2011-2016 FJ Cruiser · Service Manual BRAKE

TEST MODE PROCEDURE

Troubleshooting · Vehicles built Aug 2008 – Oct 2010

Versions by build date: Jul 2007 – Jul 2008 Aug 2008 – Oct 2010 from Nov 2010


TEST MODE PROCEDURE (for Using an Intelligent Tester)

HINT:
  1. After replacing the yaw rate and deceleration sensor, be sure to clear the zero point calibration data in the skid control ECU and perform zero point calibration.
  2. If the ignition switch is turned from ON to ACC or LOCK position during test mode, DTCs related to the signal check function will be erased.
  3. During test mode, the skid control ECU records all DTCs related to the signal check function. By performing the signal check, the codes are erased if normality is confirmed. The codes left over are the codes where an abnormality was found.

  1. Turn the ignition switch off.

  2. Check that the steering wheel is in the straight-ahead position.

  3. Automatic Transmission: Check that the shift lever is in the P position and apply the parking brake.
    Manual Transmission: Check that the shift lever is in neutral and apply the parking brake.

  4. Connect the intelligent tester to the DLC3.

  5. Start the engine.

  6. Switch the ECU to test mode using the intelligent tester. Select the following menu items: Chassis / ABS/VSC/TRC / Signal Check

  7. BR03904E96
    w/o VSC OFF Switch:
    Check that the ABS and VSC TRC warning lights blink as shown in the illustration.
    w/ VSC OFF Switch:
    Check that the ABS warning light and SLIP indicator light blink as shown in the illustration.

    HINT:
    If the ABS warning light and VSC TRC warning light (*1) or SLIP indicator light (*2) do not blink, inspect the ABS warning light circuit and VSC TRC warning light circuit (*1) or SLIP indicator light circuit (*2).
    Trouble area
    See page
    ABS warning light circuit
    Click here
    Click here
    VSC TRC warning light circuit (*1)
    Click here
    Click here
    SLIP indicator light circuit (*2)
    Click here
    Click here
    *1: w/o VSC OFF Switch
    *2: w/ VSC OFF Switch

  8. Activate the ABS sensors (deceleration sensor, master cylinder pressure sensor, 4WD detection switch, L4 detection switch and speed sensor) and VSC sensor (yaw rate and deceleration sensor) in test mode (SIGNAL CHECK) using an intelligent tester.


TEST MODE PROCEDURE (for Using SST Check Wire)

HINT:
  1. After replacing the yaw rate and deceleration sensor, be sure to clear the zero point calibration data in the skid control ECU and perform zero point calibration.
  2. If the ignition switch is turned from ON to ACC or LOCK position during test mode, DTCs relating to the signal check function will be erased.
  3. During test mode, the skid control ECU records all DTCs relating to the signal check function. By performing the signal check, the codes are erased if normality is confirmed. The remaining codes are those indicating where an abnormality was found.

  1. Turn the ignition switch off.

  2. Check that the steering wheel is in the straight-ahead position.

  3. Automatic Transmission: Check that the shift lever is in the P position and apply the parking brake.
    Manual Transmission: Check that the shift lever is in neutral and apply the parking brake.

  4. F100115E85
    Using SST, connect terminals TS and CG of the DLC3.
    SST
    09843-18040  

  5. Start the engine.

  6. BR03904E96
    w/o VSC OFF Switch:
    Check that the ABS and VSC TRC warning lights blink as shown in the illustration.
    w/ VSC OFF Switch:
    Check that the ABS warning light and SLIP indicator light blink as shown in the illustration.

    HINT:
    If the ABS warning light and VSC TRC warning light (*1) or SLIP indicator light (*2) do not blink, inspect the TS and CG terminal circuit, the ABS warning light circuit and VSC TRC warning light circuit or SLIP indicator light circuit (*2).
    Trouble area
    See page
    ABS warning light circuit
    Click here
    Click here
    VSC TRC warning light circuit (*1)
    Click here
    Click here
    SLIP indicator light circuit (*2)
    Click here
    Click here
    TS and CG terminal circuit
    Click here
    *1: w/o VSC OFF Switch
    *2: w/ VSC OFF Switch

  7. Activate the ABS sensors (deceleration sensor, master cylinder pressure sensor, 4WD detection switch, L4 detection switch and speed sensor) and VSC sensor (yaw rate and deceleration sensor) in test mode (SIGNAL CHECK) using a check wire.


DECELERATION SENSOR SIGNAL CHECK
  1. Keep the vehicle stationary on a level surface for 1 second or more.

