Home › ENGINE › 1GR-FE ENGINE CONTROL SYSTEM › SFI SYSTEM

DTC    P2440    Secondary Air Injection System Switching Valve Stuck Open Bank1

DTC    P2441    Secondary Air Injection System Switching Valve Stuck Close Bank1

DTC    P2442    Secondary Air Injection System Switching Valve Stuck Open Bank 2

DTC    P2443    Secondary Air Injection System Switching Valve Stuck Closed Bank 2

for Preparation Click here


DESCRIPTION

Refer to DTC P0412 .

DTC No.
DTC Detection Condition
Trouble Area
P2440
Cumulative pressure pulsation is 60 kPa (450 mmHg) or more for 2 seconds (1 trip detection logic).
  1. Emission control valve set (for bank 1)
  2. Open or short in emission control valve set (for bank 1) circuit
  3. Secondary air injection system piping
  4. Pressure sensor (Emission control valve set (for bank 1))
  5. Pressure sensor (Emission control valve set (for bank 1)) circuit
  6. Air injection control driver
  7. ECM
The emission control valve set (for bank 1) is stuck open for 7 seconds while the engine is running (1 trip detection logic).
P2441
The emission control valve set (for bank 1) is stuck closed for 7 seconds while the engine is running (2 trip detection logic).
  1. Emission control valve set (for bank 1)
  2. Open or short in emission control valve set (for bank 1) circuit
  3. Secondary air injection system piping
  4. Pressure sensor (Emission control valve set (for bank 1))
  5. Pressure sensor (Emission control valve set (for bank 1)) circuit
  6. Air injection control driver
  7. ECM
  8. Open or short in air pump heater circuit
  9. Air pump heater relay (AIR PMP HTR)
  10. Air pump assembly
P2442
Cumulative pressure pulsation is 60 kPa (450 mmHg) or more for 2 seconds (1 trip detection logic).
  1. No. 2 emission control valve set (for bank 2)
  2. Open or short in No. 2 emission control valve set (for bank 2) circuit
  3. Secondary air injection system piping
  4. Pressure sensor (No. 2 emission control valve set (for bank 2))
  5. Pressure sensor (No. 2 emission control valve set (for bank 2)) circuit
  6. Air injection VSV relay (AI-VSV)
  7. ECM
The No. 2 emission control valve set (for bank 2) is stuck open for 7 seconds while the engine is running (1 trip detection logic).
P2443
The No. 2 emission control valve set (for bank 2) is stuck closed for 7 seconds while the engine is running (2 trip detection logic).
  1. No. 2 emission control valve set (for bank 2)
  2. Open or short in No. 2 emission control valve set (for bank 2) circuit
  3. Secondary air injection system piping
  4. Pressure sensor (No. 2 emission control valve set (for bank 2))
  5. Pressure sensor (No. 2 emission control valve set (for bank 2)) circuit
  6. Air injection VSV relay (AI-VSV)
  7. ECM
  8. Open or short in air pump heater circuit
  9. Air pump heater relay (AIR PMP HTR)
  10. Air pump assembly

HINT:
Emission control valve set normal operation:
When the emission control valve set is open, exhaust gas pulsation occurs in the secondary air passage.
When the emission control valve set is closed, exhaust gas pulsation does not occur in the secondary air passage.


MONITOR DESCRIPTION

DTCs P2440 and P2442 indicate that the emission control valve set is stuck open. DTCs P2441 and P2443 indicate that the emission control valve set is stuck closed. The ECM performs diagnosis of the secondary air injection system based on the changes in pressure and the pressure pulsation. If a malfunction is detected, the ECM illuminates the MIL and stores a DTC.

MONITOR STRATEGY


Related DTCs
P2440: Emission control valve (Bank 1) stuck open
P2441: Emission control valve (Bank 1) stuck closed
P2442: Emission control valve (Bank 2) stuck open
P2443: Emission control valve (Bank 2) stuck closed
Required Sensors/Components (Main)
Pressure sensor (Emission control valve set)
Required Sensors/Components (Related)
-
Frequency of Operation
Continuous: P2440 Case 2, P2442 Case 2
Once per driving cycle: Others
Duration
2 seconds: P2440 Case 2, P2442 Case 2
7 seconds: Others
MIL Operation
1 driving cycle: P2440, P2442
2 driving cycles: Others
Sequence of Operation
None

