Home › ENGINE › 1GR-FE ENGINE CONTROL SYSTEM › SFI SYSTEM

SFI SYSTEM > VC Output Circuit

for Preparation Click here


DESCRIPTION

The ECM constantly generates 5 V power from the battery voltage supplied to the +B (BATT) terminal to operate the microprocessor. The ECM also provides this power to the sensors through the VC output circuit.

A226795E03

When the VC circuit is short-circuited, the microprocessor in the ECM and sensors that are supplied power through the VC circuit are inactivated because the power is not supplied from the VC circuit. Under this condition, the system does not start up and the MIL does not illuminate even if the system malfunctions.

HINT:
Under normal conditions, the MIL is illuminated for several seconds when the ignition switch is first turned ON. The MIL goes off when the engine is started.


WIRING DIAGRAM


A287425E01


A287426E01


INSPECTION PROCEDURE

1.CHECK MIL
  1. Check that the Malfunction Indicator Lamp (MIL) lights up when turning the ignition switch to ON.

    OK:
    MIL lights up



NG
Go to step 2
OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE (Click here)  

2.CHECK CONNECTION BETWEEN TECHSTREAM AND ECM
  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to ON and turn the Techstream on.

  1. Check the communication between the Techstream and ECM.
    Result 
    Result
    Proceed to
    Communication is not possible
    A
    Communication is possible
    B



B
GO TO MIL CIRCUIT (Click here)
A


3.CHECK MIL (THROTTLE WITH MOTOR BODY ASSEMBLY)
  1. Disconnect the B14 throttle with motor body connector.

  1. Turn the ignition switch to ON.

  1. Check the MIL.
    Result 
    Result
    Proceed to
    MIL does not illuminate
    A
    MIL illuminates
    B

    HINT:
    Perform "Inspection After Repair" after replacing the throttle with motor body assembly (Click here).



B
REPLACE THROTTLE WITH MOTOR BODY ASSEMBLY (Click here)
A


4.CHECK MIL (ACCELERATOR PEDAL)
  1. Disconnect the A2 accelerator pedal connector.

  1. Turn the ignition switch to ON.

  1. Check the MIL.
    Result 
    Result
    Proceed to
    MIL does not illuminate
    A
    MIL illuminates
    B



B
REPLACE ACCELERATOR PEDAL (Click here)
A


5.CHECK MIL (CANISTER PUMP MODULE)
  1. Disconnect the L10 canister pump module connector.

  1. Turn the ignition switch to ON.

  1. Check the MIL.
    Result 
    Result
    Proceed to
    MIL does not illuminate
    A
    MIL illuminates
    B



B
REPLACE CANISTER (Click here)
A


6.CHECK MIL (VVT SENSOR FOR INTAKE SIDE OF BANK 1)
  1. Disconnect the B15 VVT sensor (for Intake Side of Bank 1) connector.

  1. Turn the ignition switch to ON.

  1. Check the MIL.
    Result 
    Result
    Proceed to
    MIL does not illuminate
    A
    MIL illuminates
    B



B
REPLACE VVT SENSOR (FOR INTAKE SIDE OF BANK 1) (Click here)
A


7.CHECK MIL (VVT SENSOR FOR EXHAUST SIDE OF BANK 1)
  1. Disconnect the B57 VVT sensor (for Exhaust Side of Bank 1) connector.

  1. Turn the ignition switch to ON.

  1. Check the MIL.
    Result 
    Result
    Proceed to
    MIL does not illuminate
    A
    MIL illuminates
    B



B
REPLACE VVT SENSOR (FOR EXHAUST SIDE OF BANK 1) (Click here)
A


8.CHECK MIL (VVT SENSOR FOR INTAKE SIDE OF BANK 2)
  1. Disconnect the B27 VVT sensor (for Intake Side of Bank 2) connector.

  1. Turn the ignition switch to ON.

  1. Check the MIL.
    Result 
    Result
    Proceed to
    MIL does not illuminate
    A
    MIL illuminates
    B



B
REPLACE VVT SENSOR (FOR INTAKE SIDE OF BANK 2) (Click here)
A


9.CHECK MIL (VVT SENSOR FOR EXHAUST SIDE OF BANK 2)
  1. Disconnect the B58 VVT sensor (for Exhaust Side of Bank 2) connector.

  1. Turn the ignition switch to ON.

  1. Check the MIL.
    Result 
    Result
    Proceed to
    MIL does not illuminate
    A
    MIL illuminates
    B



B
REPLACE VVT SENSOR (FOR EXHAUST SIDE OF BANK 2) (Click here)
A


10.CHECK MIL (POWER STEERING OIL PRESSURE SWITCH)
  1. Disconnect the B59 power steering oil pressure switch connector.

  1. Turn the ignition switch to ON.

  1. Check the MIL.
    Result 
    Result
    Proceed to
    MIL does not illuminate
    (w/ Secondary Air Injection System)
    A
    MIL does not illuminate
    (w/o Secondary Air Injection System)
    B
    MIL illuminates
    C



B
Go to step 13

C
REPLACE POWER STEERING OIL PRESSURE SWITCH (Click here)
A


11.CHECK MIL (EMISSION CONTROL VALVE SET)
  1. Disconnect the B61 emission control valve set connector.

  1. Turn the ignition switch to ON.

  1. Check the MIL.
    Result 
    Result
    Proceed to
    MIL does not illuminate
    A
    MIL illuminates
    B



B
REPLACE EMISSION CONTROL VALVE SET (Click here)
A


12.CHECK MIL (NO. 2 EMISSION CONTROL VALVE SET)
  1. Disconnect the B62 No. 2 emission control valve set connector.

  1. Turn the ignition switch to ON.

  1. Check the MIL.
    Result 
    Result
    Proceed to
    MIL does not illuminate
    A
    MIL illuminates
    B



B
REPLACE NO. 2 EMISSION CONTROL VALVE SET (Click here)
A


13.CHECK HARNESS AND CONNECTOR
  1. Disconnect the B14 throttle with motor body assembly connector.

  1. Disconnect the A2 accelerator pedal connector.

  1. Disconnect the L10 canister pump module connector.

  1. Disconnect the B15 VVT sensor (for Intake Side Bank 1) connector.

  1. Disconnect the B57 VVT sensor (for Exhaust Side Bank 1) connector.

  1. Disconnect the B27 VVT sensor (for Intake Side Bank 2) connector.

  1. Disconnect the B58 VVT sensor (for Exhaust Side Bank 2) connector.

  1. Disconnect the B59 power steering oil pressure switch connector.

  1. Disconnect the B61 emission control valve set connector (w/ Secondary Air Injection System).

  1. Disconnect the B62 No. 2 emission control valve set connector (w/ Secondary Air Injection System).

  1. Disconnect the B47, B48, B49 and E77 ECM connectors.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance (Check for Short):

    Tester Connection
    Condition
    Specified Condition
    B47-15 (VCV1) - Body ground
    Always
    10 kΩ or higher
    B47-16 (VCV2) - Body ground
    Always
    10 kΩ or higher
    E77-4 (VCPA) - Body ground
    Always
    10 kΩ or higher
    E77-2 (VCP2) - Body ground
    Always
    10 kΩ or higher
    B49-13 (VCTA) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE ECM (Click here)