Home › ENGINE › 1GR-FE ENGINE CONTROL SYSTEM › SFI SYSTEM

DTC    P0300    Random / Multiple Cylinder Misfire Detected

DTC    P0301    Cylinder 1 Misfire Detected

DTC    P0302    Cylinder 2 Misfire Detected

DTC    P0303    Cylinder 3 Misfire Detected

DTC    P0304    Cylinder 4 Misfire Detected

DTC    P0305    Cylinder 5 Misfire Detected

DTC    P0306    Cylinder 6 Misfire Detected

for Preparation Click here


DESCRIPTION

A093767E13
Text in Illustration 
*1
Camshaft Position Sensor
*2
Crankshaft Position Sensor
*3
ECM
When the engine misfires, high concentrations of hydrocarbons (HC) enter the exhaust gas. High HC concentration levels can cause increase in exhaust emission levels. Extremely high concentrations of HC can also cause increases in the Three-Way Catalytic Converter (TWC) temperature, which may cause damage to the TWC. To prevent this increase in emissions and to limit the possibility of thermal damage, the ECM monitors the misfire rate. When the temperature of the TWC reaches the point of thermal degradation, the ECM blinks the MIL. To monitor misfires, the ECM uses both the VVT sensor and the Crankshaft Position (CKP) sensor. The VVT sensor is used to identify any misfiring cylinders and the CKP sensor is used to measure variations in the crankshaft rotation speed. Misfires are counted when the crankshaft rotation speed variations exceed predetermined thresholds. If the misfire count exceeds the threshold levels, the ECM illuminates the MIL and stores a DTC.

DTC No.
DTC Detection Condition
Trouble Area
P0300
Simultaneous misfiring of several cylinders occurs and one of the following conditions is met (2 trip detection logic):
  1. A misfire occurs that may damage the three-way catalytic converter (MIL blinks when detect immediately).
  2. An emission deterioration misfire occurs (MIL illuminates).
  1. Open or short in engine wire harness
  2. Connector connection
  3. Vacuum hose connections
  4. Ignition system
  5. Fuel injector assembly
  6. Fuel pressure
  7. Mass Air Flow (MAF) meter
  8. Engine Coolant Temperature (ECT) sensor
  9. Compression pressure
  10. Valve timing
  11. PCV valve and hose
  12. PCV hose connections
  13. Intake system
  14. ECM
P0301
P0302
P0303
P0304
P0305
P0306
Misfiring of specific cylinder occurs and one of the following conditions is met (2 trip detection logic):
  1. A misfire occurs that may damage the three-way catalytic converter (MIL blinks when detect immediately).
  2. An emission deterioration misfire occurs (MIL illuminates).
When multiple DTCs for misfiring cylinders are stored, but DTC P0300 is not stored, it indicates that misfires have been detected in different cylinders at different times. DTC P0300 is only stored when several misfiring cylinders are detected at the same time.

MONITOR DESCRIPTION

The ECM illuminates the MIL and stores a DTC when either one of the following conditions, which could cause emission deterioration, is detected (2 trip detection logic).
  1. Within the first 1000 crankshaft revolutions of the engine starting, an excessive misfiring rate (approximately 10 to 50 misfires per 1000 crankshaft revolutions) occurs once.
  2. An excessive misfiring rate (approximately 10 to 50 misfires per 1000 crankshaft revolutions) occurs a total of 4 times.
The ECM flashes the MIL (immediate detection logic) and stores a DTC (2 trip detection logic) when either one of the following conditions, which could cause the Three-Way Catalytic Converter (TWC) damage, is detected.
  1. At a high engine rpm, a catalyst damage misfire, which is monitored every 200 crankshaft revolutions, occurs once.
  2. At a normal engine rpm, a catalyst damage misfire, which is monitored every 200 crankshaft revolutions, occurs 3 times.

HINT:
If a catalyst damage misfire occurs, the ECM informs the driver by flashing the MIL.

