Home › Engine / Hybrid System › 1GD-FTV (INTAKE / EXHAUST) › EXHAUST MANIFOLD W/ TURBOCHARGER › from 2021.07
RM35X0E _51 Engine / Hybrid System _079307 1GD-FTV INTAKE / EXHAUST _0385721 EXHAUST MANIFOLD W/ TURBOCHARGER A

1GD-FTV INTAKE / EXHAUST  EXHAUST MANIFOLD W/ TURBOCHARGER  INSTALLATION  


PROCEDURE

Hide 1.INSTALL STUD BOLT

NOTICE:

If a stud bolt is deformed or its threads are damaged, replace it.


a.
A344970

Using an E10 "TORX" socket wrench, install the 3 stud bolts at the positions shown in the illustration.

Torque:
14.7 N*m (150 kgf*cm, 11 ft.*lbf)


b.
A344969

Using an E8 "TORX" socket wrench, install the 4 stud bolts at the positions shown in the illustration.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)


c.
A344968

Using an E5 "TORX" socket wrench, install the 4 stud bolts at the positions shown in the illustration.

Torque:
5.5 N*m (56 kgf*cm, 49 in.*lbf)


Hide 17275 2.INSTALL COMPRESSOR OUTLET ELBOW

a.

except Cold Area Specification Vehicles:

Install the hose clamp with the bolt.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)


b.

Install a new gasket.


c.

Install a new gasket and the compressor outlet elbow with the 2 nuts.

Torque:
21 N*m (214 kgf*cm, 15 ft.*lbf)


Hide 17274 3.INSTALL COMPRESSOR INLET ELBOW

a.

for Water Cooled Compressor Housing Turbocharger:

i.

Install a new gasket to the compressor inlet elbow.


ii.

Using an E8 "TORX" socket wrench, temporarily install the compressor inlet elbow with the stud bolt.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)



b.

except Water Cooled Compressor Housing Turbocharger:

i.

Using an E8 "TORX" socket wrench, temporarily install a new gasket and the compressor inlet elbow with the stud bolt.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)



c.

Install the compressor inlet elbow with the 2 nuts.

Torque:
21 N*m (214 kgf*cm, 15 ft.*lbf)


d.

Install the compressor inlet elbow stay with the 2 bolts.

Torque:
21 N*m (214 kgf*cm, 15 ft.*lbf)


Hide 16027 4.INSTALL NO. 1 TURBO WATER PIPE SUB-ASSEMBLY

a.

Install a new gasket.


b.

Temporarily install the No. 1 turbo water pipe sub-assembly with the bolt and 2 nuts.


c.

Tighten the bolt and 2 nuts.

Torque:
13 N*m (133 kgf*cm, 10 ft.*lbf)


d.

Connect the No. 1 turbo water hose and No. 2 turbo water hose to the No. 1 turbo water pipe sub-assembly and slide the 2 hose clips to secure the hoses.


Hide 15407 5.TEMPORARILY INSTALL TURBO OIL INLET PIPE SUB-ASSEMBLY

a.
A345118C01
2.448,1.802 2.76,1.958 0.313,0.156 10 true *b 0.729,1.813 1.042,1.969 0.313,0.156 10 true *a
*a NG
*b OK


Install a new gasket as shown in the illustration.

NOTICE:

Do not install the gasket upside down.



b.

Temporarily install the turbo oil inlet pipe sub-assembly with the 2 nuts.


Hide 17141 6.TEMPORARILY INSTALL EXHAUST MANIFOLD WITH TURBOCHARGER SUB-ASSEMBLY

a.

Install 2 new gaskets to the exhaust manifold and turbocharger sub-assembly.


b.

Temporarily install the exhaust manifold to turbocharger sub-assembly with 3 new nuts.


c.
A359584C01
1.083,1.885 1.219,1.99 1.219,1.99 1.427,1.99 false 0.979,4.344 1.115,4.448 1.115,4.448 1.323,4.448 false 0.063,0.042 0.375,0.198 0.313,0.156 10 true *A 0.115,2.219 0.427,2.375 0.313,0.156 10 false *B 1.438,1.875 1.75,2.031 0.313,0.156 10 false *1 1.344,4.333 1.667,4.49 0.323,0.156 10 false *1
*A w/ DPF
*B w/o DPF
*1 Collar
V100136

Engine Side


Temporarily install the exhaust manifold with turbocharger sub-assembly, 8 collars and 8 plate washers to the cylinder head sub-assembly with 8 new nuts.

