Home › Engine / Hybrid System › 1GD-FTV (INTAKE / EXHAUST) › INTAKE MANIFOLD › 2019.02–2020.05
RM35X0E _51 Engine / Hybrid System _079307 1GD-FTV INTAKE / EXHAUST _0385720 INTAKE MANIFOLD A

1GD-FTV INTAKE / EXHAUST  INTAKE MANIFOLD  INSTALLATION  


CAUTION / NOTICE / HINT

NOTICE:
·

When replacing the parts in the following chart (A), replace the No. 1 injection pipe sub-assembly, No. 2 injection pipe sub-assembly and/or fuel inlet pipe sub-assembly with new ones.

Replaced Parts (A) Pipes Requiring New Replacement
·

Injector assembly (including shuffling the injector assemblies between the cylinders)


·

No. 1 injection pipe sub-assembly

·

No. 2 injection pipe sub-assembly


·

Supply pump assembly


·

Fuel inlet pipe sub-assembly


·

Common rail assembly

·

Cylinder block sub-assembly

·

Cylinder head sub-assembly

·

Timing chain case assembly


·

No. 1 injection pipe sub-assembly

·

No. 2 injection pipe sub-assembly

·

Fuel inlet pipe sub-assembly



·

After removing the No. 1 injection pipe sub-assembly, No. 2 injection pipe sub-assembly and/or fuel inlet pipe sub-assembly, clean them with a brush and compressed air.



PROCEDURE

Hide 17111 1.INSTALL INTAKE MANIFOLD

a.
A345106C01
2.75,0.385 2.979,0.385 2.979,0.385 3.24,0.781 true 2.573,0.281 2.885,0.438 0.313,0.156 10 true *a
*a Protrusion


Install a new gasket to the cylinder head sub-assembly.

HINT:

Install the gasket with the protrusion facing the rear side of the vehicle as shown in the illustration.



b.

Temporarily install the intake manifold with the 7 bolts and 2 nuts.


c.
A359574C02
0.073,2.542 0.385,2.74 0.313,0.198 10 true *B 0.063,0.052 0.375,0.25 0.313,0.198 10 true *A 0.406,1.615 0.719,1.813 0.313,0.198 10 true 8 1.208,1.594 1.521,1.792 0.313,0.198 10 true 3 1.979,1.604 2.292,1.802 0.313,0.198 10 true 7 2.781,1.625 3.094,1.823 0.313,0.198 10 true 5 3.115,0.083 3.365,0.281 0.25,0.198 10 true 2 2.479,0.042 2.792,0.24 0.313,0.198 10 true 4 1.99,0.26 2.302,0.458 0.313,0.198 10 true 9 0.688,0.052 1.021,0.219 0.333,0.167 10 true 6 0.354,0.229 0.563,0.479 0.208,0.25 10 true 1 0.375,2.76 0.583,3.01 0.208,0.25 10 true 1 0.729,2.708 1.063,2.875 0.333,0.167 10 true 6 2.01,2.948 2.323,3.146 0.313,0.198 10 true 9 2.49,2.698 2.802,2.896 0.313,0.198 10 true 4 3.125,2.656 3.375,2.854 0.25,0.198 10 true 2 2.865,4.292 3.177,4.49 0.313,0.198 10 true 5 2.083,4.302 2.396,4.5 0.313,0.198 10 true 7 1.25,4.302 1.563,4.5 0.313,0.198 10 true 3 0.458,4.313 0.771,4.51 0.313,0.198 10 true 8
*A w/ DPF
*B w/o DPF
V100135

Bolt
V100136

Nut


Tighten the 7 bolts and 2 nuts in the order shown in the illustration.

Torque:
23 N*m (235 kgf*cm, 17 ft.*lbf)


d.

w/o DPF:

Connect the vacuum hose assembly to the vacuum transmitting pipe sub-assembly.


e.

Connect the wire harness bracket with the bolt.

Torque:
18.6 N*m (190 kgf*cm, 14 ft.*lbf)


Hide 25804 2.INSTALL VACUUM CONTROL VALVE SET (w/ DPF)

a.

Install the vacuum control valve set with bolt to the intake manifold.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)


b.

Connect the 2 vacuum hoses to the vacuum control valve set and vacuum transmitting pipe sub-assembly.


c.

Connect the wire harness clamp and vacuum control valve set connector.


Hide 23770 3.INSTALL NO. 2 NOZZLE LEAKAGE PIPE ASSEMBLY

a.

Install the No. 2 nozzle leakage pipe assembly with the 2 bolts.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)


b.