  1. Misfire Monitor for Mexico Models
    The ECM illuminates the MIL and stores a DTC when either one of the following conditions, which could cause emission deterioration, is detected (2 trip detection logic).
    1. Within the first 1000 crankshaft revolutions of the engine starting, an excessive misfiring rate (approximately 332 misfires per 1000 crankshaft revolutions) occurs once.
    2. An excessive misfiring rate (approximately 166 misfires per 1000 crankshaft revolutions) occurs a total of 4 times.
    The ECM flashes the MIL (immediate detection logic) and stores a DTC (2 trip detection logic) when the following condition, which could cause the Three-Way Catalytic Converter (TWC) damage, is detected.
    1. A catalyst damage misfire, which is monitored every 200 crankshaft revolutions, occurs 3 times.

MONITOR STRATEGY


Related DTCs
P0300: Multiple cylinder misfire
P0301: Cylinder 1 misfire
P0302: Cylinder 2 misfire
P0303: Cylinder 3 misfire
P0304: Cylinder 4 misfire
P0305: Cylinder 5 misfire
P0306: Cylinder 6 misfire
Required Sensors/Components (Main)
Crankshaft position sensor, VVT sensor
Required Sensors/Components (Related)
Engine coolant temperature, Intake air temperature sensors, Mass air flow meter
Frequency of Operation
Continuous
Duration
1000 crankshaft revolutions (soon after engine is started: 1 time, other 4 times) (Emissions-related misfire)
200 crankshaft revolutions (1 or 3 times) (Catalyst-damaging misfire)
MIL Operation
2 driving cycles: Emission-related misfire
MIL flashes immediately: Catalyst-damaging misfire
Sequence of Operation
None

TYPICAL ENABLING CONDITIONS


Misfire 
Monitor runs whenever following DTCs not present
P0016, P0018 (VVT system - misalignment)
P0017, P0019 (Exhaust system - misalignment)
P0102, P0103 (Mass air flow meter)
P0112, P0113 (Intake air temperature sensor)
P0115, P0117, P0118 (Engine coolant temperature sensor)
P0120 - P0123, P0220, P0222, P0223, P2135 (Throttle position sensor)
P0125 (Insufficient engine coolant temperature for closed loop fuel control)
P0327, P0328, P0332, P0333 (Knock sensor)
P0335 (Crankshaft position sensor)
P0340, P0342, P0343, P0345, P0347, P0348 (VVT sensor)
P0351 - P0356 (Igniter)
P0500 (Vehicle speed sensor)
P0705 (Shift lever position switch)
Battery voltage
8 V or more
VVT system
Not operated by scan tool
Engine speed
400 to 5900 rpm (Automatic transmission)
450 to 5900 rpm (Manual transmission)
Either of following conditions (a) or (b) met
-
(a) ECT at engine start
More than -7°C (19°F)
(b) ECT
More than 20°C (68°F)
Fuel cut
OFF

Monitor Period of Emission-Related-Misfire 
First 1000 revolutions after engine start, or Check Mode
Crankshaft 1000 revolutions
Except above
Crankshaft 1000 revolutions x 4

Monitor Period of Catalyst-Damaged-Misfire (MIL blinks) 
All of following conditions 1, 2, 3 and 4 met
Crankshaft 200 revolutions x 3
Except above (MIL blinks immediately)
Crankshaft 200 revolutions
1. Driving cycles
1st
2. Check mode
OFF
3. Engine speed
Less than 1900 rpm
4. Intake air amount per revolution
Less than 1.4 g/rev
  1. FOR MEXICO MODELS

