Home › Drivetrain › RC60J (MANUAL TRANSMISSION / TRANSAXLE) › MANUAL TRANSMISSION ASSEMBLY (for 7GR-FKS) › 2019.02–2019.06
RM35X0E _52 Drivetrain _078740 RC60J MANUAL TRANSMISSION / TRANSAXLE _0385768 MANUAL TRANSMISSION ASSEMBLY(for 7GR-FKS) A

RC60J MANUAL TRANSMISSION / TRANSAXLE  MANUAL TRANSMISSION ASSEMBLY(for 7GR-FKS)  REMOVAL  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed and installed, or replaced during manual transmission assembly removal/installation are shown below.

Necessary Procedures After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link
Disconnect cable from negative(-) battery terminal Memorize steering angle neutral point Parking assist monitor system (Click here)
Gas leaks from exhaust system Inspection after repair
·

Poor idle, etc.

·

Engine start function, etc.


(Click here)

CAUTION:
·
A350542

To prevent burns, do not touch the engine, exhaust pipe or other high temperature components while the engine is hot.

·
C313282C03
2.573,0.583 2.906,0.583 false 2.948,0.479 3.26,0.677 0.313,0.198 10 false *a
*a Object Exceeding Weight Limit of Transmission Jack


The manual transmission assembly is very heavy. Be sure to follow the procedure described in the repair manual, or the transmission jack may suddenly drop or a part may fall.



HINT:

When the cable is disconnected / reconnected to the battery terminal, systems temporarily stop operating. However, each system has a function that completes learning the first time the systems is used.

·

Learning completes when vehicle is driven

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link
Lane control system Drive the vehicle straight ahead at 15 km/h (10 mph) or more for 1 second or more. (Click here)
Pre-collision system

·

Learning completes when vehicle is operated normally

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link
Power slide door system Fully close the slide door by hand.
HINT:

Initialization is not necessary if the above procedures are performed while the slide door is closed.


(Click here)
Air conditioning system After the ignition switch is turned to ON, the servo motor standard position is recognized. -



PROCEDURE

Hide 1. PRECAUTION

NOTICE:

After turning the ignition switch is turned off, there may be a waiting time before disconnecting the negative (-) battery terminal.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>BEFORE DISCONNECTING BATTERY


Hide 28800 2.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

Hide 37100 4.REMOVE PROPELLER SHAFT WITH CENTER BEARING ASSEMBLY

Hide 28100 5.REMOVE STARTER ASSEMBLY

Hide 6.DRAIN MANUAL TRANSMISSION OIL

Hide 7.DRAIN CLUTCH FLUID

Hide 8.REMOVE CLUTCH ACCUMULATOR HEAT INSULATOR

Hide 31349 9.REMOVE CLUTCH CABLE HEAT INSULATOR

Hide 31482D 10.REMOVE CLUTCH RELEASE CYLINDER TO ACCUMULATOR TUBE

Hide 31490 11.REMOVE CLUTCH ACCUMULATOR ASSEMBLY

Hide 31470 12.REMOVE CLUTCH RELEASE CYLINDER ASSEMBLY

Hide 31482 13.REMOVE CLUTCH RELEASE CYLINDER TO FLEXIBLE HOSE TUBE

a.
C410221

Using a union nut wrench, disconnect the clutch release cylinder to flexible hose tube from the flexible hose.

HINT:

Use a container to catch the fluid.



b.

Remove the 3 bolts and clutch release cylinder to flexible hose tube from the manual transmission assembly and engine assembly.


Hide 33825 14.REMOVE TRANSMISSION CONTROL CABLE INSULATOR

a.
C410219

Remove the 3 bolts and transmission control cable insulator from the manual transmission assembly.


Hide 33820B 15.DISCONNECT TRANSMISSION CONTROL CABLE ASSEMBLY (for Transmission Assembly Side)

Hide 51446B 16.REMOVE NO. 2 ENGINE UNDER COVER BRACKET

a.

w/ Urea SCR System:

Disconnect the urea tube with heater assembly.

Click hereEngine / Hybrid System>1GD-FTV (ENGINE MECHANICAL)>ENGINE ASSEMBLY>REMOVAL


b.
C410213

Remove the 2 bolts and No. 2 engine under cover bracket from the frame.


Hide 58041C 17.REMOVE FRONT NO. 1 FLOOR HEAT INSULATOR SUB-ASSEMBLY

a.
C410235

Remove the 3 bolts and front No. 1 floor heat insulator sub-assembly from the body.


Hide 18.SUPPORT MANUAL TRANSMISSION ASSEMBLY

a.
C407267

Support the manual transmission assembly with a transmission jack.