    HINT:
    The ABS warning light continues blinking at this time.


MASTER CYLINDER PRESSURE SENSOR CHECK
  1. Keep the vehicle stationary and release the brake pedal for 1 second or more, and quickly depress the brake pedal with a force of 98 N (10 kgf) or more for 1 second or more.

  2. Check that the ABS warning light comes on for 3 seconds.

    HINT:
    1. While the ABS warning light stays on, continue to depress the brake pedal with a force of 98 N (10 kgf) or more.
    2. The ABS warning light comes on for 3 seconds every time the above brake pedal operation is performed.


4WD DETECTION SWITCH SIGNAL CHECK
  1. Manual Transmission:

    1. Move the transfer high and low shift lever to HL or HH to lock the center differential.

    2. Move the transfer high and low shift lever to H to unlock the center differential.

  2. Automatic Transmission:

    1. Move the transfer high and low shift lever to H4 or L4 to put the vehicle in 4WD mode.

    2. Move the transfer high and low shift lever to H2 to put the vehicle in 2WD mode.


L4 DETECTION SWITCH SIGNAL CHECK (for Automatic Transmission)
  1. Move the transfer high and low shift lever to the L4 position.

  2. Move the transfer high and low shift lever to H4.

    HINT:
    Move the vehicle either a little forward or a little backward to engage the L4 position.


SPEED SENSOR CHECK
  1. Drive the vehicle straight rearward at a speed of 3 km/h (1.9 mph) or more for 1 second or more.

    NOTICE:
    At this time, if the vehicle speed exceeds 45 km/h (28 mph), a signal check code will be stored again. Decelerate or stop the vehicle before the speed reaches 45 km/h (28 mph).

  2. Drive the vehicle straight forward at a speed of 45 km/h (28 mph) or more.

  3. Check that the ABS warning light goes off.

    NOTICE:
    1. Before performing the speed sensor signal check, complete the deceleration sensor, master cylinder pressure sensor, 4WD detection switch and L4 detection switch signal checks.
    2. The speed sensor signal check may not be completed if the speed sensor signal check is started while turning the steering wheel or spinning the wheels.
    3. After the ABS warning light goes off, if the vehicle speed exceeds 45 km/h (28 mph), a signal check code will be stored again. Decelerate or stop the vehicle before the speed reaches 45 km/h (28 mph).
    4. If the signal check has not been completed, the ABS warning light blinks while driving and the ABS system does not operate.

    C162681E03

  4. Stop the vehicle.

    HINT:
    When the signal check has been completed, the ABS warning light goes off while driving and blinks in test mode while stationary.


READ DTC OF ABS SENSOR (for Using an Intelligent Tester)
  1. Read the DTC(s) by following the tester screen.

    HINT:
    Refer to the intelligent tester operator's manual for further details.


READ DTC OF ABS SENSOR (for Using SST Check Wire)
  1. Using SST, connect terminals TC and CG of the DLC3.

    SST
    09843-18040  

  2. Turn the ignition switch to ON.

  3. Read the number of blinks of the ABS warning light.


    1. BR03904E91
      If every sensor is normal, the normal code is displayed (A cycle of 0.25 seconds ON and 0.25 seconds OFF is repeated).

    2. If 2 or more malfunctions are detected at the same time, the lowest numbered DTC is displayed first.

      C124737E02

  4. After the check, disconnect the SST from terminals TC and CG of the DLC3.

  5. Turn the ignition switch off.


A-TRAC SWITCH CHECK (for vehicles with A-TRAC)
  1. Press the A-TRAC switch.

  2. Check that the A-TRAC indicator light comes on.

  3. Press the A-TRAC switch again to turn the A-TRAC indicator off.


YAW RATE SENSOR CHECK
  1. Keep the vehicle stationary on a level surface for 1 second or more.

  2. F002135E17
    Shift the shift lever to the D position (Automatic Transmission) and drive the vehicle at a speed of approximately 5 km/h (3 mph), turn the steering wheel either to the left or right 90° or more, and turn the vehicle through 180 degrees.

  3. Automatic Transmission: Stop the vehicle, check that the shift lever is in the P position, and then apply the parking brake.
    Manual Transmission: Stop the vehicle, check that the shift lever is in neutral, and then apply the parking brake.