Connect the No. 6 fuel hose to the No. 3 nozzle leakage pipe assembly and slide the clamp to secure the hoses.


c.

Install the No. 4 fuel hose and No. 5 fuel hose to the No. 2 nozzle leakage pipe assembly, and slide the 4 clamps to secure the hose.


Hide 23804C 4.INSTALL FUEL INLET PIPE SUB-ASSEMBLY

NOTICE:

When replacing the fuel supply pump assembly, it is necessary to replace the fuel inlet pipe sub-assembly, No. 1 injection pipe clamp and No. 2 injection pipe clamp with new ones.

Keep the fuel inlet pipe sub-assembly free of foreign matter.


a.

When replacing the No. 1 injection pipe clamp and No. 2 injection pipe clamp with new ones:

i.
A454527C02
2.073,1.844 2.51,1.844 true 2.177,1.24 2.615,1.24 true 2.552,1.74 2.865,1.896 0.313,0.156 10 false *1 2.667,1.135 2.979,1.292 0.313,0.156 10 false *2
*1 No. 1 Injection Pipe Clamp
*2 No. 2 Injection Pipe Clamp


Set a new No. 1 injection pipe clamp and No. 2 injection pipe clamp on the fuel inlet pipe sub-assembly.

NOTICE:
A454528C01
0.135,0.094 0.448,0.25 0.313,0.156 10 false *a
*a INCORRECT


When installing, do not pinch together the No. 1 injection pipe clamp or No. 2 injection pipe clamp.




b.

Temporarily install the fuel inlet pipe sub-assembly by turning its union nut by hand until it stops.


c.

When reusing the No. 1 injection pipe clamp and No. 2 injection pipe clamp:

i.

Install the No. 1 injection pipe clamp and No. 2 injection pipe clamp with the 2 bolts.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)



d.

When replacing the No. 1 injection pipe clamp and No. 2 injection pipe clamp with new ones:

i.
A454529

Pinch together the clamp while aligning it with the bolt installation hole of the No. 2 injection pipe clamp by hand, and then install the bolt to the intake manifold.

NOTICE:
·

Do not pinch together the No. 2 injection pipe clamp while tightening the bolt.

·

Pinch together the No. 2 injection pipe clamp by hand, and then install the bolt.

·

Do not forcibly align the position of the hole using the bolt.



Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)


ii.
A454530

Pinch together the clamp while aligning it with the bolt installation hole of the No. 1 injection pipe clamp by hand, and then install the bolt to the intake manifold.

NOTICE:
·

Do not pinch together the No. 1 injection pipe clamp while tightening the bolt.

·

Pinch together the No. 1 injection pipe clamp by hand, and then install the bolt.

·

Do not forcibly align the position of the hole using the bolt.



Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)



e.

With Common Rail Side Number Mark (24N):

i.
A439101C01
2.438,0.938 2.438,0.76 2.438,0.76 2.667,0.688 true 2.375,0.948 2.688,1.104 0.313,0.156 10 false *a
*a Number Mark (24N)


Make sure that the "24N" mark faces the common rail side of the fuel inlet pipe sub-assembly at the position shown in the illustration.

NOTICE:

Check for the number mark and tighten the parts to the specified tightening torque.



ii.
A412879C02
1.531,1.813 1.542,1.354 true 2.667,0.885 2.979,1.042 0.313,0.156 10 true *a 1.417,1.823 1.792,2 0.375,0.177 10 true SST
*a Torque Wrench Fulcrum Length


Using SST, tighten the fuel inlet pipe sub-assembly union nut on the common rail side sub-assembly.

SST
09245-11010  

Torque:
Specified tightening torque : 24 N*m (245 kgf*cm, 18 ft.*lbf)

HINT:
·

Calculate the torque wrench reading when changing the fulcrum length of the torque wrench.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

When using SST (fulcrum length of 50 mm (1.97 in.)) + torque wrench (fulcrum length of 180 mm (7.09 in.)): 18.8 N*m (192 kgf*cm, 14 ft.*lbf)




iii.
A329093C06
1.667,0.573 1.979,0.729 0.313,0.156 10 false *a
*a Torque Wrench Fulcrum Length


Using a 19 mm union nut wrench, tighten the fuel inlet pipe sub-assembly union nut on the fuel supply pump assembly side.

Torque:
Specified tightening torque : 28 N*m (286 kgf*cm, 21 ft.*lbf)

HINT:
·

Calculate the torque wrench reading when changing the fulcrum length of the torque wrench.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

When using a union nut wrench (fulcrum length of 30 mm (1.18 in.)) + torque wrench (fulcrum length of 180 mm (7.09 in.)): 24 N*m (245 kgf*cm, 18 ft.*lbf)





f.