NOTICE:

Make sure that the side of the collar with the smaller diameter faces the exhaust manifold.



d.

Install a new gasket on the union bolt side to turbo oil inlet pipe sub-assembly.


e.

Temporarily install the union bolt.


Hide 15474 7.INSTALL TURBO OIL OUTLET PIPE

a.

Install a new gasket to the turbo oil outlet pipe.

NOTICE:

The claws of the gasket must face the turbo oil outlet pipe.



b.

Install the turbo oil outlet pipe with the 2 bolts.

Torque:
12 N*m (122 kgf*cm, 9 ft.*lbf)


c.

Connect the turbo oil outlet hose to the turbo oil outlet pipe, turbo oil inlet pipe and slide the 2 hose clips to secure the hoses.


Hide 17293 8.TEMPORARILY INSTALL TURBOCHARGER STAY

a.

Temporarily install the turbocharger stay to the turbocharger sub-assembly with the 3 bolts and nut.


Hide 17141 9.TIGHTEN EXHAUST MANIFOLD WITH TURBOCHARGER SUB-ASSEMBLY

a.
A359724C01
0.063,0.031 0.375,0.188 0.313,0.156 10 true *A 0.135,2.25 0.448,2.406 0.313,0.156 10 false *B 0.885,2.469 1.042,2.667 0.156,0.198 10 true 6 1.344,2.458 1.5,2.656 0.156,0.198 10 true 1 1.917,2.49 2.073,2.688 0.156,0.198 10 true 2 2.25,2.479 2.406,2.677 0.156,0.198 10 true 7 2.521,3.844 2.677,4.042 0.156,0.198 10 true 8 2.177,3.844 2.333,4.042 0.156,0.198 10 true 3 1.781,3.813 1.938,4.01 0.156,0.198 10 true 4 0.49,3.833 0.646,4.031 0.156,0.198 10 true 5 2.479,1.323 2.635,1.521 0.156,0.198 10 true 8 2.188,1.333 2.344,1.531 0.156,0.198 10 true 3 1.76,1.323 1.917,1.521 0.156,0.198 10 true 4 0.625,1.375 0.781,1.573 0.156,0.198 10 true 5 0.885,0.021 1.042,0.219 0.156,0.198 10 true 6 1.344,0.021 1.5,0.219 0.156,0.198 10 true 1 1.917,0 2.073,0.198 0.156,0.198 10 true 2 2.229,0.031 2.385,0.229 0.156,0.198 10 true 7
*A w/ DPF
*B w/o DPF


Tighten the exhaust manifold with turbocharger sub-assembly to the cylinder head sub-assembly with the 8 nuts.

Torque:
40 N*m (408 kgf*cm, 30 ft.*lbf)

HINT:

Tighten the nuts in the order shown in the illustration.



b.

Tighten the turbocharger sub-assembly to the exhaust manifold with the 3 nuts.

Torque:
73 N*m (744 kgf*cm, 54 ft.*lbf)


c.

Tighten the 2 nuts and then union bolt of the turbo oil inlet pipe sub-assembly.

Torque:
for nut : 13 N*m (133 kgf*cm, 10 ft.*lbf)
for union bolt : 36 N*m (367 kgf*cm, 27 ft.*lbf)

NOTICE:

If the connecting part of the union bolt gasket is cracked, remove the connecting part.



Hide 17293 10.TIGHTEN TURBOCHARGER STAY

a.
A344955E01
1.833,0.188 2.042,0.417 0.208,0.229 10 true 1 2.771,0.448 2.979,0.677 0.208,0.229 10 true 2 1.531,2.969 1.74,3.198 0.208,0.229 10 true 3 0.365,1.99 0.573,2.219 0.208,0.229 10 true 4

Tighten the 3 bolts and nut of the turbocharger stay in the order shown in the illustration.

Torque:
24 N*m (245 kgf*cm, 18 ft.*lbf)


Hide 87101 11.INSTALL NO. 1 VISCOUS HEATER BRACKET SUB-ASSEMBLY (w/ Viscous Heater)

a.