TYPICAL ENABLING CONDITIONS


All 
Monitor runs whenever following DTCs not stored
P0010, P0020 (VVT oil control valve)
P0011, P0021 (VVT system - advance)
P0012, P0022 (VVT system - retard)
P0013, P0023 (Exhaust VVT oil control valve)
P0014, P0024 (Exhaust VVT system - advance)
P0015, P0025 (Exhaust VVT system - retard)
P0016, P0018 (VVT system - misalignment)
P0017, P0019 (Exhaust VVT system - Misalignment)
P0031, P0032, P0051, P0052, P101D, P103D (Air fuel ratio sensor heater)
P0102, P0103 (Mass air flow meter)
P0112, P0113 (Intake air temperature sensor)
P0115, P0117, P0118 (Engine coolant temperature sensor)
P0120 - P0123, P0220, P0222, P0223, P2135 (Throttle position sensor)
P0125 (Insufficient coolant temperature for closed loop fuel control)
P014C - P014F, P015A - P015D, P2195 - P2198, P2237 - P2242, P2252, P2253, P2255, P2256 (Air fuel ratio sensor)
P0171, P0172, P0174, P0175 (Fuel system)
P0301 - P0306 (Misfire)
P0327, P0328, P0332, P0333 (Knock sensor)
P0335 (Crankshaft position sensor)
P0340, P0342, P0343, P0345, P0347, P0348 (VVT sensor)
P0351 - P0356 (Igniter)
P0365, P0367, P0368, P0390, P0392, P0393 (Exhaust VVT sensor)
P0451 - P0453 (EVAP system)
P0500, P0722 (Vehicle speed sensor)
P106B (Evap. emission control system pressure sensor - Air injection system pressure sensor correlation)
P219A, P219B (Air-fuel ratio imbalance)
P2431 - P2433, P2436 - P2438 (Secondary air injection system pressure sensor)

P2440 (Case 1), P2441, P2442 (Case 1), P2443 
Battery voltage
11 V or higher
Atmospheric pressure
45 kPa (338 mmHg) or higher
Engine
Running
Pressure pattern check during secondary air injection ON*1
Completed
Pressure pattern check during secondary air injection OFF*2
Completed
Pressure change check: secondary air injection ON*3
Completed
Pressure pulsation check: secondary air injection OFF*4
Completed
Air injection control driver failure (open/short or out of range)
Not detected
Secondary air injection pressure sensor failure (open/short or out of range)
Not detected

*1: Pressure pattern check during secondary air injection ON
-
Time after secondary air injection starts operation
5 seconds or more
Air pump
ON
Emission control valve
Open
Engine speed
Less than 3750 rpm
Engine speed
680 rpm or more
Intake air amount
Less than 100 gm/sec
Time after engine started
5 seconds or more

*2: Pressure pattern check during secondary air injection OFF
-
Time after secondary air injection starts operation
10 seconds or more
Air pump
OFF
Emission control valve
Closed
Engine speed
Less than 3000 rpm
Secondary air injection monitor during secondary air injection ON
Completed
Time after engine started
5 seconds or more

*3: Pressure change check: secondary air injection ON
-
Secondary air injection
Operating
Air pump
ON
Emission control valve (bank 2)
Open
Emission control valve (bank 1)
Closed
Secondary air injection pressure sensor failure (open/short or out of range)
Not detected
Intake air amount
Less than 15 gm/sec

*4: Pressure pulsation check: secondary air injection OFF
-
Pressure change check: secondary air injection ON
Completed
Pressure pulsation check: secondary air injection OFF
Not completed
Air pump
ON
Time after emission control valve (bank 2) closes
0.3 seconds or more
Emission control valve (bank 1)
Open
Engine speed
Less than 5000 rpm

P2440, P2442 Emission Control Valve is Stuck Open (Case 2) 
One of the following conditions is met
(a), (b) or (c)
(a) Cumulative intake air amount
110 gm/sec or more
(b) Difference between starting temperature and current temperature
30°C (86°F) or more
(c) Starting coolant temperature
45°C (113°F) or higher
Air pump
OFF
Emission control valve
Closed
Engine speed
5000 rpm or less
Secondary air injection system pressure sensor failure (open/short or out of range)
Not detected
Time after engine started
5 seconds or more
Time after secondary air injection starts operation
10 seconds or more
Emission control valve stuck open (DTC P2440, P2442)
Not detected
Secondary air injection system pressure sensor stuck (DTC P2445)
Not in operation
Engine load
20% or more

TYPICAL MALFUNCTION THRESHOLDS


P2440 Emission Control Valve is Stuck Open (Case 1) 
One of the following conditions is met
(a), (b) or (c)
(a) Condition 2 (secondary air injection ON) and Condition 2 (secondary air injection OFF)
-
(b) Condition 1 (secondary air injection ON) and Condition 1 (secondary air injection OFF)
-
(c) Condition 1 (secondary air injection ON) and Condition 2 (secondary air injection OFF)
-

P2442 Emission Control Valve is Stuck Open (Case 1) 
One of the following conditions is met
(a), (b) or (c)
(a) Condition 2 (secondary air injection ON) and Condition 2 (secondary air injection OFF)
-
(b) Condition 1 (secondary air injection ON), Condition 1 (secondary air injection OFF), no pressure change detected when secondary air injection ON and pressure pulsation detected when secondary air injection OFF
-
(c) Condition 1 (secondary air injection ON), Condition 2 (secondary air injection OFF), no pressure change detected when secondary air injection ON and pressure pulsation detected when secondary air injection OFF
-

P2440, P2442 Emission Control Valve is Stuck Open (Case 2) 
Cumulative pressure pulsation
60 kPa (450 mmHg) or higher

P2441 Emission Control Valve is Stuck Closed 
One of the following conditions is met
(a), (b) or (c)
(a) Condition 3 (secondary air injection ON)
-
(b) Condition 1 (secondary air injection ON), pressure change detected when secondary air injection ON and no pressure pulsation detected when secondary air injection OFF
-
(c) Condition 4 (secondary air injection ON)
-