  4. Check that the skid control (VSC warning) buzzer sounds for 3 seconds.

    HINT:
    1. If the skid control (VSC warning) buzzer sounds, the signal check has been completed normally.
    2. If the skid control (VSC warning) buzzer does not sound, check the skid control buzzer circuit (Click here), and then perform the signal check again.
    3. If the skid control (VSC warning) buzzer still does not sound, there is a malfunction in the yaw rate sensor, so check the DTC.
    4. Drive the vehicle in a 180° semi circle. At the end of the turn, the direction of the vehicle should be within 180+-5° of its start position.
    5. The vehicle turn should be completed within 20 seconds.
    6. Do not spin the wheels.


READ DTC OF VSC SENSOR (for Using an Intelligent Tester)
  1. Read the DTC(s) by following the tester screen.

    1. Refer to the intelligent tester operator's manual for further details.


READ DTC OF VSC SENSOR (for Using SST Check Wire)
  1. Using SST, connect terminals TC and CG of the DLC3.

    SST
    09843-18040  

  2. Turn the ignition switch to ON.

  3. w/o VSC OFF Switch:
    Read the number of blinks of the VSC TRC warning light.
    w/ VSC OFF Switch:
    Read the number of blinks of the SLIP indicator light.


    1. BR03904E91
      If every sensor is normal, the normal code is displayed (A cycle of 0.25 seconds ON and 0.25 seconds OFF is repeated).

    2. If 2 or more malfunctions are detected at the same time, the lowest numbered DTC is displayed first.

      C124737E02

  4. After the check, disconnect the SST from terminals TC and CG of the DLC3.

  5. Turn the ignition switch off.


DTC OF SIGNAL CHECK FUNCTION
ABS sensor 
DTC No.
Diagnosis
Trouble Areas
C1271/71
Low output signal of front speed sensor RH
  1. Front speed sensor RH
  2. Front speed sensor RH circuit
  3. Sensor installation
  4. Skid control sensor wire
  5. Master cylinder solenoid (skid control ECU)
C1272/72
Low output signal of front speed sensor LH
  1. Front speed sensor LH
  2. Front speed sensor LH circuit
  3. Sensor installation
  4. Skid control sensor wire
  5. Master cylinder solenoid (skid control ECU)
C1273/73
Low output signal of rear speed sensor RH
  1. Rear speed sensor RH
  2. Rear speed sensor RH circuit
  3. Sensor installation
  4. Skid control sensor wire
  5. Master cylinder solenoid (skid control ECU)
C1274/74
Low output signal of rear speed sensor LH
  1. Rear speed sensor LH
  2. Rear speed sensor LH circuit
  3. Sensor installation
  4. Skid control sensor wire
  5. Master cylinder solenoid (skid control ECU)
C1275/75
Abnormal change in output signal of front speed sensor RH
  1. Front speed sensor RH
  2. Front speed sensor RH circuit
  3. Master cylinder solenoid (skid control ECU)
C1276/76
Abnormal change in output signal of front speed sensor LH
  1. Front speed sensor LH
  2. Front speed sensor LH circuit
  3. Master cylinder solenoid (skid control ECU)
C1277/77
Abnormal change in output signal of rear speed sensor RH
  1. Rear speed sensor RH
  2. Rear speed sensor RH circuit
  3. Master cylinder solenoid (skid control ECU)
C1278/78
Abnormal change in output signal of rear speed sensor LH
  1. Rear speed sensor LH
  2. Rear speed sensor LH circuit
  3. Master cylinder solenoid (skid control ECU)
C1279/79
Deceleration sensor output voltage malfunction
  1. Yaw rate and deceleration sensor
  2. Yaw rate and deceleration sensor circuit
C1281/81
Master cylinder pressure sensor output malfunction
  1. Hydraulic brake booster (master cylinder pressure sensor)
  2. Master cylinder solenoid (skid control ECU)
  3. Stop light switch circuit
C1282/82
Center differential lock position switch malfunction
  1. Transfer indicator switch (4WD position) (Automatic transmission)
  2. Transfer indicator switch (4WD position) circuit (Automatic transmission)
  3. Transfer indicator switch (center differential lock position) (Manual transmission)
  4. Transfer indicator switch (center differential lock position) circuit (Manual transmission)
C1283/83
(*1)
L4 position switch malfunction
  1. Transfer indicator switch (L4 position)
  2. Transfer indicator switch (L4 position) circuit

HINT:
*1: Automatic transmission only

VSC sensor 
DTC No.
Diagnosis
Trouble Areas
C0371/71
Yaw rate sensor output signal malfunction
Yaw rate and deceleration sensor

HINT:
The codes in this table are output only in test mode (signal check).

← TEST MODE PROCEDURE (Jul 2007 – Jul 2008)TEST MODE PROCEDURE (from Nov 2010) →