Without Common Rail Side Number Mark (24N):

i.
A412879C02
1.531,1.813 1.542,1.354 true 2.667,0.885 2.979,1.042 0.313,0.156 10 true *a 1.417,1.823 1.792,2 0.375,0.177 10 true SST
*a Torque Wrench Fulcrum Length


Using SST, tighten the fuel inlet pipe sub-assembly union nut on the common rail side sub-assembly.

SST
09245-11010  

Torque:
Specified tightening torque : 40 N*m (408 kgf*cm, 30 ft.*lbf)

HINT:
·

Calculate the torque wrench reading when changing the fulcrum length of the torque wrench.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

When using SST (fulcrum length of 50 mm (1.97 in.)) + torque wrench (fulcrum length of 180 mm (7.09 in.)): 31 N*m (316 kgf*cm, 23 ft.*lbf)




ii.
A329093C06
1.667,0.573 1.979,0.729 0.313,0.156 10 false *a
*a Torque Wrench Fulcrum Length


Using a 19 mm union nut wrench, tighten the fuel inlet pipe sub-assembly union nut on the fuel supply pump assembly side.

Torque:
Specified tightening torque : 48 N*m (489 kgf*cm, 35 ft.*lbf)

HINT:
·

Calculate the torque wrench reading when changing the fulcrum length of the torque wrench.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

When using a union nut wrench (fulcrum length of 30 mm (1.18 in.)) + torque wrench (fulcrum length of 180 mm (7.09 in.)): 41 N*m (418 kgf*cm, 30 ft.*lbf)





Hide 17118 5.INSTALL MANIFOLD STAY

a.

Install the manifold stay with the 2 bolts.

Torque:
21 N*m (214 kgf*cm, 15 ft.*lbf)


b.

Install the wiring harness clamp bracket with the bolt.

Torque:
13 N*m (133 kgf*cm, 10 ft.*lbf)


Hide 23815D 6.INSTALL NO. 3 FUEL PIPE (w/ DPF or Pressurized Fuel Filter)

a.

Temporarily install the No. 3 fuel pipe and 2 new gaskets with the union bolt and supply pump hollow screw.

NOTICE:

Clean the union bolt and remove dirt completely.



b.

Tighten the union bolt and supply pump hollow screw.

Torque:
42 N*m (428 kgf*cm, 31 ft.*lbf)


c.
A339639C03
1.729,3.156 2.229,2.76 2.229,2.76 2.365,2.76 true 2.417,2.688 2.667,2.865 0.25,0.177 10 true *a 1.427,2.573 1.667,2.771 0.24,0.198 10 true *b 1.823,2.583 2.063,2.781 0.24,0.198 10 true *b
*a Paint Mark
*b 0 to 2 mm (0 to 0.0787 in.)


Install the fuel pipe clamp to the fuel filter assembly and No. 3 fuel pipe.

NOTICE:

Be careful that the fuel pipe clamp and No. 4 fuel pipe sub-assembly do not interfere with each other.


HINT:

Make sure the fuel pipe clamp is oriented as shown in the illustration.



Hide 23804D 7.INSTALL NO. 4 FUEL PIPE SUB-ASSEMBLY (w/ DPF)

a.

Temporarily install the No. 4 fuel pipe sub-assembly and 2 new gaskets with the 2 union bolts and bolt.


b.
A438132C02
2.531,3 2.729,3.198 0.198,0.198 10 true 1 3.021,3 3.208,3.188 0.188,0.188 10 true 2 1.448,1.552 1.646,1.75 0.198,0.198 10 true 3
V100136

Union Bolt
V100137

Bolt


Tighten the 2 union bolts and bolts in the order shown in the illustration.

Torque:
for union bolt : 42 N*m (428 kgf*cm, 31 ft.*lbf)
for bolt : 10 N*m (102 kgf*cm, 7 ft.*lbf)


c.

Connect the No. 4 fuel pipe sub-assembly to the No. 1 fuel pipe.

Click hereEngine / Hybrid System>1GD-FTV (FUEL)>FUEL SYSTEM>PRECAUTION


Hide 8.INSTALL WIRING HARNESS CLAMP BRACKET

a.

Install the wiring harness clamp bracket with the bolt.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)


b.

Attach the 2 wire harness clamps.


c.

Connect the diesel throttle body assembly connector and pre-stroke control valve connector.


