2011-2016 FJ Cruiser · Service Manual BRAKE

Crawl Indicator Light Remains ON

Circuit diagnosis · Vehicles built Aug 2012 – Oct 2012

Versions by build date: Aug 2012 – Oct 2012 from Nov 2012

DESCRIPTION

When crawl control starts after operating the crawl switch, the crawl indicator light turns on.

WIRING DIAGRAM

Refer to Crawl Indicator Light does not Come ON (Click here).

INSPECTION PROCEDURE

NOTICE:
  1. When replacing the master cylinder solenoid, perform calibration (Click here).
  2. Inspect the fuses for circuits related to this system before performing the following inspection procedure.


1. CHECK CAN COMMUNICATION LINE
  1. Turn the ignition switch off.

  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the intelligent tester on.

  1. Select CAN Bus Check from the System Selection Menu screen and follow the prompts on the screen to inspect the CAN bus (Click here).

    OK:
    CAN Bus Check indicates no malfunctions in CAN communication.



NG
GO TO CAN COMMUNICATION SYSTEM (HOW TO PROCEED WITH TROUBLESHOOTING) (Click here)
OK


2. READ VALUE USING INTELLIGENT TESTER (CRAWL CONTROL SWITCH ASSEMBLY)
  1. Turn the ignition switch off.

  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the intelligent tester on.

  1. Enter the following menus: Body / D-SEAT SW / Data List.

  1. According to the display on the intelligent tester, read the Data List.

    D-SEAT SW 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    Crawl Control Main Switch
    Crawl control switch (ON/OFF switch)/ ON or OFF
    ON: Crawl switch on
    OFF: Crawl switch off
    -

    OK:
    The intelligent tester displays ON or OFF according to crawl control switch operation.



NG
Go to step 5
OK


3. READ VALUE USING INTELLIGENT TESTER (CRAWL CONTROL SWITCH ASSEMBLY)
  1. Turn the ignition switch off.

  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the intelligent tester on.

  1. Enter the following menus: Chassis / ABS/VSC/ TRC / Data List.

  1. According to the display on the intelligent tester, read the Data List.

    ABS/VSC/TRC 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    Crawl Control Light
    Crawl indicator light/ ON or OFF
    ON: Indicator light on
    OFF: Indicator light off
    -
    Crawl Control Switch
    Crawl speed selector switch status/ LOW, MIDLOW, MID, MIDHIGH or HIGH
    Actual crawl speed selector switch position
    -

    OK:
    The intelligent tester displays ON or OFF according to switch operation.



NG
Go to step 9
OK


4. PERFORM ACTIVE TEST USING INTELLIGENT TESTER
  1. Turn the ignition switch off.

  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the intelligent tester on.

  1. Perform Active Test of the combination meter using the intelligent tester (Click here).

  1. Check that the CRAWL indicator light turns on and off on the combination meter when using the intelligent tester.

    OK:
    The CRAWL indicator light turns ON or OFF according to the intelligent tester operations.



NG
GO TO METER / GAUGE SYSTEM (HOW TO PROCEED WITH TROUBLESHOOTING) (Click here)
OK

REPLACE MASTER CYLINDER SOLENOID (Click here)

5. CHECK HARNESS AND CONNECTOR (POWER SOURCE TERMINAL)

  1. C269715E06
    Turn the ignition switch off.

  1. Make sure that there is no looseness at the locking part and the connecting part of the connector.

  1. Disconnect the driving support switch control ECU connector.

  1. Check the connector case and terminals for deformation and corrosion.

    Standard condition:
    No deformation or corrosion.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    E96-2 (IG) - Body ground
    Ignition switch ON
    11 to 14 V
    E96-6 (+B) - Body ground
    Always
    11 to 14 V

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Driving Support Switch Control ECU)



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR (POWER SOURCE CIRCUIT)
OK


6. CHECK HARNESS AND CONNECTOR (GND TERMINAL)

  1. C269715E07
    Turn the ignition switch off.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    E96-16 (GND) - Body ground
    Always
    Below 1 Ω

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Driving Support Switch Control ECU)



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR (GND TERMINAL)
OK


7. CHECK HARNESS AND CONNECTOR (CRAWL CONTROL SWITCH ASSEMBLY - DRIVING SUPPORT SWITCH CONTROL ECU)
  1. Disconnect the Q3 crawl control switch assembly connector.