P2443 Emission Control Valve is Stuck Closed 
One of the following conditions is met
(a), (b), (c) or (d)
(a) Condition 3 (secondary air injection ON)
-
(b) Condition 1 (secondary air injection ON), Condition 3 (secondary air injection OFF), no pressure change detected when secondary air injection ON and pressure pulsation detected when secondary air injection OFF
-
(c) Condition 1 (secondary air injection ON), Condition 4 (secondary air injection OFF), no pressure change detected when secondary air injection ON and pressure pulsation detected when secondary air injection OFF
-
(d) Condition 4 (secondary air injection ON)
-

Secondary Air Injection ON (Condition 1) 
Both conditions are met during secondary air injection ON
-
Cumulative pressure pulsation
1.25 kPa (9.3 mmHg) or higher
Secondary air injection pressure
1 kPa (7.5 mmHg) or higher

Secondary Air Injection ON (Condition 2) 
Both conditions are met during secondary air injection ON
-
Cumulative pressure pulsation
1.25 kPa (9.3 mmHg) or higher
Secondary air injection pressure
Below 1 kPa (7.5 mmHg)

Secondary Air Injection ON (Condition 3) 
Both conditions are met during secondary air injection ON
-
Cumulative pressure pulsation
Below 1.25 kPa (9.3 mmHg)
Secondary air injection pressure
1 kPa (7.5 mmHg) or higher

Secondary Air Injection ON (Condition 4) 
Both conditions are met during secondary air injection ON
-
Cumulative pressure pulsation
Below 1.25 kPa (9.3 mmHg)
Secondary air injection pressure
Below 1 kPa (7.5 mmHg)

Secondary Air Injection OFF (Condition 1) 
Both conditions are met during secondary air injection OFF
-
Cumulative pressure pulsation
10 kPa (75 mmHg) or higher
Secondary air injection pressure
2.5 kPa (18.7 mmHg) or higher

Secondary Air Injection OFF (Condition 2) 
Both conditions are met during secondary air injection OFF
-
Cumulative pressure pulsation
10 kPa (75 mmHg) or higher
Secondary air injection pressure
Below 2.5 kPa (18.7 mmHg)

Secondary Air Injection OFF (Condition 3) 
Both conditions are met during secondary air injection OFF
-
Cumulative pressure pulsation
Below 10 kPa (75 mmHg)
Secondary air injection pressure
2.5 kPa (18.7 mmHg) or higher

Secondary Air Injection OFF (Condition 4) 
Both conditions are met during secondary air injection OFF
-
Cumulative pressure pulsation
Below 10 kPa (75 mmHg)
Secondary air injection pressure
Below 2.5 kPa (18.7 mmHg)

HINT:
Refer to "Data List / Active Test" [Air Pump Pressure (Absolute), Air Pump2 Pressure (Absolute) and Air Pump Pulsation Pressure] (Click here).


MONITOR RESULT

Refer to Checking Monitor Status (Click here).

CONFIRMATION DRIVING PATTERN

NOTICE:
  1. This Secondary Air Injection Check only allows technicians to operate the secondary air injection system for a maximum of 5 seconds. Furthermore, the check can only be performed up to 4 times per trip. If the test is repeated, intervals of at least 30 seconds are required between checks. While secondary air injection system operation using the Techstream is prohibited, the Techstream display indicates the prohibition (WAIT or ERROR). If ERROR is displayed on the Techstream during the test, stop the engine for 10 minutes, and then try again.
  2. Performing Secondary Air Injection Check repeatedly may cause damage to the secondary air injection system. If it is necessary to repeat the check, leave an interval of several minutes between System Check operations to prevent the system from overheating.
  3. When performing the Secondary Air Injection Check operation after the battery cable has been reconnected, wait for 7 minutes with the ignition switch turned to ON or the engine running.
  4. Turn the ignition switch off when the Secondary Air Injection Check operation finishes.

  1. Start the engine and warm it up.
  2. Turn the ignition switch off.
  3. Connect the Techstream to the DLC3.
  4. Turn the ignition switch to ON.
  5. Turn the Techstream on.
  6. Clear the DTCs (even if no DTCs are stored, perform the clear DTC operation).
  7. Turn the ignition switch off and wait for at least 30 seconds.
  8. Turn the ignition switch to ON and turn the Techstream on.
  9. Enter the following menus: Powertrain / Engine and ECT / Utility / Secondary Air Injection Check / Automatic Mode.
  10. Start the engine after the Techstream initialization is finished.
  11. Perform the System Check operation by pressing Next.
  12. Perform the following to confirm the secondary air injection system pending DTCs: Press the Exit.
  13. Enter the following menus: Powertrain / Engine and ECT / Trouble codes.
  14. Read pending DTCs.

    HINT:
    1. If a pending DTC is output, the system is malfunctioning.
    2. If a pending DTC is not output, perform the following procedure.

  15. After Secondary Air Injection Check is completed, check All Readiness by entering the following menus: Powertrain / Engine and ECT / Utility / All Readiness.
  16. Input the DTC: P2440, P2441, P2442 or P2443.
  17. Check the DTC judgment result.

