Home › Engine / Hybrid System › 1GD-FTV (EMISSION CONTROL) › MONOLITHIC CONVERTER (w/ DPF) › from 2020.05
RM35X0E _51 Engine / Hybrid System _079220 1GD-FTV EMISSION CONTROL _0384163 MONOLITHIC CONVERTER(w/ DPF) A

1GD-FTV EMISSION CONTROL  MONOLITHIC CONVERTER(w/ DPF)  INSTALLATION  


PROCEDURE

Hide 89463C 1.INSTALL NO. 1 NITROGEN OXIDES SENSOR

Hide 25051 2.INSTALL EXHAUST MANIFOLD CONVERTER SUB-ASSEMBLY

a.

Set a new gasket and the exhaust manifold converter sub-assembly to the turbocharger sub-assembly.


b.

Temporarily install the exhaust pipe support stay to the cylinder block sub-assembly and exhaust manifold converter sub-assembly with the 3 bolts.


c.
A344468C01
2.427,0.646 2.25,0.406 2.25,0.406 2.167,0.406 true 2.688,1.354 2.688,1.656 true 1.99,0.313 2.177,0.469 0.188,0.156 10 false *1 2.281,1.229 2.469,1.396 0.188,0.167 10 false *2 2.917,1.229 3.104,1.406 0.188,0.177 10 false *3 2.635,1.677 2.833,1.844 0.198,0.167 10 false *4 0.646,1.917 0.958,2.073 0.313,0.156 10 true 90°
*1 Exhaust Pipe Clamp
*2 Exhaust Manifold Converter Sub-assembly
*3 Turbocharger Sub-assembly
*4 Gasket


Install a new exhaust pipe clamp to the exhaust manifold converter sub-assembly with a new nut.

Torque:
18 N*m (184 kgf*cm, 13 ft.*lbf)


d.
A456473

Temporarily install the exhaust pipe support stay to the exhaust manifold converter sub-assembly with the bolt.

Torque:
8.5 N*m (87 kgf*cm, 75 in.*lbf)


e.
A440905N01
2.135,1.458 2.292,1.656 0.156,0.198 10 true 1 1.427,1.833 1.583,2.031 0.156,0.198 10 true 2 1.365,0.438 1.51,0.594 0.146,0.156 10 true 3

Tighten the 3 bolts and install the exhaust pipe support stay to the cylinder block sub-assembly and exhaust manifold converter sub-assembly in the order shown in the illustration.

Torque:
38 N*m (387 kgf*cm, 28 ft.*lbf)


Hide 17118 3.INSTALL NO. 2 EXHAUST PIPE SUPPORT STAY

a.

Temporarily install the No. 2 exhaust pipe support stay to the cylinder block sub-assembly and exhaust manifold converter sub-assembly with the bolt and 2 new nuts.


b.
A456472

Temporarily install the No. 2 exhaust pipe support stay to the exhaust manifold converter sub-assembly with the bolt.

Torque:
8.5 N*m (87 kgf*cm, 75 in.*lbf)


c.
A440904N01
1.104,1.073 1.229,1.24 0.125,0.167 10 true 1 1.365,1.99 1.5,2.146 0.135,0.156 10 true 2 1.167,1.302 1.292,1.469 0.125,0.167 10 true 3

Tighten the bolt and 2 nuts and install the No. 2 exhaust pipe support stay to the cylinder block sub-assembly and exhaust manifold converter sub-assembly in the order shown in the illustration.

Torque:
38 N*m (387 kgf*cm, 28 ft.*lbf)


Hide 89463C 4.CONNECT NO. 1 NITROGEN OXIDES SENSOR

a.

for Air Cooled Type Intercooler (w/ Exhaust Gas Temperature Sensor for EGR):

i.

Install the sensor bracket to the cylinder head sub-assembly with the bolt.

Torque:
13 N*m (133 kgf*cm, 10 ft.*lbf)


ii.

Attach the 4 clamps and connect the No. 1 nitrogen oxides sensor.


iii.

Install the 2 bolts.

Torque:
13 N*m (133 kgf*cm, 10 ft.*lbf)


iv.

Connect the connector to the No. 1 nitrogen oxides sensor.



b.

for Water Cooled Type Intercooler:

i.

Install the sensor bracket to the cylinder head sub-assembly with the bolt.

Torque:
13 N*m (133 kgf*cm, 10 ft.*lbf)


ii.

Attach the 5 clamps and connect the No. 1 nitrogen oxides sensor.


iii.

Install the 2 bolts.

Torque:
13 N*m (133 kgf*cm, 10 ft.*lbf)


iv.

Connect the connector to the No. 1 nitrogen oxides sensor.



c.

Install the outer cowl top panel sub-assembly.

Click hereEngine / Hybrid System>1GD-FTV (ENGINE MECHANICAL)>ENGINE ASSEMBLY>INSTALLATION


d.

