P2445 Secondary Air Injection System Pump Stuck Off Bank1
Diagnostic trouble codes · Vehicles built from Aug 2014
DESCRIPTION
Refer to P0412 (Click here).| DTC No. |
DTC Detection Condition |
Trouble Area |
| P2445 |
Both of the following conditions are met for 7 seconds (2 trip detection logic): (a) Engine is running (b) Secondary air injection pressure is less than 1 kPa (7.5 mmHg) when secondary air injection is ON |
|
MONITOR DESCRIPTION
The ECM monitors the pressure in the secondary air passage using the pressure sensor located on the emission control valve set of the secondary air injection system. The sensor measures the pressure in the secondary air passage and transmits a signal to the ECM.If either of the following conditions occurs, the ECM interprets it as a malfunction of the secondary air injection system, and illuminates the MIL and stores a DTC:
- The pressure indicated by the pressure sensor does not reach threshold levels despite the ECM turning on the air pump assembly.
- The pressure indicated by the pressure sensor exceeds threshold levels despite the ECM turning off the air pump assembly.
- DTC P2445 mainly indicate a malfunction in which the air pump assembly is stuck off.
CONFIRMATION DRIVING PATTERN
- NOTICE:
- This Secondary Air Injection Check only allows technicians to operate the secondary air injection system for a maximum of 5 seconds. Furthermore, the check can only be performed up to 4 times per trip. If the test is repeated, intervals of at least 30 seconds are required between checks. While secondary air injection system operation using the intelligent tester is prohibited, the intelligent tester display indicates the prohibition (WAIT or ERROR). If ERROR is displayed on the intelligent tester during the test, stop the engine for 10 minutes, and then try again.
- Performing Secondary Air Injection Check repeatedly may cause damage to the secondary air injection system. If it is necessary to repeat the check, leave an interval of several minutes between System Check operations to prevent the system from overheating.
- When performing the Secondary Air Injection Check operation after the battery cable has been reconnected, wait for 7 minutes with the ignition switch turned to ON or the engine running.
- Turn the ignition switch off when the Secondary Air Injection Check operation finishes.
- This Secondary Air Injection Check only allows technicians to operate the secondary air injection system for a maximum of 5 seconds. Furthermore, the check can only be performed up to 4 times per trip. If the test is repeated, intervals of at least 30 seconds are required between checks. While secondary air injection system operation using the intelligent tester is prohibited, the intelligent tester display indicates the prohibition (WAIT or ERROR). If ERROR is displayed on the intelligent tester during the test, stop the engine for 10 minutes, and then try again.
- Start the engine and warm it up.
- Turn the ignition switch off.
- Connect the intelligent tester to the DLC3.
- Turn the ignition switch to ON.
- Turn the tester on.
- Clear the DTCs (even if no DTCs are stored, perform the clear DTC operation).
- Turn the ignition switch off and wait for at least 30 seconds.
- Turn the ignition switch to ON and turn the tester on.
- Enter the following menus: Powertrain / Engine and ECT / Utility / Secondary Air Injection Check / Automatic Mode.
- Start the engine after the tester initialization is finished.
- Perform the System Check operation by pressing Next.
- Perform the following to confirm the secondary air injection system pending DTCs: Press the Exit.
- Enter the following menus: Powertrain / Engine and ECT / DTC.
- Read pending DTCs.
- HINT:
- If a pending DTC is output, the system is malfunctioning.
- If a pending DTC is not output, perform the following procedure.
- If a pending DTC is output, the system is malfunctioning.
- After Secondary Air Injection Check is completed, check All Readiness by entering the following menus: Powertrain / Engine and ECT / Utility / All Readiness.
- Input the DTC: P2445.
- Check the DTC judgment result.
Tester Display
Description
NORMAL
- DTC judgment completed
- System normal
ABNORMAL
- DTC judgment completed
- System abnormal
INCOMPLETE
- DTC judgment not completed
- Perform driving pattern after confirming DTC enabling conditions
N/A
- Unable to perform DTC judgment
- Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit
- HINT:
- If the judgment result shows NORMAL, the system is normal.
- If the judgment result shows ABNORMAL, the system has a malfunction.