Misfire: for Mexico Models 
Monitor runs whenever following DTCs not present
P0016, P0018 (VVT system - misalignment
P0017, P0019 (Exhaust system - misalignment)
P0102, P0103 (Mass air flow meter)
P0112, P0113 (Intake air temperature sensor)
P0115, P0117, P0118 (Engine coolant temperature sensor)
P0120 - P0123, P0220, P0222, P0223, P2135 (Throttle position sensor)
P0125 (Insufficient engine coolant temperature for closed loop fuel control)
P0327, P0328, P0332, P0333 (Knock sensor)
P0335 (Crankshaft position sensor)
P0340, P0342, P0343, P0345, P0347, P0348 (VVT sensor)
P0351 - P0356 (Igniter)
P0500 (Vehicle speed sensor)
P0705 (Shift lever position switch)
Battery voltage
8 V or more
VVT system
Not operated by scan tool
Engine speed
400 to 5900 rpm
ECT
More than 65°C (149°F)
Fuel cut
OFF

Monitor Period of Emission-Related-Misfire: for Mexico Models 
First 1000 revolutions after engine start, or Check Mode
Crankshaft 1000 revolutions
Except above
Crankshaft 1000 revolutions x 4

Monitor Period of Catalyst-Damaged-Misfire (MIL Blinks): for Mexico Models 
All of following conditions 1 and 2 met
Crankshaft 200 revolutions x 3
1. Driving cycles
1st
2. Check mode
OFF
Except above
Crankshaft 200 revolutions

TYPICAL MALFUNCTION THRESHOLDS


Monitor Period of Emission-Related-Misfire 
Misfire rate
1.5% or more (Automatic transmission)
2.44% or more (Manual transmission)

Monitor Period of Catalyst-Damaged-Misfire (MIL Blinks) 
Number of misfire per 200 revolutions
77 or more (varies with intake air amount and RPM)
  1. FOR MEXICO MODELS

Monitor Period of Emission-Related-Misfire: for Mexico Models 
Misfire rate
33.2% or more: for 1st 1000 revolutions
16.6% or more: after 1st 1000 revolutions

Monitor Period of Catalyst-Damaged-Misfire (MIL Blinks): for Mexico Models 
Number of misfire per 200 revolutions
77 or more (varies with intake air amount and RPM)
Paired cylinder misfire (MIL blinks immediately)
Detected

MONITOR RESULT

Refer to Checking Monitor Status (Click here).

CONFIRMATION DRIVING PATTERN

  1. Connect the Techstream to the DLC3.
  2. Turn the ignition switch to ON.
  3. Turn the Techstream on.
  4. Record the DTC(s) and freeze frame data.
  5. Using the Techstream, switch the ECM from normal mode to check mode (Click here).
  6. Read the misfire counts of each cylinder (Cylinder #1 Misfire Count to Cylinder #6 Misfire Count) with the engine in an idling condition. If any misfire count is displayed, skip the following confirmation driving pattern.
  7. Drive the vehicle several times with the conditions, such as engine rpm and engine load, shown in Misfire RPM and Misfire Load in the Data List.

    HINT:
    In order to store misfire DTCs, it is necessary to operate the vehicle for the period of time shown in the table below, using the Misfire RPM and Misfire Load in the Data List.

    Engine speed
    Duration
    Idling
    8 minutes or more
    1000
    4.5 minutes or more
    2000
    2.5 minutes or more
    3000
    1.5 minutes or more

  8. Check whether misfires have occurred by checking DTCs and freeze frame data.

    HINT:
    Do not turn the ignition switch off until the stored DTC(s) and freeze frame data have been recorded. When the ECM returns to normal mode (default), the stored DTC(s), freeze frame data and other data will be cleared.

  9. Record the DTC(s), freeze frame data and misfire counts.
  10. Turn the ignition switch off and wait for at least 30 seconds.
  11. Clear DTCs (even if no DTCs are stored, perform the clear DTC operation).

WIRING DIAGRAM

Refer to DTC P0102 for the mass air flow meter circuit .
Refer to DTC P0351 for the ignition coil circuit .
Refer to Fuel Injector Circuit .

INSPECTION PROCEDURE

NOTICE:
Inspect the fuses for circuits related to this system before performing the following inspection procedure.