    Techstream Display
    Description
    NORMAL
    1. DTC judgment completed
    2. System normal
    ABNORMAL
    1. DTC judgment completed
    2. System abnormal
    INCOMPLETE
    1. DTC judgment not completed
    2. Perform driving pattern after confirming DTC enabling conditions
    N/A
    1. Unable to perform DTC judgment
    2. Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit

    HINT:
    1. If the judgment result shows NORMAL, the system is normal.
    2. If the judgment result shows ABNORMAL, the system has a malfunction.

  18. If the judgment result is INCOMPLETE or N/A and no pending DTC is output, perform a universal trip and check for permanent DTCs (Click here).

    HINT:
    1. If no permanent DTC is output, the system is normal.
    2. If a permanent DTC is output, the system is malfunctioning.

  19. Turn the ignition switch off.

WIRING DIAGRAM

Refer to DTC P0412 .
Refer to DTC P0416, P0417 .

INSPECTION PROCEDURE

HINT:
Refer to "Data List / Active Test" [Air Pump Pressure (Absolute), Air Pump2 Pressure (Absolute) and Air Pump Pulsation Pressure] (Click here).

HINT:
Determination by ECM monitoring:
The ECM detects malfunctions in the secondary air injection system by detecting the pressure in the secondary air injection passage between the air pump assembly and emission control valve set and stores a DTC. Soon after a cold engine start, the monitor runs for a short time while the secondary air injection system is both ON and OFF. The ECM detects both the pressure and the exhaust pulsation and compares them.
The following 8 patterns are secondary air injection system pressure conditions in the secondary air injection system passage.


Pressure Condition in Secondary Air Injection System Case 1 
Air Pump Assembly
ON
Emission Control Valve Set
Open
Pressure
1 kPa (7.5 mmHg) or higher
Pulsation Detection
Exhaust gas pulsation detected

Pressure Condition in Secondary Air Injection System Case 2 
Air Pump Assembly
OFF
Emission Control Valve Set
Open
Pressure
Below 2.5 kPa (18.7 mmHg)
Pulsation Detection
Exhaust gas pulsation detected

Pressure Condition in Secondary Air Injection System Case 3 
Air Pump Assembly
ON
Emission Control Valve Set
Closed
Pressure
1 kPa (7.5 mmHg) or higher
Pulsation Detection
Exhaust gas pulsation not detected

Pressure Condition in Secondary Air Injection System Case 4 
Air Pump Assembly
OFF
Emission Control Valve Set
Closed
Pressure
Below 2.5 kPa (18.7 mmHg)
Pulsation Detection
Exhaust gas pulsation not detected

Pressure Condition in Secondary Air Injection System Case 5 
Air Pump Assembly
ON
Emission Control Valve Set
Open
Pressure
1 kPa (7.5 mmHg) or higher
Pulsation Detection
Exhaust gas pulsation detected

Pressure Condition in Secondary Air Injection System Case 6 
Air Pump Assembly
OFF
Emission Control Valve Set
Open
Pressure
Below 2.5 kPa (18.7 mmHg)
Pulsation Detection
Exhaust gas pulsation detected

Pressure Condition in Secondary Air Injection System Case 7 
Air Pump Assembly
ON
Emission Control Valve Set
Closed
Pressure
1 kPa (7.5 mmHg) or higher
Pulsation Detection
Exhaust gas pulsation not detected

Pressure Condition in Secondary Air Injection System Case 8 
Air Pump Assembly
OFF
Emission Control Valve Set
Closed
Pressure
Below 2.5 kPa (18.7 mmHg)
Pulsation Detection
Exhaust gas pulsation not detected
If the detected pressure is high, the air pump assembly is assumed to be ON and if it alternates sharply, the emission control valve set is assumed to be open. The ECM detects malfunctions from the combination of pressures detected when the secondary air injection system is ON and OFF.

HINT:
The exhaust pulsation value is calculated in the ECM. If the calculated value exceeds a certain level, the ECM determines that the exhaust pulsation is in the secondary air injection system.

HINT:
  1. In cases 3 and 7, as the pressure sensor detects a slight pump operation pulsation, the detected value is not constant. Since the pump outlet is blocked by closing the emission control valve set, the average pressure is higher than in case 1 (approximately 15 to 25 kPa (112.5 to 187.5 mmHg)).
  2. In case 1, the average pressure is approximately 3 to 11 kPa (22.5 to 82.5 mmHg). The value of 1 kPa indicated in the table above is a threshold for detecting pump malfunctions.