- If the judgment result shows INCOMPLETE or N/A, perform the Confirmation Driving Pattern and the DTC judgment result again.
- If the judgment result shows NORMAL, the system is normal.
- DTC judgment completed
WIRING DIAGRAM
Refer to DTC P0412 (Click here).INSPECTION PROCEDURE
- HINT:
- Determination by ECM monitoring:
- The ECM detects malfunctions in the secondary air injection system by detecting the pressure in the secondary air injection passage between the air pump assembly and emission control valve set and stores a DTC. Soon after a cold engine start, the monitor runs for a short time while the secondary air injection system is both ON and OFF. The ECM detects both the pressure and the exhaust pulsation and compares them.
- The following 8 patterns are secondary air injection system pressure conditions in the secondary air injection system passage.
| Air Pump Assembly |
ON |
| Emission Control Valve Set |
Open |
| Pressure |
1 kPa (7.5 mmHg) or higher |
| Pulsation Detection |
Exhaust gas pulsation detected |
| Air Pump Assembly |
OFF |
| Emission Control Valve Set |
Open |
| Pressure |
Below 2.5 kPa (18.7 mmHg) |
| Pulsation Detection |
Exhaust gas pulsation detected |
| Air Pump Assembly |
ON |
| Emission Control Valve Set |
Closed |
| Pressure |
1 kPa (7.5 mmHg) or higher |
| Pulsation Detection |
Exhaust gas pulsation not detected |
| Air Pump Assembly |
OFF |
| Emission Control Valve Set |
Closed |
| Pressure |
Below 2.5 kPa (18.7 mmHg) |
| Pulsation Detection |
Exhaust gas pulsation not detected |
| Air Pump Assembly |
ON |
| Emission Control Valve Set |
Open |
| Pressure |
1 kPa (7.5 mmHg) or higher |
| Pulsation Detection |
Exhaust gas pulsation detected |
| Air Pump Assembly |
OFF |
| Emission Control Valve Set |
Open |
| Pressure |
Below 2.5 kPa (18.7 mmHg) |
| Pulsation Detection |
Exhaust gas pulsation detected |
| Air Pump Assembly |
ON |
| Emission Control Valve Set |
Closed |
| Pressure |
1 kPa (7.5 mmHg) or higher |
| Pulsation Detection |
Exhaust gas pulsation not detected |
| Air Pump Assembly |
OFF |
| Emission Control Valve Set |
Closed |
| Pressure |
Below 2.5 kPa (18.7 mmHg) |
| Pulsation Detection |
Exhaust gas pulsation not detected |
- HINT:
- The exhaust pulsation value is calculated in the ECM. If the calculated value exceeds a certain level, the ECM determines that the exhaust pulsation is in the secondary air injection system.
- HINT:
- In cases 3 and 7, as the pressure sensor detects a slight pump operation pulsation, the detected value is not constant. Since the pump outlet is blocked by closing the emission control valve, the average pressure is higher than in case 1 (approximately 15 to 25 kPa (112.5 to 187.5 mmHg)).
- In case 1, the average pressure is approximately 3 to 11 kPa (22.5 to 82.5 mmHg)). The value of 1 kPa indicated in the table above is a threshold for detecting pump malfunctions.
- In cases 3 and 7, as the pressure sensor detects a slight pump operation pulsation, the detected value is not constant. Since the pump outlet is blocked by closing the emission control valve, the average pressure is higher than in case 1 (approximately 15 to 25 kPa (112.5 to 187.5 mmHg)).