HINT:
  1. If any DTCs other than misfire DTCs are output, troubleshoot those DTCs first.
  2. Read freeze frame data using the Techstream. Freeze frame data record the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air-fuel ratio was lean or rich, and other data, from the time the malfunction occurred.
  3. If the misfire does not recur when the vehicle is brought to the workshop, reproduce the conditions stored in the ECM as freeze frame data.
  4. If the misfire still cannot be reproduced even though the conditions stored in the ECM as freeze frame data have been reproduced, one of the following factors is considered to be a possible cause of the problem:
    1. There was insufficient fuel volume in the tank.
    2. Improper fuel is used.
    3. The spark plugs have been contaminated.
  5. After finishing repairs, check the misfire counts of the cylinders ( [Cylinder #1 Misfire Count to Cylinder #6 Misfire Count]).
  6. Be sure to confirm that no misfiring cylinder DTCs are stored again by conducting the confirmation driving pattern after finishing repairs.
  7. For 6 cylinder engine, the ECM intentionally does not set the specific misfiring cylinder DTCs at high engine speed. If misfires occur only in high engine speed areas, only DTC P0300 is stored.
    In the event of DTC P0300 being present, perform the following operations:
    1. Clear DTC (Click here).
    2. Start the engine and conduct the confirmation driving pattern.
    3. Read the misfiring rates of each cylinder or DTC(s) using the Techstream.
    4. Repair the cylinder(s) that has a high misfiring rate or is indicated by the DTC.
    5. After finishing repairs, conduct the confirmation driving pattern again, in order to verify that DTC P0300 is not stored.
  8. When one of Short FT #1, Long FT #1, Short FT #2 or Long FT #2 in the freeze frame data is outside the range of +/-15%, the air-fuel ratio may be Rich (-15% or less) or Lean (+15% or more).
  9. When the Coolant Temp in the freeze frame data is less than 75°C (167°F), the misfire has occurred only while warming up the engine.
  10. An extremely imbalanced drive wheel which causes body vibration may cause misfire DTCs detection.

1.CHECK ANY OTHER DTCS OUTPUT (IN ADDITION TO MISFIRE CODES)
  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the Techstream on.

  1. Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.

  1. Read DTCs.
    Result 
    Result
    Proceed to
    P0300, P0301, P0302, P0303, P0304, P0305 and/or P0306 is output
    A
    P0300, P0301, P0302, P0303, P0304, P0305 and/or P0306 and other DTCs are output
    B

HINT:
If any DTCs other than P0300, P0301, P0302, P0303, P0304, P0305 and P0306 are output, troubleshoot those DTCs first.



B
GO TO DTC CHART (Click here)
A


2.CHECK PCV HOSE CONNECTIONS
  1. Check the PCV hose connections (Click here).

    OK:
    PCV valve and hose are connected correctly and are not damaged.



NG
REPAIR OR REPLACE PCV HOSE
OK


3.READ VALUE USING TECHSTREAM (MISFIRE RPM AND MISFIRE LOAD)
  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to ON and turn the Techstream on.

  1. Enter the following menus: Powertrain / Engine and ECT / Data List / Misfire RPM and Misfire Load.

  1. Read and note the Misfire RPM and Misfire Load values.

    HINT:
    The Misfire RPM and Misfire Load values indicate the vehicle conditions under which the misfire occurred.


NEXT


4.READ VALUE USING TECHSTREAM (CATALYST OT MF F/C)
  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the Techstream on.

  1. Enter the following menus: Powertrain / Engine and ECT / Data List / Catalyst OT MF F/C.

  1. Read the value displayed on the Techstream.
    Result 
    Data List
    Tester Display
    Proceed to
    Catalyst OT MF F/C
    Avail
    A
    Not Avl
    B



B
Go to step 6
A


5.PERFORM ACTIVE TEST USING TECHSTREAM (PROHIBIT CAT OT F/C)
  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the Techstream on.

