SENSOR)

NG

CLEAN OR REPLACE FRONT SPEED SENSOR OR COMPONENT WITH SENSOR ROTOR

6.CHECK HARNESS AND CONNECTOR (BRAKE ACTUATOR ASSEMBLY - FRONT SPEED SENSOR)
a.

Install the front speed sensor and the component with the sensor rotor.


b.

Make sure that there is no looseness at the locking part and the connecting part of the connectors.


c.

Disconnect the A35 skid control ECU (brake actuator assembly) connector and A5 or A20 front speed sensor connector.


d.

Measure the resistance according to the value(s) in the table below.


Standard Resistance:
for RH
Tester Connection Condition Specified Condition
A35-16 (FR+) - A20-2 (FR+) Always Below 1 Ω
A35-16 (FR+) or A20-2 (FR+) - Body ground Always 10 kΩ or higher
A35-4 (FR-) - A20-1 (FR-) Always Below 1 Ω
A35-4 (FR-) or A20-1 (FR-) - Body ground Always 10 kΩ or higher

for LH
Tester Connection Condition Specified Condition
A35-19 (FL+) - A5-2 (FL+) Always Below 1 Ω
A35-19 (FL+) or A5-2 (FL+) - Body ground Always 10 kΩ or higher
A35-8 (FL-) - A5-1 (FL-) Always Below 1 Ω
A35-8 (FL-) or A5-1 (FL-) - Body ground Always 10 kΩ or higher



OK

7.RECONFIRM DTC

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

7.RECONFIRM DTC
a.

Reconnect the A35 skid control ECU (brake actuator assembly) connector and A5 or A20 front speed sensor connector.



c.

Turn the engine switch off.


d.

Start the engine.


e.

Drive the vehicle at a speed of 54 km/h (34 mph) or more for at least 120 seconds.



Result:
Result Proceed to
DTC C1237 is output. A
DTC C1237 is not output. B



A

8.REPLACE FRONT SPEED SENSOR

B

8.REPLACE FRONT SPEED SENSOR
a.

Turn the engine switch off.


b.

Replace the front speed sensor (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>FRONT SPEED SENSOR>REMOVAL).

NOTICE:

Check the speed sensor signal after replacement (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>TEST MODE PROCEDURE).




NEXT

9.RECONFIRM DTC
9.RECONFIRM DTC

b.

Turn the engine switch off.


c.

Start the engine.


d.

Drive the vehicle at a speed of 54 km/h (34 mph) or more for at least 120 seconds.



Result:
Result Proceed to
DTC C1237 is output. A
DTC C1237 is not output. B



A

10.REPLACE FRONT AXLE HUB SUB-ASSEMBLY

B

END

10.REPLACE FRONT AXLE HUB SUB-ASSEMBLY
a.

Turn the engine switch off.


b.

Replace the front speed sensor rotor (front axle hub sub-assembly) (See page Drivetrain>AXLE>FRONT AXLE HUB>REMOVAL).

HINT:

The front speed sensor rotor is incorporated into the front axle hub sub-assembly. If the front speed sensor rotor needs to be replaced, replace the front axle hub sub-assembly.


NOTICE:

Check the speed sensor signal after replacement (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>TEST MODE PROCEDURE).




NEXT

11.RECONFIRM DTC
11.RECONFIRM DTC

b.

Turn the engine switch off.


c.

Start the engine.


d.

Drive the vehicle at a speed of 54 km/h (34 mph) or more for at least 120 seconds.



Result:
Result Proceed to
DTC C1237 is output. A
DTC C1237 is not output. B



A

B

END

12.INSPECT SKID CONTROL SENSOR WIRE
a.
U189649E02
0.958,1.219 0.708,2 false 1.198,1.219 1.385,2.021 false 2.365,1.49 2.188,2.052 false 2.615,1.5 2.781,2.042 false 0.958,3.292 0.708,4.083 false 1.198,3.302 1.396,4.094 false 2.365,3.563 2.188,4.115 false 2.635,3.563 2.802,4.115 false 0.146,0.073 0.396,0.302 0.25,0.229 10 false *a 0.146,0.281 0.396,0.458 0.25,0.177 10 false *A 0.958,0.438 1.208,0.615 0.25,0.177 10 false *b 2.385,0.698 2.635,0.875 0.25,0.177 10 false *c 0.958,2.521 1.208,2.698 0.25,0.177 10 false *b 2.385,2.781 2.635,2.958 0.25,0.177 10 false *c 0.563,2.073 0.917,2.25 0.354,0.177 10 false RR- 2.729,2.073 3.083,2.25 0.354,0.177 10 false RR- 1.25,2.073 1.604,2.25 0.354,0.177 10 false RR+ 2.042,2.073 2.396,2.25 0.354,0.177 10 false RR+ 0.563,4.135 0.917,4.313 0.354,0.177 10 false RL- 2.729,4.135 3.083,4.313 0.354,0.177 10 false RL- 1.25,4.135 1.604,4.313 0.354,0.177 10 false RL+ 2.042,4.135 2.396,4.313 0.354,0.177 10 false RL+ 0.313,2.688 0.49,2.844 0.177,0.156 10 false d1 0.323,0.635 0.5,0.792 0.177,0.156 10 false c1 1.844,0.646 2.135,0.802 0.292,0.156 10 false cN1 1.833,2.698 2.135,2.854 0.302,0.156 10 false dM1 0.146,2.281 0.396,2.458 0.25,0.177 10 false *B

Make sure that there is no looseness at the locking part and the connecting part of the connectors.


b.