| Detected Condition while Secondary Air Injection Operating: Air Pump Assembly ON, Emission Control Valve Set Open |
Detected Condition while Secondary Air Injection not Operating: Air Pump Assembly OFF, Emission Control Valve Set Closed |
ECM Determination |
DTC Output |
| Case 1 |
Case 8 |
Normal or emission control valve set stuck open |
- or P2441 or P2443 |
| Case 1 |
Case 6 |
Emission control valve set stuck open |
P2440 and P2442 or P2442 (only) |
| Case 1 |
Case 7 |
Normal |
- |
| Case 2 |
Case 8 |
Air pump assembly stuck OFF |
P2445 |
| Case 3 |
Case 8 |
Normal |
- |
| Case 1 |
Case 5 |
Normal |
- |
| Case 2 |
Case 6 |
Emission control valve set stuck open and air pump assembly stuck OFF |
P2440 and/or P2442 and P2445 |
| Case 3 |
Case 7 |
Normal |
- |
| Case 4 |
Case 8 |
Normal |
- |
- HINT:
- By using the intelligent tester to perform the Secondary Air Injection Check operation in the System Check, the air fuel ratio and the pressure in the secondary air injection system passage can be checked while the secondary air injection system is operating. This helps technicians to troubleshoot the system when it malfunctions. Furthermore, pending codes also can be checked by performing Utility / Secondary Air Injection Check / Automatic Mode after the repair.
- Read freeze frame data using the intelligent tester. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.
- By using the intelligent tester to perform the Secondary Air Injection Check operation in the System Check, the air fuel ratio and the pressure in the secondary air injection system passage can be checked while the secondary air injection system is operating. This helps technicians to troubleshoot the system when it malfunctions. Furthermore, pending codes also can be checked by performing Utility / Secondary Air Injection Check / Automatic Mode after the repair.
- System Check:
- NOTICE:
- This Secondary Air Injection Check only allows technicians to operate the secondary air injection system for a maximum of 5 seconds. Furthermore, the check can only be performed up to 4 times per trip. If the test is repeated, intervals of at least 30 seconds are required between checks. While secondary air injection system operation using the intelligent tester is prohibited, the intelligent tester display indicates the prohibition (WAIT or ERROR). If ERROR is displayed on the intelligent tester during the test, stop the engine for 10 minutes, and then try again.
- Performing Secondary Air Injection Check repeatedly may cause damage to the secondary air injection system. If it is necessary to repeat the check, leave an interval of several minutes between System Check operations to prevent the system from overheating.
- When performing the Secondary Air Injection Check operation after the battery cable has been reconnected, wait for 7 minutes with the ignition switch turned to ON or the engine running.
- Turn the ignition switch off when the Secondary Air Injection Check operation finishes.
- This Secondary Air Injection Check only allows technicians to operate the secondary air injection system for a maximum of 5 seconds. Furthermore, the check can only be performed up to 4 times per trip. If the test is repeated, intervals of at least 30 seconds are required between checks. While secondary air injection system operation using the intelligent tester is prohibited, the intelligent tester display indicates the prohibition (WAIT or ERROR). If ERROR is displayed on the intelligent tester during the test, stop the engine for 10 minutes, and then try again.
- The pressure in the secondary air passage can be checked using the intelligent tester.
- Start the engine and warm it up.
- Turn the ignition switch off.
- Connect the intelligent tester to the DLC3.
- Turn the ignition switch to ON.
- Turn the tester on.
- Enter the following menus: Powertrain / Engine and ECT / Utility / Secondary Air Injection Check / Manual Mode / AIR PUMP: ON, ASV1: OPEN, ASV2: OPEN and AIR PUMP: OFF, ASV1 CLOSE, ASV2 CLOSE.
- HINT:
- When Manual Mode is selected, the tester initialization (atmospheric pressure measurement) is performed automatically. The initialization takes 10 seconds. After the initialization, AIR PUMP and ASV operation can be selected.
- Start the engine.
- Perform the secondary air injection system forced operation while the engine is idling.
- Check that the Data List values for the air pump (AIR PUMP), emission control valve (ASV) and pressure in the secondary air injection system passage (PRESSURE) displayed on the tester are as shown in the table below.
- Standard:
Tester Operation
Air Pump Assembly
Emission Control Valve Set
Pressure*1
Pulsation*2
AIR PUMP: ON, ASV: OPEN
ON
OPEN
1 kPa (7.5 mmHg) or higher
1.25 kPa (9.3 mmHg) or higher
AIR PUMP: OFF, ASV: CLOSE
OFF
CLOSE
Below 2.5 kPa (18.7 mmHg)
Below 10 kPa (7.5 mmHg)
*2: The cumulative exhaust pulsation calculated by the ECM. If the calculated value exceeds a certain level, the ECM determines that the exhaust pulsation is in the secondary air injection system.