  1. Enter the following menus: Powertrain / Engine and ECT / Active Test / Prohibit the Catalyst OT Misfire prevent F/C.

  1. Perform the Active Test.

    NOTICE:
    When performing the Active Test, make sure the vehicle is stopped and either idling or being revved within 3000 rpm.


NEXT


6.READ VALUE USING TECHSTREAM (CYLINDER MISFIRE COUNT)
  1. Enter the following menus: Powertrain / Engine and ECT / Data List / Cylinder #1 Misfire Count, #2, #3, #4, #5 and #6

  1. Read each value for Cylinder #1 Misfire Count to #6 displayed on the Techstream. If no misfire counts occur in any cylinders, perform the following procedures:

    1. Start the engine and let it idle.

    2. Move the shift lever to the D position or first gear.

    3. Check the Cylinder #1 Misfire Count to #6.

    4. If misfire counts are still not displayed, perform steps (c) and (d).

  1. Drive the vehicle with the Misfire RPM and Misfire Load noted in the "Read Value Using Techstream (Misfire RPM and Misfire Load)" procedures above.

  1. Read the Cylinder #1 Misfire Count to #6 or DTCs displayed on the Techstream.

Result 
Result
Proceed to
Most misfires occur in only 1 or 2 cylinders
A
3 cylinders or more have equal misfire counts
B

HINT:
  1. If it is difficult to reproduce misfires for each cylinder, check the Data List item called Misfire Margin. Try to find vehicle driving conditions that lower the Misfire Margin value. Values above 30% are considered normal.
  2. If the freeze frame data's record of the ECT is below 75°C (167°F), the misfire may be detected only when the engine is cold.
  3. If the freeze frame data's record of the Engine Run Time is below 120 seconds, the misfire may be detected immediately after the engine is started.



B
Go to step 17
A


7.INSPECT SPARK PLUG
  1. Inspect the spark plug of the misfiring cylinder .

    HINT:
    Perform "Inspection After Repair" after replacing the spark plug (Click here).



NG
REPLACE SPARK PLUG (Click here)
OK


8.CHECK FOR SPARKS AND IGNITION

HINT:
  1. Refer to the ignition system inspection procedure (Click here).
  2. If the spark plugs or ignition system malfunctions, engine misfire may occur. The misfire count can be read using the Techstream. Enter the following menus: Powertrain / Engine and ECT / Data List / Cylinder #1 Misfire Count (to Cylinder #6 Misfire Count).



NG
Go to step 32
OK


9.CHECK CYLINDER COMPRESSION PRESSURE
  1. Measure the cylinder compression pressure of the misfiring cylinder .

    HINT:
    Perform "Inspection After Repair" after replacing the engine assembly (Click here).



NG
CHECK ENGINE TO DETERMINE CAUSE OF LOW COMPRESSION
OK


10.INSPECT ECM TERMINAL OF MISFIRING CYLINDER (#10, #20, #30, #40, #50 AND /OR #60 VOLTAGE)
A226857E21
  1. Turn the ignition switch to ON.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    B50-6 (#10) - B50-14 (E01)
    Ignition switch ON
    11 to 14 V
    B50-1 (#20) - B50-14 (E01)
    Ignition switch ON
    11 to 14 V
    B50-7 (#30) - B50-14 (E01)
    Ignition switch ON
    11 to 14 V
    B50-2 (#40) - B50-14 (E01)
    Ignition switch ON
    11 to 14 V
    B50-8 (#50) - B50-14 (E01)
    Ignition switch ON
    11 to 14 V
    B50-3 (#60) - B50-14 (E01)
    Ignition switch ON
    11 to 14 V

    Text in Illustration 
    *a
    Component with harness connected
    (ECM)



NG
GO TO FUEL INJECTOR CIRCUIT (Click here)
OK


11.CHECK FUEL INJECTOR OF MISFIRING CYLINDER
  1. Check the fuel injector assembly injection (whether fuel volume is high or low, and whether injection pattern is poor) (Click here).

