2011-2016 FJ Cruiser · Service Manual BRAKE

C1422 Master Cylinder Pressure Sensor Zero Point High Malfunction

Diagnostic trouble codes · Vehicles built from Aug 2014

Versions by build date: Nov 2010 – Jul 2012 Aug 2012 – Jul 2014 from Aug 2014

DESCRIPTION

Refer to DTCs C1421, C1423 and C1424 (Click here).
DTC Code
DTC Detection Condition
Trouble Area
C1422
When the stop light switch is off, the PM/C1 terminal voltage is 0.86 V or higher for 5 seconds or more.
  1. Stop light switch
  2. Stop light switch circuit
  3. Master cylinder pressure sensor circuit
  4. Master cylinder solenoid (Master cylinder pressure sensor)

WIRING DIAGRAM

Refer to DTC C1380 (Click here).

INSPECTION PROCEDURE

NOTICE:
When replacing the master cylinder solenoid, perform calibration (Click here).

HINT:
When DTC C1425 is output together with DTC C1422, inspect and repair the trouble areas indicated by DTC C1425 first (Click here).


1. CHECK STOP LIGHT OPERATION
  1. Check that the stop lights come on when the brake pedal is depressed and go off when the brake pedal is released.

    OK:
    Stop light switch function is normal.



NG
GO TO LIGHTING SYSTEM (PROBLEM SYMPTOMS TABLE) (Click here)
OK


2. READ VALUE USING INTELLIGENT TESTER (STOP LIGHT SW)
  1. Turn the ignition switch off.

  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the tester on.

  1. Enter the following menus: Chassis / ABS/VSC/TRC / Data List.

    ABS/VSC/TRC 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    Stop Light SW
    Stop light switch/ ON or OFF
    ON: Brake pedal depressed
    OFF: Brake pedal released
    -

  1. Check that the stop light condition observed on the tester changes according to brake pedal operation.

    OK:
    The tester displays ON or OFF according to brake pedal operation.



NG
Go to step 5
OK


3. CHECK BRAKE PEDAL AND STOP LIGHT SWITCH INSTALLATION
  1. Turn the ignition switch off.

  1. Check the brake pedal height and stop light switch installation (Click here).

    OK:
    The brake pedal height and stop light switch installation are normal.



NG
ADJUST BRAKE PEDAL OR STOP LIGHT SWITCH (Click here)
OK


4. RECONFIRM DTC
  1. Clear the DTCs (Click here).

  1. Start the engine.

  1. Drive the vehicle at a speed of 40 km/h (25 mph) or more and perform a braking test (decelerate the vehicle by depressing the brake pedal).

  1. Check if the same DTC is output (Click here).

    Result 
    Result
    Proceed to
    DTC C1422 is not output
    A
    DTC C1422 is output
    B



B
REPLACE MASTER CYLINDER SOLENOID (Click here)
A

USE SIMULATION METHOD TO CHECK (Click here)

5. INSPECT SKID CONTROL ECU (STP TERMINAL)
  1. Disconnect the skid control ECU connector.

  1. C213546E18
    Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    A4-7 (STP) - Body ground
    Brake pedal depressed
    8 to 14 V
    A4-7 (STP) - Body ground
    Brake pedal released
    Below 1.5 V

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Skid Control ECU)



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE MASTER CYLINDER SOLENOID (Click here)


← C1422 Master Cylinder Pressure Sensor Zero Point High Malfunction (Aug 2012 – Jul 2014)C1425 Open in Stop Light Switch Circuit (Nov 2010 – Jul 2012) →