- Turn the ignition switch off.
- NOTICE:
- Inspect the fuses for circuits related to this system before performing the following inspection procedure.
- HINT:
- Bank 1 refers to the bank that includes the No. 1 cylinder*.
*: The No. 1 cylinder is the cylinder which is farthest from the transmission.
- Bank 2 refers to the bank that does not include the No. 1 cylinder.
- Bank 1 refers to the bank that includes the No. 1 cylinder*.
| 1. CHECK FOR ANY OTHER DTCS OUTPUT (IN ADDITION TO DTC P2445) |
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON.
Turn the tester on.
Enter the following menus: Powertrain / Engine and ECT / DTC.
Read the DTCs.
Result Result
Proceed to
P2445 is output
A
P2445 and P0418 are output
B
P2445 and other DTCs (except P0418) are output
C
- HINT:
- If any DTCs other than P0418 and P2445 are output, troubleshoot those DTCs first.
|
|
||||
|
|
||||
| A | |
| 2. CHECK FREEZE FRAME DATA (AIR PUMP FREEZE, AIR SWITCHING VALVE FREEZE AND AIR SWITCHING VALVE2 FREEZE) |
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON and turn the tester on.
Read the values of Air Pump Freeze, Air Switching Valve Freeze and Air Switching Valve2 Freeze from the freeze frame data recorded previously.
Referring to the following table, proceed to the appropriate step according to the result of the data reading.
Result Result
Proceed to
Air Pump Freeze
Air Switching Valve Freeze
Air Switching Valve2 Freeze
OFF
OFF
OFF
B
Except above
A
|
|
||||
| A | |
| 3. PERFORM ACTIVE TEST USING INTELLIGENT TESTER (ACTIVE THE AIR PUMP HEATER) |
Disconnect the air pump assembly connector.

Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON and turn the tester on.
Enter the following menus: Powertrain / Engine and ECT/ Active Test / Activate the Air Pump Heater.
Measure the voltage according to the value(s) in the table below.
- Standard Voltage:
Tester Connection
Condition
Specified Condition
A44-1 (APH+) - Body ground
Activate the Air Pump Heater is ON
11 to 14 V
Text in Illustration *a
Front view of wire harness connector
(to Air Pump Assembly)
|
|
||||
| OK | |
| 4. INSPECT AIR PUMP ASSEMBLY (HEATER RESISTANCE) |
Inspect the air pump assembly (Click here).
|
|
||||
| OK | |
| 5. INSPECT AIR PMP HTR RELAY |
Inspect the AIR PMP HTR relay (Click here).
|
|
||||
| OK | |
| 6. CHECK TERMINAL VOLTAGE (POWER SOURCE OF AIR PMP HTR RELAY) |
Remove the AIR PMP HTR relay from the engine room relay block.
Measure the voltage according to the value(s) in the table below.

- Standard Voltage:
Tester Connection
Condition
Specified Condition
5 (AIR PMP HTR relay holder) - Body ground
Always
11 to 14 V
Text in Illustration *1
Engine Room Relay Block
*2
AIR PMP HTR Relay Holder
|
|
||||
| OK | |
| 7. CHECK HARNESS AND CONNECTOR (AIR PUMP ASSEMBLY - AIR PMP HTR RELAY, BODY GROUND) |
Remove the AIR PMP HTR relay from the engine room relay block.
Disconnect the A44 air pump assembly connector.
Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection
Condition
Specified Condition
3 (AIR PMP HTR relay holder) - A44-1 (APH+)
Always
Below 1 Ω
A44-3 (APHG) - Body ground
Always
Below 1 Ω
3 (AIR PMP HTR relay holder) or A44-1 (APH+) - Body ground
Always
10 kΩ or higher
|
|
||||
| OK | |
| 8. PERFORM ACTIVE TEST USING INTELLIGENT TESTER (SECONDARY AIR INJECTION SYSTEM OPERATION) |
Start the engine and warm it up.
Turn the ignition switch off.
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON.
Turn the tester on.