    HINT:
    Perform "Inspection After Repair" after replacing the fuel injector assembly (Click here).



NG
REPLACE FUEL INJECTOR ASSEMBLY (Click here)
OK


12.CHECK INTAKE SYSTEM
  1. Check the intake system for vacuum leak (Click here).

    OK:
    No leak from intake system.

    HINT:
    Perform "Inspection After Repair" after repairing or replacing the intake system (Click here).



NG
REPAIR OR REPLACE INTAKE SYSTEM
OK


13.CHECK FUEL PRESSURE
  1. Check the fuel pressure .



NG
Go to step 34
OK


14.READ VALUE USING TECHSTREAM (COOLANT TEMP)
  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to ON and turn the Techstream on.

  1. Enter the following menus: Powertrain / Engine and ECT / Data List / Coolant Temp.

  1. Read the Coolant Temp twice, when the engine is both cold and warmed up.

    Standard:
    With cold engine:
    Same as ambient air temperature.
    With warm engine:
    Between 75°C and 100°C (167°F and 212°F).

    HINT:
    Perform "Inspection After Repair" after replacing the engine coolant temperature sensor (Click here).



NG
REPLACE ENGINE COOLANT TEMPERATURE SENSOR (Click here)
OK


15.READ VALUE USING TECHSTREAM (MAF)
  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the Techstream on.

  1. Enter the following menus: Powertrain / Engine and ECT / Data List / MAF and Coolant Temp.

  1. Allow the engine to idle until Coolant Temp reaches 75°C (167°F) or higher.

  1. Read MAF with the engine speed at 3000 rpm.

    Standard:
    Between 18.3 gm/sec and 25.8 gm/sec (shift lever: N (Neutral); A/C: Off).



NG
Go to step 27
OK


16.CHECK VALVE TIMING


    A135015E07
  1. Remove the cylinder head cover sub-assemblies RH and LH.

  1. Turn the crankshaft to align the alignment mark of the crankshaft.

  1. Align the notch of the crankshaft pulley to the "0" position.

  1. Check if the alignment marks of the camshaft pulley and camshaft bearing cap align.
    Text in Illustration 
    *1
    Alignment Mark

  1. Turn the crankshaft clockwise 360° if the alignment marks do not align. Check if they align once again.

    OK:
    The alignment marks of the camshaft pulley and the camshaft bearing cap align when the notch of the crankshaft pulley is in the "0" position.



OK
Go to step 27

NG
ADJUST VALVE TIMING (Click here)

17.CHECK INTAKE SYSTEM
  1. Check the intake system for vacuum leak (Click here).

    OK:
    No leak from intake system.

    HINT:
    Perform "Inspection After Repair" after repairing or replacing the intake system (Click here).



NG
REPAIR OR REPLACE INTAKE SYSTEM
OK


18.CHECK FUEL PRESSURE
  1. Check the fuel pressure .



NG
Go to step 34
OK


19.READ VALUE USING TECHSTREAM (COOLANT TEMP)
  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to ON and turn the Techstream on.

  1. Enter the following menus: Powertrain / Engine and ECT / Data List / Coolant Temp.

  1. Read the Coolant Temp twice, when the engine is both cold and warmed up.

    Standard:
    With cold engine:
    Same as ambient air temperature.
    With warm engine:
    Between 75°C and 100°C (167°F and 212°F).

    HINT:
    Perform "Inspection After Repair" after replacing the engine coolant temperature sensor (Click here).



NG
REPLACE ENGINE COOLANT TEMPERATURE SENSOR (Click here)
OK


20.READ VALUE USING TECHSTREAM (MAF)
  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the Techstream on.

  1. Enter the following menus: Powertrain / Engine and ECT / Data List / MAF and Coolant Temp.

  1. Allow the engine to idle until Coolant Temp reaches 75°C (167°F) or higher.

  1. Read MAF with the engine speed at 3000 rpm.

    Standard:
    Between 18.3 gm/sec and 25.8 gm/sec (shift lever: N (Neutral); A/C: Off).