Hide 23812D 9.INSTALL NO. 2 FUEL PIPE

a.

Connect the No. 2 fuel pipe and with the bolt.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)


Hide 11409 10.INSTALL ENGINE OIL LEVEL DIPSTICK GUIDE

a.

Apply a light coat of engine oil to a new O-ring.


b.

Install the O-ring to the engine oil level dipstick guide.


c.

Install the engine oil level dipstick guide with the bolt.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)


d.

Connect the vacuum hose to the intake manifold.


e.

Install the engine oil level dipstick.


f.

Attach the No. 2 fuel pipe clamp to the engine oil level dipstick guide.


Hide 25624 12.INSTALL EGR VALVE ADAPTER (w/o EGR Cooler)

a.
A412880

Install the EGR pipe stay to the EGR valve adapter with the 2 bolts.

Torque:
25 N*m (255 kgf*cm, 18 ft.*lbf)


b.

Temporarily install the EGR valve adapter to the intake manifold with the 4 bolts.


c.

Tighten the 4 bolts in the order shown in the illustration.

NOTICE:

Make sure to tighten the bolts in the correct order.


Torque:
21 N*m (214 kgf*cm, 15 ft.*lbf)

A408315C01
0.313,0.708 0.469,0.906 0.156,0.198 10 true 4 4.125,0.615 4.281,0.813 0.156,0.198 10 true 4 2.094,2.031 2.25,2.229 0.156,0.198 10 true 2 5.74,2.042 5.896,2.24 0.156,0.198 10 true 2 6.646,1.125 6.802,1.323 0.156,0.198 10 true 3 2.958,1.146 3.115,1.344 0.156,0.198 10 true 3 0.063,0.063 0.375,0.219 0.313,0.156 10 true *A 3.854,0.104 4.167,0.26 0.313,0.156 10 true *B 0.948,2.104 1.104,2.302 0.156,0.198 10 true 1 4.594,2.115 4.75,2.313 0.156,0.198 10 true 1
*A w/ EGR System without EGR Cooler *B w/o EGR System



d.

w/ EGR System:

Using an E8 "TORX" socket wrench, install 2 new stud bolts to the exhaust manifold.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)


e.

w/ EGR System:

Install 2 new gaskets and the EGR pipe with cooler sub-assembly or No. 1 EGR pipe sub-assembly to the exhaust manifold, electric EGR control valve assembly and vacuum transmitting pipe sub-assembly with the bolt and 4 new nuts.

Torque:
for bolt : 10 N*m (102 kgf*cm, 7 ft.*lbf)
for nut : 29 N*m (296 kgf*cm, 21 ft.*lbf)


f.

w/ EGR System:

i.

Connect the No. 4 water by-pass pipe sub-assembly to the intake manifold with the 2 bolts.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)


ii.

Connect the water hose to the EGR valve adapter, and slide the clamp to secure the hose.


iii.

Connect the No. 7 water by-pass hose to the EGR pipe stay, and slide the clamp to secure the hose.



g.

w/o EGR System:

i.

Connect the No. 4 water by-pass pipe sub-assembly to the intake manifold with the 2 bolts.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)


ii.

Connect the No. 7 water by-pass hose to the EGR pipe stay, and slide the clamp to secure the hose.



h.

w/ EGR System:

i.

Install the No. 3 water by-pass pipe sub-assembly to the EGR valve adapter with the 2 bolts.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)


ii.

Connect the No. 8 water by-pass hose to the No. 3 water by-pass pipe sub-assembly, and slide the clamp to secure the hose.



i.

w/o EGR System:

Install the No. 3 water by-pass pipe sub-assembly to the EGR valve adapter with the 2 bolts.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)


j.

Connect the No. 4 fuel hose to the No. 3 water by-pass pipe sub-assembly.


Hide 25800 13.INSTALL ELECTRIC EGR CONTROL VALVE ASSEMBLY (w/ EGR System without EGR Cooler)

Hide 25800 14.INSTALL EGR COOLER SUB-ASSEMBLY AND NO. 2 EGR VALVE ASSEMBLY WITH ELECTRIC EGR CONTROL VALVE ASSEMBLY (w/ EGR System with EGR Cooler)

Hide 15.CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

Hide 16. INITIALIZATION AFTER RECONNECTING BATTERY TERMINAL

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>WORK PROCEDURE

HINT:

When disconnecting and reconnecting the battery, there is an automatic learning function that completes learning when the respective system is used.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>AUTOMATIC LEARNING CHART


Hide 17.ADD ENGINE COOLANT