Enter the following menus: Powertrain / Engine and ECT / Utility / Secondary Air Injection Check / Manual Mode / AIR PUMP: ON, ASV1: OPEN, ASV2: OPEN and AIR PUMP: OFF, ASV1: CLOSE, ASV2: CLOSE.
- HINT:
- When Manual Mode is selected, the tester initialization (atmospheric pressure measurement) is performed automatically. The initialization takes 10 seconds. After the initialization, AIR PUMP and ASV operation can be selected.
Start the engine.
Perform the secondary air injection system forced operation while the engine is idling.
Check that the Data List values for the air pump (AIR PUMP), emission control valve (ASV) and pressure in the secondary air injection system passage (PRESSURE) displayed on the tester are as shown in the table below.
- Standard:
Tester Operation
Air Pump
Emission Control Valve
PRESSURE*
AIR PUMP: ON, ASV: OPEN
ON
ON
1 kPa (7.5 mmHg) or higher [A]
AIR PUMP: OFF, ASV: CLOSE
OFF
OFF
Below 2.5 kPa (18.7 mmHg) [B]
- Standard:
- The pressures for [A] and [B] should differ by 1 kPa (7.5 mmHg) or more.
Turn the ignition switch off.
- NOTICE:
- This Secondary Air Injection Check only allows technicians to operate the secondary air injection system for a maximum of 5 seconds. Furthermore, the check can only be performed up to 4 times per trip. If the test is repeated, intervals of at least 30 seconds are required between checks. While secondary air injection system operation using the intelligent tester is prohibited, the intelligent tester display indicates the prohibition (WAIT or ERROR). If ERROR is displayed on the intelligent tester during the test, stop the engine for 10 minutes, and then try again.
- Performing Secondary Air Injection Check repeatedly may cause damage to the secondary air injection system. If it is necessary to repeat the check, leave an interval of several minutes between System Check operations to prevent the system from overheating.
- When performing the Secondary Air Injection Check operation after the battery cable has been reconnected, wait for 7 minutes with the ignition switch turned to ON or the engine running.
- Turn the ignition switch off when the Secondary Air Injection Check operation finishes.
- This Secondary Air Injection Check only allows technicians to operate the secondary air injection system for a maximum of 5 seconds. Furthermore, the check can only be performed up to 4 times per trip. If the test is repeated, intervals of at least 30 seconds are required between checks. While secondary air injection system operation using the intelligent tester is prohibited, the intelligent tester display indicates the prohibition (WAIT or ERROR). If ERROR is displayed on the intelligent tester during the test, stop the engine for 10 minutes, and then try again.
|
|
||||
| OK | |
| 9. CHECK WHETHER DTC OUTPUT RECURS (DTC P2445) |
Start the engine and warm it up.
Turn the ignition switch off.
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON.
Turn the tester on.
Clear the DTCs (if stored) (Click here).
Enter the following menus: Powertrain / Engine and ECT / Utility / Secondary Air Injection Check / Automatic Mode.
Start the engine after the tester initialization is finished.
Perform the System Check operation by pressing Next.
Perform the following to confirm the secondary air injection system pending DTCs: Press the Exit.
Enter the following menus: Powertrain / Engine and ECT / DTC.
Read pending DTCs.
Turn the ignition switch off.
- NOTICE:
- When performing the Secondary Air Injection Check operation after the battery cable has been reconnected, wait for 7 minutes with the ignition switch turned to ON or the engine running.
- Turn the ignition switch off when the Secondary Air Injection Check operation finishes.
- When performing the Secondary Air Injection Check operation after the battery cable has been reconnected, wait for 7 minutes with the ignition switch turned to ON or the engine running.
Result Result
Proceed to
P2445 is output
A
No pending DTC is output
B
|
|
||||
| A | |
| 10. INSPECT EMISSION CONTROL VALVE SET (PRESSURE SENSOR) |
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON.
Turn the tester on.
Enter the following menus: Powertrain / Engine and ECT / Data List / Air Pump Pressure (Absolute) and Air Pump2 Pressure (Absolute).
Check the pressure displayed on the tester.
- Standard pressure:
- 45.63 to 135 kPa (342 to 1013 mmHg)
- HINT:
- The tester displays the air pump pressure as absolute pressure.