Detected Condition while Secondary Air Injection Operating:
Air Pump Assembly ON, Emission Control Valve Set Open
Detected Condition while Secondary Air Injection not Operating:
Air Pump Assembly OFF, Emission Control Valve Set Closed
ECM Determination
DTC Output
Case 1
Case 8
Normal
-
Case 1
Case 6
Emission control valve set stuck open
P2440
or
P2442
Case 1
Case 7
Air pump assembly stuck ON
P2444
Case 2
Case 8
Air pump assembly stuck OFF
P2445
Case 3
Case 8
Emission control valve set stuck closed
P2441
or
P2443
Case 1
Case 5
Emission control valve set stuck open and air pump assembly stuck ON
P2440 and/or P2442
and
P2444
Case 2
Case 6
Emission control valve set stuck open and air pump assembly stuck OFF
P2440 and/or P2442
and
P2445
Case 3
Case 7
Emission control valve set stuck closed and air pump assembly stuck ON
P2441 and/or P2443
and
P2444
Case 4
Case 8
Emission control valve set stuck closed and air pump assembly stuck OFF
P2441 and/or P2443
and
P2445

HINT:
  1. By using the Techstream to perform the Secondary Air Injection Check operation in the System Check, the air-fuel ratio and the pressure in the secondary air injection system passage can be checked while the secondary air injection system is operating. This helps technicians to troubleshoot the system when it malfunctions. Furthermore, pending codes also can be checked by performing Utility / Secondary Air Injection Check / Automatic Mode after the repair.
  2. Read freeze frame data using the Techstream. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air-fuel ratio was lean or rich, and other data from the time the malfunction occurred.

  1. System Check:

    NOTICE:
    1. This Secondary Air Injection Check only allows technicians to operate the secondary air injection system for a maximum of 5 seconds. Furthermore, the check can only be performed up to 4 times per trip. If the test is repeated, intervals of at least 30 seconds are required between checks. While secondary air injection system operation using the Techstream is prohibited, the Techstream display indicates the prohibition (WAIT or ERROR). If ERROR is displayed on the Techstream during the test, stop the engine for 10 minutes, and then try again.
    2. Performing Secondary Air Injection Check repeatedly may cause damage to the secondary air injection system. If it is necessary to repeat the check, leave an interval of several minutes between System Check operations to prevent the system from overheating.
    3. When performing the Secondary Air Injection Check operation after the battery cable has been reconnected, wait for 7 minutes with the ignition switch turned to ON or the engine running.
    4. Turn the ignition switch off when the Secondary Air Injection Check operation finishes.

  2. The pressure in the secondary air passage can be checked using the Techstream.
    1. Start the engine and warm it up.
    2. Turn the ignition switch off.
    3. Connect the Techstream to the DLC3.
    4. Turn the ignition switch to ON.
    5. Turn the Techstream on.
    6. Enter the following menus: Powertrain / Engine and ECT / Utility / Secondary Air Injection Check / Manual Mode / AIR PUMP: ON, ASV 1: OPEN, ASV 2: OPEN and AIR PUMP: OFF, ASV 1: CLOSE, ASV 2: CLOSE.

      HINT:
      When Manual Mode is selected, the Techstream initialization (atmospheric pressure measurement) is performed automatically. The initialization takes 10 seconds. After the initialization, AIR PUMP and ASV operation can be selected.

    7. Start the engine.
    8. Perform the secondary air injection system forced operation while the engine is idling.
    9. Check that the Data List values for the air pump (AIR PUMP), emission control valve (ASV) and pressure in the secondary air injection system passage (PRESSURE) displayed on the Techstream are as shown in the table below.

      Standard:

      Techstream Operation
      Air Pump Assembly
      Emission Control Valve Set
      Pressure*1
      Pulsation*2
      AIR PUMP: ON, ASV: OPEN
      ON
      OPEN
      1 kPa (7.5 mmHg) or higher
      1.25 kPa (9.3 mmHg) or higher
      AIR PUMP: OFF, ASV: CLOSE
      OFF
      CLOSE
      Below 2.5 kPa (18.7 mmHg)
      Below 10 kPa (75 mmHg)

      *1: Average pumping pressure (gauge pressure). The pressure should be 1 kPa or higher when the secondary air injection system operates.
      *2: The cumulative exhaust pulsation calculated by the ECM. If the calculated value exceeds a certain level, the ECM determines that the exhaust pulsation is in the secondary air injection system.
    10. Turn the ignition switch off.

      NOTICE:
      Inspect the fuses for circuits related to this system before performing the following inspection procedure.

      HINT:
      1. Bank 1 refers to the bank that includes the No. 1 cylinder*.
        *: The No. 1 cylinder is the cylinder which is farthest from the transmission.
      2. Bank 2 refers to the bank that does not include the No. 1 cylinder.

1.CHECK FOR ANY OTHER DTCS OUTPUT (IN ADDITION TO SECONDARY AIR INJECTION SYSTEM DTCS)
  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the Techstream on.

  1. Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.

  1. Read the DTCs and freeze frame data.
    Result 
    Result
    Proceed to
    P2440, P2441, P2442 and/or P2443 is output
    A
    P2440 and/or P2441 and P0412 are output
    B
    P2442 and/or P2443 and P0416 and/or P0417 are output
    C
    P2440, P2441, P2442 and/or P2443 and other DTCs (except P0412, P0416 and P0417) are output
    D

    HINT:
    If any DTCs other than P0412, P0416, P0417, P2440, P2441, P2442 and P2443 are output, troubleshoot those DTCs first.



