VSC OFF Indicator Light Remains ON
Circuit diagnosis · Vehicles built Aug 2012 – Oct 2012
Versions by build date: Jul 2007 – Jul 2008 Aug 2008 – Jul 2009 Aug 2009 – Oct 2010 Nov 2010 – Jul 2011 Aug 2011 – Jul 2012 Aug 2012 – Oct 2012 from Nov 2012
DESCRIPTION
Operation of the VSC OFF switch changes the vehicle between normal mode, TRC OFF mode and VSC OFF mode. During normal mode, pressing the VSC OFF switch for a short amount of time changes vehicle to TRC OFF mode. When the vehicle is stopped, pressing the VSC OFF switch for 3 seconds or more changes the vehicle to VSC OFF mode.for 4WD:
- When the transfer is in L4 (for Automatic Transmission) or LL (for Manual Transmission), VSC is prohibited and the VSC OFF indicator and TRC OFF indicator lights turn on.
- w/ Rear Differential Lock:
When the rear differential is locked, VSC is prohibited and the VSC OFF indicator and TRC OFF indicator lights turn on. At this time, ABS is also prohibited and the ABS warning light turns on.
WIRING DIAGRAM


INSPECTION PROCEDURE
- NOTICE:
- When replacing the master cylinder solenoid, perform calibration (Click here).
- As there may be malfunctions in the transfer system related to when the transfer operates in L4 (for Automatic Transmission) or LL (for Manual Transmission), check the transfer system first (for automatic transmission: Click here, for manual transmission: Click here).
- When replacing the master cylinder solenoid, perform calibration (Click here).
| 1. CHECK CAN COMMUNICATION LINE |
Turn the ignition switch off.
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON.
Turn the tester on.
Select CAN Bus Check from the System Selection Menu screen and follow the prompts on the screen to inspect the CAN bus (Click here).
- OK:
- CAN Bus Check indicates no malfunctions in CAN communication.
|
|
||||
| OK | |
| 2. CHECK HARNESS AND CONNECTOR (SKID CONTROL ECU CSW CIRCUIT) |
Disconnect the A4 skid control ECU connector.
Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection
Switch Condition
Specified Condition
A4-9 (CSW) - Body ground
VSC OFF switch not pushed in
10 kΩ or higher
VSC OFF switch pushed in
Below 1 Ω
|
|
||||
| OK | |
| 3. INSPECT SKID CONTROL ECU (EXI3 TERMINAL) |
for w/ Rear Differential Lock
Disconnect the A4 skid control ECU connector.
Measure the voltage according to the value(s) in the table below.

- Standard Voltage:
Tester Connection
Switch Condition
Specified Condition
A4-40 (EXI3) - Body ground
Ignition switch ON
w/ Rear Differential Lock:
Rear differential free
11 to 14 V
Text in Illustration *a
Front view of wire harness connector
(to Skid Control ECU)
for w/o Rear Differential Lock
Disconnect the A4 skid control ECU connector.
Measure the voltage according to the value(s) in the table below.

- Standard Voltage:
Tester Connection
Switch Condition
Specified Condition
A4-40 (EXI3) - Body ground
Ignition switch ON
11 to 14 V
Text in Illustration *a
Front view of wire harness connector
(to Skid Control ECU)
Result Result
Proceed to
OK
A
NG (for w/ Rear Differential Lock)
B
NG (for w/o Rear Differential Lock)
C
|
|
||||
|
|
||||
| A | |
| 4. READ VALUE USING INTELLIGENT TESTER (TRC/VSC OFF MODE) |
Turn the ignition switch off.
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON.
Turn the tester on.
Enter the following menus: Chassis / ABS/VSC/TRAC / Data List.
ABS/VSC/TRAC Tester Display
Measurement Item/Range
Normal Condition
Diagnostic Note
TRAC/VSC Off Mode
TRAC/VSC off mode/ Normal, TRC OFF or VSC OFF
Normal: Normal mode
TRC OFF: TRAC OFF mode
VSC OFF: VSC OFF mode
-
Check that the mode display changes according to VSC OFF switch operation.
- OK:
- Display changes according to switch operation.
|
|
||||
| OK | ||
| ||
| 5. INSPECT VSC OFF SWITCH |
Remove the VSC OFF switch (Click here).
Measure the resistance according to the value(s) in the table below.

- Standard Resistance:
Tester Connection
Switch Condition
Specified Condition
3-4
Switch is not pushed
10 kΩ or higher
Switch is pushed
Below 1 Ω
Text in Illustration *a
Component without harness connected
(VSC OFF Switch)
|
|
||||
| OK | |
| 6. CHECK HARNESS AND CONNECTOR (SKID CONTROL ECU - VSC OFF SWITCH) |
Disconnect the A4 skid control ECU connector.
Disconnect the E77 VSC OFF switch connector.
Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection
Switch Condition
Specified Condition
A4-9 (CSW) - E77-3
Always
Below 1 Ω
A4-9 (CSW) - Body ground
Always
10 kΩ or higher
E77-4 - Body ground
Always
Below 1 Ω
|
|
||||
| OK | ||
| ||
| 7. INSPECT SKID CONTROL ECU (EXI3 TERMINAL) |
Disconnect the A4 skid control ECU connector.
Disconnect the L7 four wheel drive control ECU connector.
Disconnect the D2 rear differential lock indicator switch connector.
Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection
Condition
Specified Condition
A4-40 (EXI3) - Body ground
Always
10 kΩ or higher
|
|
||||
| OK | |
| 8. INSPECT REAR DIFFERENTIAL LOCK DETECTION SWITCH (DIFFERENTIAL LOCK INDICATOR SWITCH) |
Remove the rear differential lock detection switch (Click here).
Measure the resistance according to the value(s) in the table below.

- Standard Resistance:
Tester Connection
Switch Condition
Specified Condition
2 - 1
Pushed in
Below 1 Ω
Not pushed in
10 kΩ or higher
Text in Illustration *a
Component without harness connected
(Differential Lock Indicator Switch)
|
|
||||
| OK | |
| 9. INSPECT SKID CONTROL ECU (EXI3 TERMINAL) |
Disconnect the A4 skid control ECU connector.
Connect the L7 four wheel drive control ECU connector.
Measure the voltage according to the value(s) in the table below.

- Standard Voltage:
Tester Connection
Switch Condition
Specified Condition
A4-40 (EXI3) - Body ground
Ignition switch ON
11 to 14 V
Text in Illustration *a
Front view of wire harness connector
(to Skid Control ECU)
|
|
||||
| OK | ||
| ||