Result Result
Proceed to
OK
A
NG (for Bank 1)
B
NG (for Bank 2)
C
|
|
||||
|
|
||||
| A | |
| 11. CHECK SECONDARY AIR INJECTION SYSTEM PIPE CONNECTIONS |


Check that all the pipes and hoses between the air pump and emission control valve are securely connected.
Inspect the pipes and hoses for blockages and damage.
- OK:
- Secondary air injection system piping has no blockages or damage.
|
|
||||
| OK | |
| 12. INSPECT AIR INJECTION CONTROL DRIVER (AIR INJECTION CONTROL DRIVER POWER SOURCE CIRCUIT) |
![]() ![]() |
Disconnect the air injection control driver connectors.
Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection
Condition
Specified Condition
A45-1 (E) - Body ground
Always
Below 1 Ω
Turn the ignition switch to ON.
Measure the voltage according to the value(s) in the table below.
- Standard Voltage:
Tester Connection
Switch Condition
Specified Condition
A46-1 (BATT) - Body ground
Always
11 to 14 V (near battery voltage)
A45-5 (+B) - Body ground
Ignition switch ON
11 to 14 V (near battery voltage)
| *a |
Front view of wire harness connector (to Air Injection Control Driver) |
|
|
||||
| OK | |
| 13. CHECK HARNESS AND CONNECTOR (ECM - AIR INJECTION CONTROL DRIVER) |
Disconnect the B48 ECM connector.
Disconnect the A45 air injection control driver connector.
Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection
Condition
Specified Condition
B48-23 (AIRP) - A45-4 (SIP)
Always
Below 1 Ω
B48-23 (AIRP) or A45-4 (SIP) - Body ground
Always
10 kΩ or higher
|
|
||||
| OK | |
| 14. CHECK AIR PUMP ASSEMBLY |
Inspect the air pump assembly (Click here).
|
|
||||
|
|
||||
| 15. REPLACE AIR PUMP ASSEMBLY |
Replace the air pump assembly (Click here).
| NEXT | |
| 16. CHECK WHETHER DTC OUTPUT RECURS (DTC P2445) |
Start the engine and warm it up.
Turn the ignition switch off.
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON.
Turn the tester on.
Clear the DTCs (if stored) (Click here).
Enter the following menus: Powertrain / Engine and ECT / Utility / Secondary Air Injection Check / Automatic Mode.
Start the engine after the tester initialization is finished.
Perform the System Check operation by pressing Next.
Perform the following to confirm the secondary air injection system pending DTCs: Press the Exit.
Enter the following menus: Powertrain / Engine and ECT / DTC.
Read pending DTCs.
- OK:
- No pending DTC is output.
Turn the ignition switch off.
- NOTICE:
- When performing the Secondary Air Injection Check operation after the battery cable has been reconnected, wait for 7 minutes with the ignition switch turned to ON or the engine running.
- Turn the ignition switch off when the Secondary Air Injection Check operation finishes.
- When performing the Secondary Air Injection Check operation after the battery cable has been reconnected, wait for 7 minutes with the ignition switch turned to ON or the engine running.
|
|
||||
| OK | ||
| ||
| 17. PERFORM ACTIVE TEST USING INTELLIGENT TESTER |
Disconnect the air injection control driver connector.

Connect terminals DI and SIV of the wire harness connector for the air injection control driver.
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON and turn the tester on.
Enter the following menus: Powertrain / Engine and ECT / Utility / Secondary Air Injection Check / Manual Mode / AIR PUMP: ON, ASV 1: OPEN, ASV 2: OPEN.
- HINT:
- When Manual Mode is selected, the tester initialization (atmospheric pressure measurement) is performed automatically. The initialization takes 10 seconds. After the initialization, AIR PUMP and ASV operation can be selected.
Start the engine.
Perform the secondary air injection system forced operation while the engine is idling.
Measure the voltage between the SIV and E terminals of the ECM connector when the secondary air injection system is ON and OFF.
Turn the ignition switch off.