B
GO TO EMISSION CONTROL VALVE INSPECTION PROCEDURE (P0412)

C
GO TO EMISSION CONTROL VALVE INSPECTION PROCEDURE (P0416 AND P0417)

D
GO TO DTC CHART (Click here)
A


2.CHECK FREEZE FRAME DATA (AIR PUMP FREEZE, AIR SWITCHING VALVE FREEZE AND AIR SWITCHING VALVE2 FREEZE)
  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to ON and turn the Techstream on.

  1. Read the values of Air Pump Freeze, Air Switching Valve Freeze and Air Switching Valve2 Freeze from the freeze frame data recorded previously.

  1. Referring to the following table, proceed to the appropriate step according to the result of the data reading.

    Result 
    Result
    Proceed to
    Air Pump Freeze
    Air Switching Valve Freeze
    Air Switching Valve2 Freeze
    OFF
    OFF
    OFF
    B
    Except above
    A



B
Go to step 8
A


3.PERFORM ACTIVE TEST USING TECHSTREAM (ACTIVE THE AIR PUMP HEATER)


    A221585E10
  1. Disconnect the air pump assembly connector.

  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to ON and turn the Techstream on.

  1. Enter the following menus: Powertrain / Engine and ECT/ Active Test / Activate the Air Pump Heater.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    A36-1 (APH+) - Body ground
    Activate the Air Pump Heater is ON
    11 to 14 V

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Air Pump Assembly)



NG
Go to step 5
OK


4.INSPECT AIR PUMP ASSEMBLY (HEATER RESISTANCE)
  1. Inspect the air pump assembly (Click here).



NG
REPLACE AIR PUMP ASSEMBLY (Click here)
OK


5.INSPECT AIR PUMP HEATER RELAY (AIR PMP HTR)
  1. Inspect the air pump heater relay (AIR PMP HTR) .



NG
REPLACE AIR PUMP HEATER RELAY (AIR PMP HTR)
OK


6.CHECK AIR PUMP HEATER RELAY (AIR PMP HTR) (POWER SOURCE)
  1. Remove the air pump heater relay (AIR PMP HTR) from the engine room relay block.



    A287418E01
  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    5 (Air pump heater relay (AIR PMP HTR)) - Body ground
    Always
    11 to 14 V

    Text in Illustration 
    *1
    Engine Room Relay Block
    *2
    Air Pump Heater Relay (AIR PMP HTR)



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


7.CHECK HARNESS AND CONNECTOR (AIR PUMP ASSEMBLY - AIR PUMP HEATER RELAY (AIR PMP HTR) - BODY GROUND)
  1. Remove the air pump heater relay (AIR PMP HTR) from the engine room relay block.

  1. Disconnect the A36 air pump assembly connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:

    Tester Connection
    Condition
    Specified Condition
    3 (Air pump heater relay (AIR PMP HTR)) - A36-1 (APH+)
    Always
    Below 1 Ω
    A36-3 (APHG) - Body ground
    Always
    Below 1 Ω
    3 (Air pump heater relay (AIR PMP HTR)) or A36-1 (APH+) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


8.INSPECT AIR PUMP ASSEMBLY
  1. Inspect the air pump assembly (Click here).



NG
REPLACE AIR PUMP ASSEMBLY (Click here)
OK


9.PERFORM ACTIVE TEST USING TECHSTREAM (SECONDARY AIR INJECTION SYSTEM OPERATION)
A221579E02
  1. Perform a visual check:

    1. Start the engine and warm it up.

    2. Turn the ignition switch off.

    3. Disconnect the air hoses.

    4. Connect the Techstream to the DLC3.

    5. Turn the ignition switch to ON.

    6. Turn the Techstream on.

    7. Enter the following menus: Powertrain / Engine and ECT / Utility / Secondary Air Injection Check / Manual Mode / AIR PUMP: ON, ASV1: OPEN, ASV2: OPEN.

      HINT:
      When Manual Mode is selected, the Techstream initialization (atmospheric pressure measurement) is performed automatically. The initialization takes 10 seconds. After the initialization, AIR PUMP and ASV operation can be selected.

    8. Start the engine.

    9. Perform the secondary air injection system forced operation while the engine is idling.

    10. Place your hand near the emission control valve port and check that the exhaust gas pressure pulsates when the emission control valve is turned on.

      CAUTION:
      To avoid the danger of being burned by the exhaust gas, bring your hand close to the valve port slowly.

    11. Enter the following menus: Powertrain / Engine and ECT / Utility / Secondary Air Injection Check / Manual Mode / AIR PUMP: ON, ASV1: OPEN, ASV2: OPEN and AIR PUMP: ON, ASV1: CLOSE, ASV2: CLOSE.

    12. Check that the exhaust gas does not pulsate when the emission control valve is turned off.

    13. Turn the ignition switch off.

      NOTICE:
      1. This Secondary Air Injection Check only allows technicians to operate the secondary air injection system for a maximum of 5 seconds. Furthermore, the check can only be performed up to 4 times per trip. If the test is repeated, intervals of at least 30 seconds are required between checks. While secondary air injection system operation using the Techstream is prohibited, the Techstream display indicates the prohibition (WAIT or ERROR). If ERROR is displayed on the Techstream during the test, stop the engine for 10 minutes, and then try again.
      2. Performing Secondary Air Injection Check repeatedly may cause damage to the secondary air injection system. If it is necessary to repeat the check, leave an interval of several minutes between System Check operations to prevent the system from overheating.
      3. When performing the Secondary Air Injection Check operation after the battery cable has been reconnected, wait for 7 minutes with the ignition switch turned to ON or the engine running.
      4. Turn the ignition switch off when the Secondary Air Injection Check operation finishes.