Install the windshield wiper motor assembly.

Click hereVehicle Exterior>WIPER / WASHER>FRONT WIPER MOTOR>INSTALLATION


Hide 17271 5.INSTALL NO. 1 TURBO INSULATOR

a.

Install the No. 1 turbo insulator to the exhaust manifold and turbocharger sub-assembly with the 3 bolts.

Torque:
12 N*m (122 kgf*cm, 9 ft.*lbf)


Hide 17167 6.INSTALL NO. 1 EXHAUST MANIFOLD HEAT INSULATOR

a.

Install the No. 1 exhaust manifold heat insulator to the exhaust manifold with the 3 bolts.

Torque:
12 N*m (122 kgf*cm, 9 ft.*lbf)


Hide 89467B 7.INSTALL AIR FUEL RATIO SENSOR

for Air Cooled Type Intercooler (w/o Exhaust Gas Temperature Sensor for EGR):

Click hereEngine / Hybrid System>1GD-FTV (ENGINE CONTROL)>AIR FUEL RATIO SENSOR>INSTALLATION

Hide 8.CONNECT INTERMEDIATE SHAFT ASSEMBLY (for RHD)

Hide 12631A 9.INSTALL ENGINE COVER BRACKET (for Air Cooled Type Intercooler)

a.

Install the engine cover bracket to the cylinder head sub-assembly with the 2 bolts.

Torque:
21 N*m (214 kgf*cm, 15 ft.*lbf)


b.

Attach the 2 clamps and connect the engine wire to the cylinder head sub-assembly.


Hide 17945 10.INSTALL INTERCOOLER SUPPORT BRACKET (for Water Cooled Type Intercooler)

a.

Install the intercooler support bracket to the cylinder head sub-assembly with the 2 bolts.

Torque:
21 N*m (214 kgf*cm, 15 ft.*lbf)


b.

Attach the clamp and connect the engine wire to the intercooler support bracket with the 2 bolts.

Torque:
13 N*m (133 kgf*cm, 10 ft.*lbf)


Hide 17578B 11.INSTALL PIPE CLAMP

a.

Install the pipe clamp to the engine cover bracket with the 3 bolts.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)


Hide 25734 12.TEMPORARILY INSTALL NO. 2 VACUUM PIPE

a.

Install a new clamp to the pipe clamp.


b.

Temporarily install the No. 2 vacuum pipe to the exhaust manifold converter sub-assembly.


Hide 25733A 13.TEMPORARILY INSTALL NO. 1 VACUUM PIPE

a.

Temporarily install the No. 1 vacuum pipe to the exhaust manifold converter sub-assembly.


b.

Install a new clamp to the No. 1 vacuum pipe and No. 2 vacuum pipe with the nut.

Torque:
6.0 N*m (61 kgf*cm, 53 in.*lbf)


Hide 25734 14.TIGHTEN NO. 2 VACUUM PIPE

a.
A329093C01
1.667,0.573 1.979,0.729 0.313,0.156 10 false *a
*a Torque Wrench Fulcrum Length


Using a 17 mm union nut wrench, tighten the No. 2 vacuum pipe.

Torque:

Specified tightening torque

48 N*m (489 kgf*cm, 35 ft.*lbf)


HINT:
·

Calculate the torque wrench reading when changing the fulcrum length of the torque wrench.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

When using a union nut wrench (fulcrum length of 30 mm (1.18 in.)) + torque wrench (fulcrum length of 255 mm (10.0 in.)): 42.9 N*m (437 kgf*cm, 32 ft.*lbf)




Hide 25733A 15.TIGHTEN NO. 1 VACUUM PIPE

a.
A329093C01
1.667,0.573 1.979,0.729 0.313,0.156 10 false *a
*a Torque Wrench Fulcrum Length


Using a 17 mm union nut wrench, tighten the No. 1 vacuum pipe.

Torque:

Specified tightening torque

48 N*m (489 kgf*cm, 35 ft.*lbf)


HINT:
·

Calculate the torque wrench reading when changing the fulcrum length of the torque wrench.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

When using a union nut wrench (fulcrum length of 30 mm (1.18 in.)) + torque wrench (fulcrum length of 255 mm (10.0 in.)): 42.9 N*m (437 kgf*cm, 32 ft.*lbf)




Hide 17801 19.INSTALL AIR CLEANER FILTER ELEMENT SUB-ASSEMBLY

Hide 17705 20.INSTALL AIR CLEANER CAP SUB-ASSEMBLY WITH AIR CLEANER HOSE

Hide 17751 21.INSTALL NO. 1 AIR CLEANER INLET

Hide 17168 22.INSTALL NO. 2 EXHAUST MANIFOLD HEAT INSULATOR

Hide 17410 23.INSTALL FRONT EXHAUST PIPE ASSEMBLY