  1. Disconnect the E96 driving support switch control ECU connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    Q3-5 (SWI1) - E96-10 (SWO1)
    Always
    Below 1 Ω
    Q3-5 (SWI1) - Body ground
    Always
    10 kΩ or higher
    E96-10 (SWO1) - Body ground
    Always
    10 kΩ or higher
    Q3-6 (SWO2) - E96-12 (SWI2)
    Always
    Below 1 Ω
    Q3-6 (SWO2) - Body ground
    Always
    10 kΩ or higher
    E96-12 (SWI2) - Body ground
    Always
    10 kΩ or higher
    Q3-2 (SWI3) - E96-14 (SWO3)
    Always
    Below 1 Ω
    Q3-2 (SWI3) - Body ground
    Always
    10 kΩ or higher
    E96-14 (SWO3) - Body ground
    Always
    10 kΩ or higher
    Q3-8 (SWO4) - E96-4 (SWI4)
    Always
    Below 1 Ω
    Q3-8 (SWO4) - Body ground
    Always
    10 kΩ or higher
    E96-4 (SWI4) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


8. INSPECT CRAWL CONTROL SWITCH ASSEMBLY
  1. Remove the crawl control switch assembly (Click here).

  1. Inspect the crawl control switch assembly (Click here).



NG
REPLACE CRAWL CONTROL SWITCH ASSEMBLY (Click here)
OK

REPLACE DRIVING SUPPORT SWITCH CONTROL ECU (Click here)

9. CHECK HARNESS AND CONNECTOR (CRAWL CONTROL SWITCH ASSEMBLY - DRIVING SUPPORT SWITCH CONTROL ECU)
  1. Disconnect the Q3 crawl control switch assembly connector.

  1. Disconnect the E96 driving support switch control ECU connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    Q3-5 (SWI1) - E96-10 (SWO1)
    Always
    Below 1 Ω
    Q3-5 (SWI1) - Body ground
    Always
    10 kΩ or higher
    E96-10 (SWO1) - Body ground
    Always
    10 kΩ or higher
    Q3-6 (SWO2) - E96-12 (SWI2)
    Always
    Below 1 Ω
    Q3-6 (SWO2) - Body ground
    Always
    10 kΩ or higher
    E96-12 (SWI2) - Body ground
    Always
    10 kΩ or higher
    Q3-2 (SWI3) - E96-14 (SWO3)
    Always
    Below 1 Ω
    Q3-2 (SWI3) - Body ground
    Always
    10 kΩ or higher
    E96-14 (SWO3) - Body ground
    Always
    10 kΩ or higher
    Q3-8 (SWO4) - E96-4 (SWI4)
    Always
    Below 1 Ω
    Q3-8 (SWO4) - Body ground
    Always
    10 kΩ or higher
    E96-4 (SWI4) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


10. INSPECT CRAWL CONTROL SWITCH ASSEMBLY
  1. Remove the crawl control switch assembly (Click here).

  1. Inspect the crawl control switch assembly (Click here).



NG
REPLACE CRAWL CONTROL SWITCH ASSEMBLY (Click here)
OK


11. REPLACE DRIVING SUPPORT SWITCH CONTROL ECU
  1. Replace the driving support switch control ECU (Click here).


NEXT


12. READ VALUE USING INTELLIGENT TESTER (CRAWL CONTROL SWITCH ASSEMBLY)
  1. Turn the ignition switch off.

  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the intelligent tester on.

  1. Enter the following menus: Chassis / ABS/VSC/ TRC / Data List.

  1. According to the display on the intelligent tester, read the Data List.

    ABS/VSC/TRC 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    Crawl Control Light
    Crawl indicator light/ ON or OFF
    ON: Indicator light on
    OFF: Indicator light off
    -
    Crawl Control Switch
    Crawl speed selector switch status/ LOW, MIDLOW, MID, MIDHIGH or HIGH
    Actual crawl speed selector switch position
    -

    OK:
    The intelligent tester displays ON or OFF according to switch operation.



NG
REPLACE MASTER CYLINDER SOLENOID (Click here)
OK

END


← ABS Warning Light does not Come ON (from Aug 2011)Crawl Indicator Light Remains ON (from Nov 2012) →