      OK:
      Air Pump Operation
      Emission Control Valve Operation
      Exhaust Gas Pulsation
      ON
      OFF
      Not detected
      ON
      ON
      Detected

      Text in Illustration 
      *a
      for Bank 1
      *b
      for Bank 2



NG
Go to step 11
OK


10.INSPECT EMISSION CONTROL VALVE SET (PRESSURE SENSOR)
  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the Techstream on.

  1. Enter the following menus: Powertrain / Engine and ECT / Data List / Air Pump Pressure (Absolute) and Air Pump2 Pressure (Absolute).

  1. Check the pressure displayed on the Techstream.

    Standard pressure:
    45.63 to 135 kPa (342 to 1013 mmHg)

    HINT:
    The Techstream displays the air pump pressure as absolute pressure.

    Result 
    Result
    Proceed to
    OK
    A
    NG (for Bank 1)
    B
    NG (for Bank 2)
    C



B
REPLACE EMISSION CONTROL VALVE SET (Click here)

C
REPLACE NO. 2 EMISSION CONTROL VALVE SET (Click here)
A

END 

11.INSPECT AIR TUBE FOR BLOCKAGE AND LEAKAGE
A221580E01
Text in Illustration 
*a
for Bank 1
*b
for Bank 2
  1. Check that the air tubes are securely connected to both the exhaust manifold and the emission control valve set.

  1. Inspect the air tube for blockages and damage.

    OK:
    No blockages in or damage to air tubes.



NG
REPLACE AIR TUBE
OK


12.INSPECT EMISSION CONTROL VALVE SET
  1. Inspect the emission control valve set (Click here).

  1. Inspect the No. 2 emission control valve set (Click here).
    Result 
    Result
    Proceed to
    OK
    A
    NG (for Bank 1)
    B
    NG (for Bank 2)
    C



B
REPLACE EMISSION CONTROL VALVE SET (Click here)

C
REPLACE NO. 2 EMISSION CONTROL VALVE SET (Click here)
A


13.INSPECT AIR INJECTION VSV RELAY (AI-VSV)
  1. Inspect the air injection VSV relay (AI-VSV) .



NG
REPLACE AIR INJECTION VSV RELAY (AI-VSV)
OK


14.CHECK AIR INJECTION VSV RELAY (AI-VSV) (POWER SOURCE)
A287417E01
  1. Remove the air injection VSV relay (AI-VSV) from the engine room relay block.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    1 (Air injection VSV relay (AI-VSV)) - Body ground
    Ignition switch ON
    11 to 14 V
    5 (Air injection VSV relay (AI-VSV)) - Body ground
    Always
    11 to 14 V

    Text in Illustration 
    *1
    Engine Room Relay Block
    *2
    Air Injection VSV Relay (AI-VSV)



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


15.CHECK HARNESS AND CONNECTOR (AIR INJECTION VSV RELAY (AI-VSV) - ECM)
  1. Remove the air injection VSV relay (AI-VSV) from the engine room relay block.

  1. Disconnect the B49 ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:

    Tester Connection
    Condition
    Specified Condition
    2 (Air injection VSV relay (AI-VSV)) - B49-21 (AIR1)
    Always
    Below 1 Ω
    2 (Air injection VSV relay (AI-VSV)) or B49-21 (AIR1) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


16.CHECK HARNESS AND CONNECTOR (NO. 2 EMISSION CONTROL VALVE SET - AIR INJECTION VSV RELAY (AI-VSV))
  1. Disconnect the B62 No. 2 emission control valve set connector.

  1. Remove the air injection VSV relay (AI-VSV).

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:

    Tester Connection
    Condition
    Specified Condition
    B62-5 (+BL) - 3 (Air injection VSV relay (AI-VSV))
    Always
    Below 1 Ω
    B62-1 (GNDL) - Body ground
    Always
    Below 1 Ω
    B62-5 (+BL) or 3 (Air injection VSV relay (AI-VSV)) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


17.INSPECT AIR INJECTION CONTROL DRIVER (POWER SOURCE OF AIR INJECTION CONTROL DRIVER)
A221587E11
  1. Disconnect the A38 and A37 air injection control driver connectors.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    A37-1 (E) - Body ground
    Always
    Below 1 Ω

  1. Turn the ignition switch to ON.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    A38-1 (BATT) - Body ground
    Always
    11 to 14 V (near battery voltage)
    A37-5 (+B) - Body ground
    Ignition switch ON
    11 to 14 V (near battery voltage)

Text in Illustration 
*a
Front view of wire harness connector
(to Air Injection Control Driver)


NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


18.CHECK HARNESS AND CONNECTOR (ECM - AIR INJECTION CONTROL DRIVER)
  1. Disconnect the B47 ECM connector.

