2011-2016 FJ Cruiser · Service Manual ENGINE

P0014 Camshaft Position "B" - Timing Over-Advanced or System Performance (Bank 1)

Diagnostic trouble codes · Vehicles built from Aug 2014

Also covers:

Versions by build date: Aug 2009 – Oct 2010 Nov 2010 – Jul 2014 from Aug 2014

DESCRIPTION

HINT:
If DTC P0014, P0015, P0024 or P0025 is present, check the VVT (Variable Valve Timing) system.

The VVT (Variable Valve Timing) system includes the ECM, Camshaft Timing Oil Control Valve (OCV) assembly and camshaft timing exhaust gear assembly. The ECM sends a target duty-cycle control signal to the OCV. This control signal regulates the oil pressure supplied to the camshaft timing exhaust gear assembly. Camshaft timing control is performed according to engine operating conditions such as the intake air volume, throttle valve position and engine coolant temperature. The ECM controls the OCV based on the signals transmitted by several sensors. The camshaft timing exhaust gear assembly regulates the exhaust camshaft angle using oil pressure through the OCV. As a result, the relative positions of the camshaft and crankshaft are optimized, the engine torque and fuel economy improve, and the exhaust emissions decrease under overall driving conditions. The ECM detects the actual exhaust valve timing using signals from the camshaft and crankshaft position sensors, and performs feedback control. This is how the target exhaust valve timing is verified by the ECM.
A209140E10
DTC No.
DTC Detection Condition
Trouble Area
P0014
P0024
Exhaust valve timing is not adjusted in valve timing advance range
(2 trip detection logic)
  1. Valve timing
  2. Camshaft Timing Oil control valve (OCV) assembly (for exhaust side)
  3. OCV filter
  4. Camshaft timing exhaust gear assembly
  5. ECM
P0015
P0025
Exhaust valve timing is not adjusted in valve timing retard range
(1 trip detection logic)
  1. Valve timing
  2. OCV (for exhaust side)
  3. OCV filter
  4. Camshaft timing exhaust gear assembly
  5. ECM

MONITOR DESCRIPTION

The ECM optimizes the exhaust valve timing using the VVT (Variable Valve Timing) system to control the exhaust camshaft. The VVT system includes the ECM, Camshaft Timing Oil Control Valve (OCV) assembly and camshaft timing exhaust gear assembly.
The ECM sends a target duty-cycle control signal to the OCV. This control signal regulates the oil pressure supplied to the camshaft timing exhaust gear assembly. The camshaft timing exhaust gear assembly can advance or retard the exhaust camshaft.
If the difference between the target and actual exhaust valve timing is large, and changes in actual exhaust valve timing are small, the ECM interprets this as the camshaft timing exhaust gear assembly stuck malfunction and stores a DTC.

WIRING DIAGRAM

Refer to DTC P0013 (Click here).

INSPECTION PROCEDURE


HINT:
Abnormal Bank
Advanced Timing Over
(Valve Timing Out of Specified Range)
Retarded Timing Over
(Valve Timing Out of Specified Range)
Bank 1
P0014
P0015
Bank 2
P0024
P0025
  1. If DTC P0014 or P0015 is displayed, check the VVT system for exhaust side of bank 1 camshaft circuit.
  2. Bank 1 refers to the bank that includes No. 1 cylinder.
  3. If DTC P0024 or P0025 is displayed, check the VVT system for exhaust side of bank 2 camshaft circuit.
  4. Bank 2 refers to the bank that does not include No. 1 cylinder.
  5. Read freeze frame data using the intelligent tester. Freeze frame data record the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air-fuel ratio was lean or rich, and other data, from the time the malfunction occurred.


1. CHECK ANY OTHER DTCS OUTPUT (IN ADDITION TO DTC P0014, P0015, P0024 OR P0025)
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the tester on.