- NOTICE:
- Performing Secondary Air Injection Check repeatedly may cause damage to the secondary air injection system. If it is necessary to repeat the check, leave an interval of several minutes between System Check operations to prevent the system from overheating.
- When performing the Secondary Air Injection Check operation after the battery cable has been reconnected, wait for 7 minutes with the ignition switch turned to ON or the engine running.
- Turn the ignition switch off when the Secondary Air Injection Check operation finishes.
- Performing Secondary Air Injection Check repeatedly may cause damage to the secondary air injection system. If it is necessary to repeat the check, leave an interval of several minutes between System Check operations to prevent the system from overheating.
- Standard Voltage:
Tester Connection
Condition
Specified Condition
A45-3 (SIV) - A45-1 (E)
AIR PUMP: ON, ASV: OPEN
0.5 to 2 V
A45-3 (SIV) - A45-1 (E)
AIR PUMP: OFF, ASV: CLOSE
11 to 14 V
Text in Illustration *1
Air Injection Control Driver
*2
ECM
*a
Front view of wire harness connector
(to Air Injection Control Driver)
Connect terminals DI and SIP of the wire harness connector for the air injection control driver.

Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON and turn the tester on.
Enter the following menus: Powertrain / Engine and ECT / Utility / Secondary Air Injection Check / Manual Mode / AIR PUMP: ON, ASV 1: OPEN, ASV 2: OPEN.
- HINT:
- When Manual Mode is selected, the tester initialization (atmospheric pressure measurement) is performed automatically. The initialization takes 10 seconds. After the initialization, AIR PUMP and ASV operation can be selected.
Start the engine.
Perform the secondary air injection system forced operation while the engine is idling.
Measure the voltage between the SIP and E terminals of the ECM connector when the secondary air injection system is ON and OFF.
Turn the ignition switch off.
- NOTICE:
- Performing Secondary Air Injection Check repeatedly may cause damage to the secondary air injection system. If it is necessary to repeat the check, leave an interval of several minutes between System Check operations to prevent the system from overheating.
- When performing the Secondary Air Injection Check operation after the battery cable has been reconnected, wait for 7 minutes with the ignition switch turned to ON or the engine running.
- Turn the ignition switch off when the Secondary Air Injection Check operation finishes.
- Performing Secondary Air Injection Check repeatedly may cause damage to the secondary air injection system. If it is necessary to repeat the check, leave an interval of several minutes between System Check operations to prevent the system from overheating.
- Standard Voltage:
Tester Connection
Condition
Specified Condition
A45-4 (SIP) - A45-1 (E)
AIR PUMP: ON, ASV: OPEN
0.5 to 2 V
A45-4 (SIP) - A45-1 (E)
AIR PUMP: OFF, ASV: CLOSE
11 to 14 V
Text in Illustration *1
Air Injection Control Driver
*2
ECM
*a
Front view of wire harness connector
(to Air Injection Control Driver)
|
|
||||
| OK | |
| 18. REPLACE AIR INJECTION CONTROL DRIVER |
Replace the air injection control driver (Click here).
| NEXT | |
| 19. CHECK WHETHER DTC OUTPUT RECURS (DTC P2445) |
Start the engine and warm it up.
Turn the ignition switch off.
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON.
Turn the tester on.
Clear the DTCs (if stored) (Click here).
Enter the following menus: Powertrain / Engine and ECT / Utility / Secondary Air Injection Check / Automatic Mode.
Start the engine after the tester initialization is finished.
Perform the System Check operation by pressing Next.
Perform the following to confirm the secondary air injection system pending DTCs: Press the Exit.
Enter the following menus: Powertrain / Engine and ECT / DTC.
Read pending DTCs.
- OK:
- No pending DTC is output.
Turn the ignition switch off.
- NOTICE:
- When performing the Secondary Air Injection Check operation after the battery cable has been reconnected, wait for 7 minutes with the ignition switch turned to ON or the engine running.
- Turn the ignition switch off when the Secondary Air Injection Check operation finishes.
- When performing the Secondary Air Injection Check operation after the battery cable has been reconnected, wait for 7 minutes with the ignition switch turned to ON or the engine running.
|
|
||||
| OK | ||
| ||