  1. Disconnect the A37 air injection control driver connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:

    Tester Connection
    Condition
    Specified Condition
    B47-26 (AIRV) - A37-3 (SIV)
    Always
    Below 1 Ω
    B47-26 (AIRV) or A37-3 (SIV) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


19.PERFORM ACTIVE TEST USING TECHSTREAM


    A229922E40
  1. Disconnect the air injection control driver connector.

  1. Connect terminals DI and SIV of the wire harness connector for the air injection control driver.
    Text in Illustration 
    *1
    Air Injection Control Driver
    *2
    ECM
    *a
    Front view of wire harness connector
    (to Air Injection Control Driver)

  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to ON and turn the Techstream on.

  1. Enter the following menus: Powertrain / Engine and ECT / Utility / Secondary Air Injection Check / Manual Mode / AIR PUMP: ON, ASV 1: OPEN, ASV 2: OPEN.

    HINT:
    When Manual Mode is selected, the Techstream initialization (atmospheric pressure measurement) is performed automatically. The initialization takes 10 seconds. After the initialization, AIR PUMP and ASV operation can be selected.

  1. Start the engine.

  1. Perform the secondary air injection system forced operation while the engine is idling.

  1. Measure the voltage between the SIV and E terminals of the ECM connector when the secondary air injection system is ON and OFF.

  1. Turn the ignition switch off.

    NOTICE:
    1. Performing Secondary Air Injection Check repeatedly may cause damage to the secondary air injection system. If it is necessary to repeat the check, leave an interval of several minutes between System Check operations to prevent the system from overheating.
    2. When performing the Secondary Air Injection Check operation after the battery cable has been reconnected, wait for 7 minutes with the ignition switch turned to ON or the engine running.
    3. Turn the ignition switch off when the Secondary Air Injection Check operation finishes.


    Standard Voltage:

    Tester Connection
    Condition
    Specified Condition
    A37-3 (SIV) - A37-1 (E)
    AIR PUMP: ON, ASV: OPEN
    0.5 to 2 V
    A37-3 (SIV) - A37-1 (E)
    AIR PUMP: OFF, ASV: CLOSE
    11 to 14 V



    A229922E41
  1. Connect terminals DI and SIP of the wire harness connector for the air injection control driver.
    Text in Illustration 
    *1
    Air Injection Control Driver
    *2
    ECM
    *a
    Front view of wire harness connector
    (to Air Injection Control Driver)

  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to ON and turn the Techstream on.

  1. Enter the following menus: Powertrain / Engine and ECT / Utility / Secondary Air Injection Check / Manual Mode / AIR PUMP: ON, ASV 1: OPEN, ASV 2: OPEN.

    HINT:
    When Manual Mode is selected, the Techstream initialization (atmospheric pressure measurement) is performed automatically. The initialization takes 10 seconds. After the initialization, AIR PUMP and ASV operation can be selected.

  1. Start the engine.

  1. Perform the secondary air injection system forced operation while the engine is idling.

  1. Measure the voltage between the SIP and E terminals of the ECM connector when the secondary air injection system is ON and OFF.

  1. Turn the ignition switch off.

    NOTICE:
    1. Performing Secondary Air Injection Check repeatedly may cause damage to the secondary air injection system. If it is necessary to repeat the check, leave an interval of several minutes between System Check operations to prevent the system from overheating.
    2. When performing the Secondary Air Injection Check operation after the battery cable has been reconnected, wait for 7 minutes with the ignition switch turned to ON or the engine running.
    3. Turn the ignition switch off when the Secondary Air Injection Check operation finishes.


    Standard Voltage:

    Tester Connection
    Condition
    Specified Condition
    A37-4 (SIP) - A37-1 (E)
    AIR PUMP: ON, ASV: OPEN
    0.5 to 2 V
    A37-4 (SIP) - A37-1 (E)
    AIR PUMP: OFF, ASV: CLOSE
    11 to 14 V



NG
REPLACE ECM (Click here)
OK


20.REPLACE AIR INJECTION CONTROL DRIVER
  1. Replace the air injection control driver (Click here).


NEXT


21.CHECK WHETHER DTC OUTPUT RECURS (DTC P2440, P2441, P2442 AND/OR P2443)
  1. Start the engine and warm it up.

  1. Turn the ignition switch off.

  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the Techstream on.

  1. Clear the DTCs (if stored) (Click here).

  1. Enter the following menus: Powertrain / Engine and ECT / Utility / Secondary Air Injection Check / Automatic Mode.

  1. Start the engine after the Techstream initialization is finished.

  1. Perform the System Check operation by pressing Next.

  1. Perform the following to confirm the secondary air injection system pending DTCs: Press the Exit.

  1. Enter the following menus: Powertrain / Engine and ECT / Trouble codes.

  1. Read pending DTCs.

    OK:
    No pending DTC is output.

  1. Turn the ignition switch off.

    NOTICE:
    1. When performing the Secondary Air Injection Check operation after the battery cable has been reconnected, wait for 7 minutes with the ignition switch turned to ON or the engine running.
    2. Turn the ignition switch off when the Secondary Air Injection Check operation finishes.



NG
REPLACE ECM (Click here)
OK

END