NG
Go to step 27
OK


21.CHECK VALVE TIMING


    A135015E07
  1. Remove the cylinder head cover sub-assemblies RH and LH.

  1. Turn the crankshaft to align the alignment mark of the crankshaft.

  1. Align the notch of the crankshaft pulley to the "0" position.

  1. Check if the alignment marks of the camshaft pulley and camshaft bearing cap align.
    Text in Illustration 
    *1
    Alignment Mark

  1. Turn the crankshaft clockwise 360° if the alignment marks do not align. Check if they align once again.

    OK:
    The alignment marks of the camshaft pulley and the camshaft bearing cap align when the notch of the crankshaft pulley is in the "0" position.



NG
ADJUST VALVE TIMING (Click here)
OK


22.INSPECT SPARK PLUG
  1. Inspect the spark plug of the misfiring cylinder .

    HINT:
    Perform "Inspection After Repair" after replacing the spark plug (Click here).



NG
REPLACE SPARK PLUG (Click here)
OK


23.CHECK FOR SPARKS AND IGNITION

HINT:
  1. Refer to the ignition system inspection procedure (Click here).
  2. If the spark plugs or ignition system malfunctions, engine misfire may occur. The misfire count can be read using the Techstream. Enter the following menus: Powertrain / Engine and ECT / Data List / Cylinder #1 Misfire Count (to Cylinder #6 Misfire Count).



NG
Go to step 32
OK


24.CHECK CYLINDER COMPRESSION PRESSURE
  1. Measure the cylinder compression pressure of the misfiring cylinder .

    HINT:
    Perform "Inspection After Repair" after replacing the engine assembly (Click here).



NG
CHECK ENGINE TO DETERMINE CAUSE OF LOW COMPRESSION
OK


25.INSPECT ECM TERMINAL OF MISFIRING CYLINDER (#10, #20, #30, #40, #50 AND /OR #60 VOLTAGE)
A226857E21
  1. Turn the ignition switch to ON.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    B50-6 (#10) - B50-14 (E01)
    Ignition switch ON
    11 to 14 V
    B50-1 (#20) - B50-14 (E01)
    Ignition switch ON
    11 to 14 V
    B50-7 (#30) - B50-14 (E01)
    Ignition switch ON
    11 to 14 V
    B50-2 (#40) - B50-14 (E01)
    Ignition switch ON
    11 to 14 V
    B50-8 (#50) - B50-14 (E01)
    Ignition switch ON
    11 to 14 V
    B50-3 (#60) - B50-14 (E01)
    Ignition switch ON
    11 to 14 V

    Text in Illustration 
    *a
    Component with harness connected
    (ECM)



NG
GO TO FUEL INJECTOR CIRCUIT (Click here)
OK


26.CHECK FUEL INJECTOR OF MISFIRING CYLINDER
  1. Check the fuel injector assembly injection (whether fuel volume is high or low, and whether injection pattern is poor) (Click here).

    HINT:
    Perform "Inspection After Repair" after replacing the fuel injector assembly (Click here).



NG
REPLACE FUEL INJECTOR ASSEMBLY (Click here)
OK


27.CHECK HARNESS AND CONNECTOR (MASS AIR FLOW METER CONNECTOR CONNECTION)
  1. Check the connection and terminal contact pressure of connectors and wire harnesses between the mass air flow meter and ECM (Click here).

    HINT:
    Repair any problems.


NEXT


28.CHECK WHETHER DTC OUTPUT RECURS
  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the Techstream on.

  1. Clear the DTCs (Click here).

  1. Turn the ignition switch off and wait for at least 30 seconds.

  1. Turn the ignition switch to ON and turn the Techstream on.

  1. Start the engine and warm it up.

  1. Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.

  1. Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.