Temporarily install the No. 1 viscous heater bracket sub-assembly with the 4 bolts.


b.
A360494E01
0.635,0.521 0.885,0.719 0.25,0.198 10 true 2 2.625,0.417 2.875,0.615 0.25,0.198 10 true 4 2.885,1.583 3.135,1.781 0.25,0.198 10 true 1 1.573,2.583 1.823,2.781 0.25,0.198 10 true 3

Tighten the 4 bolts of the No. 1 viscous heater bracket sub-assembly in the order shown in the illustration.

Torque:
24.5 N*m (250 kgf*cm, 18 ft.*lbf)


c.

Connect the wire harness with the bolt.

Torque:
13 N*m (133 kgf*cm, 10 ft.*lbf)


d.

Attach the clamp.


Hide 12.INSTALL WIRE HARNESS CLAMP BRACKET (for Manual Transmission)

a.

Connect the wire harness with the bolt.

Torque:
30 N*m (306 kgf*cm, 22 ft.*lbf)


Hide 13.INSTALL OIL COOLER TUBE BRACKET AND WIRE HARNESS CLAMP BRACKET (for Automatic Transmission)

a.

Connect the wire harness with the bolt.

Torque:
30 N*m (306 kgf*cm, 22 ft.*lbf)


b.

Connect the oil cooler tube bracket with the bolt.

Torque:
13.5 N*m (138 kgf*cm, 10 ft.*lbf)


Hide 25601 14.INSTALL NO. 1 EGR PIPE SUB-ASSEMBLY (w/ EGR System)

Hide 25601 15.INSTALL EGR PIPE WITH COOLER SUB-ASSEMBLY (for Laminated EGR Pre-cooler)

Hide 25617 16.INSTALL EGR HOLE COVER PLATE (w/o EGR System)

a.

Using an E8 "TORX" socket wrench, install 2 new stud bolts.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)


b.

Install a new gasket and the EGR hole cover plate with 2 new nuts.

Torque:
29 N*m (296 kgf*cm, 21 ft.*lbf)


Hide 16284 17.CONNECT TURBO WATER HOSE

a.

Connect the No. 1 turbo water hose and No. 2 turbo water hose to the water outlet sub-assembly and engine water pump assembly and slide the 2 hose clips to secure the hoses.

NOTICE:

The turbocharger sub-assembly may be damaged if the No. 1 turbo water hose and No. 2 turbo water hose are connected to the wrong locations.



Hide 16268 18.INSTALL NO. 1 WATER BY-PASS PIPE

Hide 19.CONNECT WATER BY-PASS HOSE (for Water Cooled Compressor Housing Turbocharger)

a.

Connect the No. 4 turbo water hose to the turbocharger sub-assembly and No. 1 turbo water pipe sub-assembly and slide the 2 hose clips to secure the hoses.


b.

Connect the No. 21 water by-pass hose to the turbocharger sub-assembly and No. 1 water by-pass pipe and slide the 2 hose clips to secure the hoses.


Hide 12261 20.INSTALL PCV HOSE (except Cold Area Specification Vehicles)

a.

Attach the clamp and install the PCV hose.


b.

Slide the 2 hose clips to secure the hoses.


Hide 12229 21.INSTALL PCV PIPE (for Cold Area Specification Vehicles)

a.

Connect the PCV pipe to the compressor inlet elbow and cylinder head cover sub-assembly and slide the 2 hose clips to secure the hoses.


b.

for Air Cooled Type Intercooler:

Install the PCV pipe to the compressor outlet elbow with the bolt.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)


c.

for Water Cooled Type Intercooler:

Install the PCV pipe to the compressor outlet elbow with the 2 bolts.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)


d.

Connect the No. 19 water by-pass hose to the compressor inlet elbow and slide the hose clip to secure the hoses.


e.

Install the No. 20 water by-pass hose to the PCV pipe and No. 1 water by-pass pipe, and slide the 2 hose clips to secure the hoses.


Hide 16279 22.INSTALL NO. 3 WATER BY-PASS PIPE

a.

Connect the 2 water hoses to the oil cooler assembly and No. 2 water by-pass pipe sub-assembly, and slide the 2 hose clips to secure the hoses.


b.

Install the No. 3 water by-pass pipe with the bolt.

Torque:
21 N*m (214 kgf*cm, 15 ft.*lbf)


c.

for Cold Area Specification Vehicles:

Install the water hose to the compressor inlet elbow and No. 3 water by-pass pipe, and slide the 2 hose clips to secure the hoses.