NOTICE:
·

Make sure the high transmission jack attachment is centered on the safety stand.

·

Secure the part with a rope, attachment, etc.




Hide 57209B 19.REMOVE REAR ENGINE MOUNTING MEMBER SUB-ASSEMBLY

a.

w/ Cover:

Remove the step plate cover RH.

Click hereEngine / Hybrid System>7GR-FKS (ENGINE MECHANICAL)>ENGINE ASSEMBLY>REMOVAL


b.
C407269C01
0.177,0.906 0.333,1.104 0.156,0.198 10 false -
V100135

Bolt
V100136

Nut


Remove the 3 nuts from the rear engine mounting member sub-assembly.


c.

Remove the 4 bolts and rear engine mounting member sub-assembly from the body.


Hide 12380 20.REMOVE REAR ENGINE MOUNTING INSULATOR ASSEMBLY

a.
C407271

Remove the 4 bolts and rear engine mounting insulator assembly from the manual transmission assembly.


Hide 21.DISCONNECT WIRE HARNESS

a.
C410234C01
3.094,1.292 3.25,1.49 0.156,0.198 10 false -
V113147

Tilt Down


Tilt down the manual transmission assembly.

NOTICE:

Make sure that the cooling fan and fan shroud do not contact the engine assembly when tilting the manual transmission assembly.



b.

w/ Secondary Air Injection System (w/o Sensor):

Detach the 11 wire harness clamps.

C407273C01
3.604,0.938 3.865,1.177 0.26,0.24 10 false *A 5.167,1.365 5.385,1.552 0.219,0.188 10 true *B 1.292,1.896 1.51,2.073 0.219,0.177 10 true *C
*A w/ Secondary Air Injection System *B w/o Secondary Air Injection System
*C w/ Sensor - -
V100135

Bolt
V100136

Transmission Revolution Sensor Connector
V100137

Back-up Light Switch Assembly Connector - -



c.

w/o Secondary Air Injection System (w/ Sensor):

Disconnect the transmission revolution sensor connector and detach the 9 wire harness clamps.


d.

w/o Secondary Air Injection System (w/o Sensor):

Detach the 8 wire harness clamps.


e.

Disconnect the back-up light switch assembly connector.


f.

Remove the 3 bolts and disconnect the wire harness.


Hide 22.REMOVE MANUAL TRANSMISSION ASSEMBLY

a.

Using an engine lifter, jacks, etc., support the engine at an angle where the manual transmission assembly can be removed and in such a manner that the engine angle remains the same after the manual transmission assembly is removed.

NOTICE:

Make sure that the engine does not contact parts such as the body panel or fan shroud.



b.
C407275

Remove the 9 bolts and manual transmission assembly.

NOTICE:

As the manual transmission assembly is very heavy, be sure to support it securely.



Hide 33827 23.REMOVE NO. 3 TRANSMISSION CONTROL CABLE BRACKET

a.
C407276

Remove the 2 bolts and No. 3 transmission control cable bracket from the manual transmission assembly.


Hide 24.REMOVE WIRING HARNESS CLAMP BRACKET

a.

w/ Secondary Air Injection System (w/o Sensor):

Remove the 6 bolts and 6 wiring harness clamp brackets from the manual transmission assembly.

C407277C01
2.333,1.24 2.594,1.448 0.26,0.208 10 true *A 1.302,1.688 1.573,1.896 0.271,0.208 10 true *B
*A w/ Secondary Air Injection System *B w/ Sensor



b.

w/o Secondary Air Injection System (w/ Sensor):

Remove the 6 bolts and 6 wiring harness clamp brackets from the manual transmission assembly.


c.

w/o Secondary Air Injection System (w/o Sensor):

Remove the 5 bolts and 5 wiring harness clamp brackets from the manual transmission assembly.


Hide 33826A 25.REMOVE NO. 2 TRANSMISSION CONTROL CABLE BRACKET

a.
C410223

Remove the 2 bolts and No. 2 transmission control cable bracket from the manual transmission assembly.


Hide 33146 26.REMOVE EXTENSION HOUSING DUST(MTM) DEFLECTOR

a.
C407279C01
0.542,0.208 0.802,0.208 0.802,0.208 1.469,0.729 true 0.313,0.104 0.542,0.354 0.229,0.25 10 false *a
*a Protective Tape


Using a screwdriver, pry out the extension housing dust(MTM) deflector.

NOTICE:

Be careful not to damage the extension housing sub-assembly.


HINT:

Tape the screwdriver tip before use.