  1. Input the DTC: P0300, P0301, P0302, P0303, P0304, P0305 and P0306.

  1. Check the DTC judgment result.
    Result 
    Result
    Proceed to
    ABNORMAL
    (P0300, P0301, P0302, P0303, P0304, P0305 or P0306 is output)
    A
    NORMAL
    (No DTC is output)
    B



B
END
A


29.CHECK HARNESS AND CONNECTOR (MASS AIR FLOW METER - ECM)
  1. Disconnect the B51 mass air flow meter connector.

  1. Disconnect the B48 ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:

    Tester Connection
    Condition
    Specified Condition
    B51-5 (VG) - B48-14 (VG)
    Always
    Below 1 Ω
    B51-4 (E2G) - B48-13 (E2G)
    Always
    Below 1 Ω
    B51-5 (VG) or B48-14 (VG) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


30.REPLACE MASS AIR FLOW METER
  1. Replace the mass air flow meter (Click here).

    HINT:
    1. If the results of the inspections performed in steps 15 and 20 indicated no problem, proceed to the next step without replacing the mass air flow meter.
    2. Perform "Inspection After Repair" after replacing the mass air flow meter (Click here).


NEXT


31.CHECK WHETHER DTC OUTPUT RECURS
  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the Techstream on.

  1. Clear the DTCs (Click here).

  1. Turn the ignition switch off and wait for at least 30 seconds.

  1. Turn the ignition switch to ON and turn the Techstream on.

  1. Start the engine and warm it up.

  1. Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.

  1. Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.

  1. Input the DTC: P0300, P0301, P0302, P0303, P0304, P0305 and P0306.

  1. Check the DTC judgment result.
    Result 
    Result
    Proceed to
    NORMAL
    (No DTC is output)
    A
    ABNORMAL
    (P0300, P0301, P0302, P0303, P0304, P0305 or P0306 is output)
    B



B
REPLACE ECM (Click here)
A

END 

32.CHANGE TO NORMAL SPARK PLUG AND CHECK SPARK OF MISFIRING CYLINDER
  1. Change the installed spark plug to a spark plug that functions normally.

  1. Perform a spark test.

    CAUTION:
    Always disconnect all of the fuel injector assembly connectors.

    NOTICE:
    Do not crank the engine for more than 2 seconds.

    1. Install the spark plug to the ignition coil assembly and connect the ignition coil assembly connector.

    2. Disconnect the fuel injector assembly connector.

    3. Ground the spark plug.

    4. Check if sparks occur while the engine is being cranked.

      OK:
      Sparks jump across electrode gap.

      HINT:
      Perform "Inspection After Repair" after replacing the spark plug (Click here).



NG
Go to step 33
OK

REPLACE SPARK PLUG (Click here)  

33.CHANGE TO NORMAL IGNITION COIL AND CHECK SPARK OF MISFIRING CYLINDER
  1. Change the installed ignition coil assembly to a ignition coil assembly that functions normally.

  1. Perform a spark test.

    CAUTION:
    Always disconnect all of the fuel injector assembly connectors.

    NOTICE:
    Do not crank the engine for more than 2 seconds.

    1. Install the spark plug to the ignition coil assembly and connect the ignition coil assembly connector.

    2. Disconnect the B11, B25, B10, B21, B9 and B18 fuel injector assembly connectors.

    3. Ground the spark plug.

    4. Check if sparks occur while the engine is being cranked.

      OK:
      Sparks jump across electrode gap.

      HINT:
      Perform "Inspection After Repair" after replacing the ignition coil assembly (Click here).



NG
REPLACE ECM (Click here)
OK

REPLACE IGNITION COIL ASSEMBLY (Click here)  

34.CHECK FUEL LINE
  1. Check the fuel lines for leaks or blockage.

    OK:
    No leakage or blockage in the fuel line.

    HINT:
    Perform "Inspection After Repair" after replacing the fuel pump (Click here).



NG
REPAIR OR REPLACE FUEL LINE
OK

REPLACE FUEL PUMP (Click here)