Remove the skid control sensor wire.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for RH
Tester Connection Condition Specified Condition
c1-2 (RR+) - cN1-1 (RR+) Always Below 1 Ω
c1-2 (RR+) - cN1-2 (RR-) Always 10 kΩ or higher
c1-2 (RR+) or cN1-1 (RR+) - Body ground Always 10 kΩ or higher
c1-1 (RR-) - cN1-2 (RR-) Always Below 1 Ω
c1-1 (RR-) - cN1-1 (RR+) Always 10 kΩ or higher
c1-1 (RR-) or cN1-2 (RR-) - Body ground Always 10 kΩ or higher

for LH
Tester Connection Condition Specified Condition
d1-2 (RL+) - dM1-1 (RL+) Always Below 1 Ω
d1-2 (RL+) - dM1-2 (RL-) Always 10 kΩ or higher
d1-2 (RL+) or dM1-1 (RL+) - Body ground Always 10 kΩ or higher
d1-1 (RL-) - dM1-2 (RL-) Always Below 1 Ω
d1-1 (RL-) - dM1-1 (RL+) Always 10 kΩ or higher
d1-1 (RL-) or dM1-2 (RL-) - Body ground Always 10 kΩ or higher


Text in Illustration
*A for RH
*B for LH
*a Front view of skid control sensor wire
*b Front view of wire harness connector
(to Sensor Side Connector)
*c Front view of wire harness connector
(to Vehicle Side Connector)

NOTICE:

Check the speed sensor signal after replacement (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>TEST MODE PROCEDURE).




OK

13.CHECK HARNESS AND CONNECTOR (BRAKE ACTUATOR ASSEMBLY - SKID CONTROL SENSOR WIRE)

NG

13.CHECK HARNESS AND CONNECTOR (BRAKE ACTUATOR ASSEMBLY - SKID CONTROL SENSOR WIRE)
a.

Make sure that there is no looseness at the locking part and the connecting part of the connector.


b.

Disconnect the A35 skid control ECU (brake actuator assembly) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for RH
Tester Connection Condition Specified Condition
A35-17 (RR+) - cN1-1 (RR+) Always Below 1 Ω
A35-17 (RR+) or cN1-1 (RR+) - Body ground Always 10 kΩ or higher
A35-29 (RR-) - cN1-2 (RR-) Always Below 1 Ω
A35-29 (RR-) or cN1-2 (RR-) - Body ground Always 10 kΩ or higher

for LH
Tester Connection Condition Specified Condition
A35-31 (RL+) - dM1-1 (RL+) Always Below 1 Ω
A35-31 (RL+) or dM1-1 (RL+) - Body ground Always 10 kΩ or higher
A35-18 (RL-) - dM1-2 (RL-) Always Below 1 Ω
A35-18 (RL-) or dM1-2 (RL-) - Body ground Always 10 kΩ or higher




OK

14.RECONFIRM DTC

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

14.RECONFIRM DTC
a.

Install the skid control sensor wire.


b.

Reconnect the A35 skid control ECU (brake actuator assembly) connector.



d.

Turn the engine switch off.


e.

Start the engine.


f.

Drive the vehicle at a speed of 54 km/h (34 mph) or more for at least 120 seconds.



Result:
Result Proceed to
DTC C1237 is output. A
DTC C1237 is not output. B



A

15.REPLACE REAR AXLE HUB AND BEARING ASSEMBLY WITH REAR SPEED SENSOR

B

15.REPLACE REAR AXLE HUB AND BEARING ASSEMBLY WITH REAR SPEED SENSOR
a.

Turn the engine switch off.


b.

Replace the rear speed sensor rotor with rear speed sensor (rear axle hub and bearing assembly) (See page Drivetrain>AXLE>REAR AXLE HUB>REMOVAL).

HINT:

The rear speed sensor rotor is incorporated into the rear axle hub and bearing assembly.

If the rear speed sensor rotor needs to be replaced, replace the rear axle hub and bearing assembly with rear speed sensor.


NOTICE:

Check the speed sensor signal after replacement (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>TEST MODE PROCEDURE).




NEXT

16.RECONFIRM DTC
16.RECONFIRM DTC

b.

Turn the engine switch off.


c.

Start the engine.


d.

Drive the vehicle at a speed of 54 km/h (34 mph) or more for at least 120 seconds.



Result:
Result Proceed to
DTC C1237 is output. A
DTC C1237 is not output. B



A

B

END