  1. Enter the following menus: Powertrain / Engine and ECT / DTC.

  1. Read DTCs.

    Result 
    Result
    Proceed to
    P0014, P0015, P0024 or P0025 is output
    A
    P0014, P0015, P0024 or P0025 and other DTCs are output
    B

    HINT:
    If any DTCs other than P0014, P0015, P0024 or P0025 are output, troubleshoot those DTCs first.



B
GO TO DTC CHART (Click here)
A


2. PERFORM ACTIVE TEST USING INTELLIGENT TESTER (OPERATE OCV)
  1. Connect the intelligent tester to the DLC3.

  1. Start the engine.

  1. Turn the tester on.

  1. Warm up the engine.

  1. Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the VVT Exhaust Linear (Bank1) or Control the VVT Exhaust Linear (Bank2).

  1. Check the engine speed while operating the Camshaft Timing Oil Control Valve (OCV) assembly using the tester.

    OK:
    Tester Operation
    Specified Condition
    0%
    Normal engine speed
    100%
    Engine idles roughly or stalls



NG
Go to step 4
OK


3. CHECK WHETHER DTC OUTPUT RECURS (DTC P0014, P0015, P0024 OR P0025)
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the tester on.

  1. Clear DTCs (Click here).

  1. Start the engine and warm up the engine.

  1. Switch the ECM from normal mode to check mode using the tester (Click here).

  1. Allow the engine to idle for 3 minutes or more.

  1. Drive the vehicle for more than 10 minutes.

  1. Read DTCs using the tester.

    OK:
    No DTC output.



NG
Go to step 4
OK

CHECK FOR INTERMITTENT PROBLEMS (Click here)

4. CHECK VALVE TIMING (CHECK FOR LOOSE AND JUMPED TEETH ON TIMING CHAIN)
A135015E06
  1. Remove the cylinder head cover LH and RH.

  1. Turn the crankshaft pulley, and align its groove with the alignment mark "0" of the timing chain cover.

  1. Check that the alignment marks of the camshaft timing gears and camshaft timing exhaust gears are at the positions shown in the illustration.

    Text in Illustration:
    *1
    Alignment Mark

    OK:
    Alignment marks on camshaft timing gears are aligned as shown in the illustration.



NG
ADJUST VALVE TIMING (Click here)
OK


5. INSPECT CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY (OCV FOR EXHAUST CAMSHAFT)
  1. Inspect the camshaft timing oil control valve assembly (Click here).



NG
REPLACE CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY (Click here)
OK


6. INSPECT OIL CONTROL VALVE FILTER
  1. Remove the oil control valve filter (Click here).

  1. Check that the filter is not clogged.

    OK:
    Filter is not clogged.



NG
CLEAN OIL CONTROL VALVE FILTER
OK


7. INSPECT CAMSHAFT TIMING EXHAUST GEAR ASSEMBLY
  1. Inspect the camshaft timing exhaust gear assembly. (Click here).



NG
REPLACE CAMSHAFT TIMING EXHAUST GEAR ASSEMBLY (Click here)
OK


8. CHECK WHETHER DTC OUTPUT RECURS
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the tester on.

  1. Clear DTCs (Click here).

  1. Warm up the engine.

  1. Switch the ECM from normal mode to check mode using the tester (Click here).

  1. Allow the engine to idle for 3 minutes or more.

  1. Drive the vehicle for more than 10 minutes.

  1. Read DTCs using the tester.

    OK:
    No DTC output.

HINT:
DTC P0014, P0015, P0024 or P0025 is output when foreign objects in the engine oil are caught in some parts of the system. These codes will stay registered even if the system returns to normal after a short time. These foreign objects are then captured by the oil filter, thus eliminating the source of the problem.



NG
REPLACE ECM (Click here)
OK

END


← P0014 Camshaft Position "B" - Timing Over-Advanced or System Performance (Bank 1) (+ P0015, P0024, P0025) (Nov 2010 – Jul 2014)P0016 Crankshaft Position - Camshaft Position Correlation (Bank 1 Sensor A) (+ P0018) (Jul 2007 – Jul 2009) →