Hide 87120G 23.INSTALL VISCOUS HEATER WITH MAGNET CLUTCH ASSEMBLY (w/ Viscous Heater)

Hide 24.INSTALL WATER HOSE SUB-ASSEMBLY (w/ Viscous Heater)

Hide 17701 25.INSTALL AIR CLEANER CASE SUB-ASSEMBLY

a.
A438148C01
2.24,4.396 2.385,4.406 2.385,4.406 2.677,4.125 true 1.99,3.625 1.99,3.438 1.99,3.438 2.24,3.135 true 1.865,3.615 2.083,3.813 0.219,0.198 10 true *a 2,4.292 2.208,4.49 0.208,0.198 10 true *b
*a Pin
*b Duct


Install the air cleaner case sub-assembly with the 3 bolts.

Torque:
5.0 N*m (51 kgf*cm, 44 in.*lbf)

HINT:

Make sure to attach the pin and duct of the air cleaner case sub-assembly.



Hide 17801 26.INSTALL AIR CLEANER FILTER ELEMENT SUB-ASSEMBLY

a.

Install the air cleaner filter element sub-assembly to the air cleaner case sub-assembly.


Hide 17705 27.INSTALL AIR CLEANER CAP SUB-ASSEMBLY WITH AIR CLEANER HOSE

a.

Attach the 2 guides to install the air cleaner cap sub-assembly with air cleaner hose to the air cleaner case sub-assembly.


b.

Attach the 2 air cleaner cap clamps.


c.

Tighten the hose clamp.

Torque:
4.0 N*m (41 kgf*cm, 35 in.*lbf)


d.

Connect the mass air flow meter connector.


e.

Attach the wire harness clamp.


Hide 16515A 29.CONNECT INTERCOOLER COOLING WATER PIPE ASSEMBLY (for Water Cooled Type Intercooler)

Hide 161B0 30.INSTALL ELECTRIC WATER PUMP ASSEMBLY (for Water Cooled Type Intercooler)

Hide 165A0 31.INSTALL NO. 1 INTERCOOLER COOLING WATER HOSE ASSEMBLY (for Water Cooled Type Intercooler)

Hide 16552C 32.INSTALL NO. 2 INTERCOOLER COOLING WATER HOSE (for Water Cooled Type Intercooler)

Hide 16571C 33.INSTALL NO. 1 RADIATOR HOSE

Hide 16470 34.INSTALL RADIATOR RESERVE TANK ASSEMBLY

Hide 16640 35.INSTALL INTERCOOLER RESERVE TANK ASSEMBLY (for Water Cooled Type Intercooler)

Hide 44360 36.CONNECT VANE PUMP OIL RESERVOIR ASSEMBLY

Hide 17751 37.INSTALL NO. 1 AIR CLEANER INLET

Hide 53106B 38.INSTALL RADIATOR COVER SUB-ASSEMBLY

Hide 17303T 39.INSTALL AIR PIPE SUB-ASSEMBLY (for Air Cooled Type Intercooler)

Hide 25761B 40.CONNECT NO. 1 VACUUM TRANSMITTING HOSE (for Air Cooled Type Intercooler)

Hide 17030 41.INSTALL AIR HOSE ASSEMBLY (for Air Cooled Type Intercooler)

Hide 17940D 42.INSTALL INTERCOOLER ASSEMBLY (for Water Cooled Type Intercooler)

Hide 17291 44.INSTALL TURBINE OUTLET ELBOW (w/o EGR Cooler)

Hide 45.INSTALL NO. 2 EXHAUST PIPE SUPPORT STAY (w/o EGR Cooler)

Hide 17271 46.INSTALL NO. 1 TURBO INSULATOR (w/o EGR Cooler)

Hide 17167 47.INSTALL NO. 1 EXHAUST MANIFOLD HEAT INSULATOR (w/o EGR Cooler)

Hide 49.ADD ENGINE COOLANT

Hide 50.ADD ENGINE COOLANT (for Water Cooled Type Intercooler)

Hide 51405A 56.INSTALL NO. 1 ENGINE UNDER COVER ASSEMBLY

Hide 52618 57.INSTALL LOWER FRONT BUMPER ABSORBER

Hide 51406A 58.INSTALL NO. 2 ENGINE UNDER COVER SUB-ASSEMBLY (w/ No. 2 Engine Under Cover Sub-assembly)

Hide 12601B 59.INSTALL NO. 1 ENGINE COVER SUB-ASSEMBLY