Home › BRAKE › BRAKE CONTROL › ELECTRONICALLY CONTROLLED BRAKE SYSTEM

DTC    C1341/62    Front Hydraulic System RH Malfunction

DTC    C1342/63    Front Hydraulic System LH Malfunction

DTC    C1343/64    Rear Hydraulic System RH Malfunction

DTC    C1344/65    Rear Hydraulic System LH Malfunction

for Preparation Click here


DESCRIPTION

The skid control ECU controls braking force according to the hybrid control system regenerative braking force and inputs the hydraulic pressure necessary for operating each wheel cylinder according to the wheel cylinder pressure sensor.
DTCs may be stored if one of the following occurs:
  1. Brake fluid leaks.
  2. Wheel cylinder vibrates due to uneven wear of a brake rotor.
  3. Foreign matter enters solenoid valve.
  4. Line pressure drops during air bleeding.
  5. Brake pad is replaced.
  6. Rotor is replaced.

DTC Code
INF Code
DTC Detection Condition
Trouble Area
C1341/62
551
552
Decrease in FR wheel hydraulic pressure control.
  1. Fluid leak
  2. Brake actuator assembly
↑
553
There is a malfunction or leak in the FR wheel pressure increase control valve.
  1. Fluid leak
  2. Disc rotor
  3. Brake actuator assembly
↑
554
555
There is a malfunction or leak in the FR wheel pressure decrease control valve.
↑
C1342/63
561
562
Decrease in FL wheel hydraulic pressure control.
  1. Fluid leak
  2. Brake actuator assembly
↑
563
There is a malfunction or leak in the FL wheel pressure increase control valve.
  1. Fluid leak
  2. Disc rotor
  3. Brake actuator assembly
↑
564
565
There is a malfunction or leak in the FL wheel pressure decrease control valve.
↑
C1343/64
571
572
Decrease in RR wheel hydraulic pressure control.
  1. Fluid leak
  2. Brake actuator assembly
↑
573
There is a malfunction or leak in the RR wheel pressure increase control valve.
  1. Fluid leak
  2. Disc rotor
  3. Brake actuator assembly
↑
574
575
There is a malfunction or leak in the RR wheel pressure decrease control valve.
↑
C1344/65
581
582
Decrease in RL wheel hydraulic pressure control.
  1. Fluid leak
  2. Brake actuator assembly
↑
583
There is a malfunction or leak in the RL wheel pressure increase control valve.
  1. Fluid leak
  2. Disc rotor
  3. Brake actuator assembly
↑
584
585
There is a malfunction or leak in the RL wheel pressure decrease control valve.
↑

WIRING DIAGRAM

Refer to DTCs C1246/46, C1281/81 and C1364/61 .

INSPECTION PROCEDURE

NOTICE:
When replacing the brake actuator assembly, perform initialization and calibration of the linear solenoid valve (Click here).

HINT:
When C1364/61 is output together with C1341/62, C1342/63, C1343/64 and/or C1344/65, inspect and repair the trouble areas indicated by C1364/61 first (Click here).

1.CHECK FOR FLUID LEAK
  1. Check that there is no fluid leakage in the brake line between the brake actuator and the wheel cylinder which is indicated by DTCs.

  1. Check that the brake is not dragging.

    OK:
    There is no fluid leakage or dragging.



NG
REPAIR OR REPLACE APPLICABLE PART
OK


2.PERFORM AIR BLEEDING
  1. Bleed the air from the front and rear brake systems (Click here).


NEXT


3.RECONFIRM DTC
  1. Clear the DTCs (Click here).

  1. Perform a road test under malfunction conditions recreated based on the Freeze Frame Data or customer problem analysis.

  1. Check if the same DTC is recorded (Click here).

    Result:

    Result
    Proceed to
    DTCs (C1341/62, C1342/63, C1343/64 and/or C1344/65) are output
    A
    DTCs (C1341/62, C1342/63, C1343/64 and C1344/65) are not output
    B

    HINT:
    DTCs may be stored if foreign matter or air enters the solenoid valves.



B
END
A


4.CHECK HARNESS AND CONNECTOR (SKID CONTROL ECU - BODY GROUND)


    C174058E01
  1. Turn the power switch off.

  1. Make sure that there is no looseness at the locking part and the connecting part of the connectors.

  1. Disconnect the skid control ECU connectors and the brake actuator connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester connection
    Condition
    Specified condition
    A46-8 (E) - Body ground
    Always
    10 kΩ or higher
    A46-9 (VCM1) - Body ground
    Always
    10 kΩ or higher
    A46-18 (PRL) - Body ground
    Always
    10 kΩ or higher
    A46-20 (SG1) - Body ground
    Always
    10 kΩ or higher
    A46-21 (PACC) - Body ground
    Always
    10 kΩ or higher
    A46-23 (PFR) - Body ground
    Always
    10 kΩ or higher
    A46-30 (PMC1) - Body ground
    Always
    10 kΩ or higher
    A46-31 (PCK1) - Body ground
    Always
    10 kΩ or higher
    A45-12 (SG2) - Body ground
    Always
    10 kΩ or higher
    A45-14 (VCM2) - Body ground
    Always
    10 kΩ or higher
    A45-21 (PCK2) - Body ground
    Always
    10 kΩ or higher
    A45-23 (PFL) - Body ground
    Always
    10 kΩ or higher
    A45-27 (PMC2) - Body ground
    Always
    10 kΩ or higher
    A45-29 (E2) - Body ground
    Always
    10 kΩ or higher
    A45-31 (PRR) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


5.READ VALUE USING TECHSTREAM (WHEEL CYLINDER PRESSURE SENSOR)
  1. Reconnect the skid control ECU connectors and the brake actuator connector.

  1. Connect the pedal effort gauge (Click here).

  1. Install the hydro LSPV gauge and bleed air (Click here).

SST
09709-29018  
  1. Connect the Techstream to the DLC3.

  1. Turn the power switch on (IG).

  1. Select the Data List mode on the Techstream (Click here).

    ABS / VSC / TRAC: 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    FR W/C Sensor
    FR wheel cylinder pressure sensor / min.: 0 V, max.: 5 V
    When brake pedal is released:
    0.3 to 0.9 V
    -
    FL W/C Sensor
    FL wheel cylinder pressure sensor / min.: 0 V, max.: 5 V
    When brake pedal is released:
    0.3 to 0.9 V
    -
    RR W/C Sensor
    RR wheel cylinder pressure sensor / min.: 0 V, max.: 5 V
    When brake pedal is released:
    0.3 to 0.9 V
    -
    RL W/C Sensor
    RL wheel cylinder pressure sensor / min.: 0 V, max.: 5 V
    When brake pedal is released:
    0.3 to 0.9 V
    -

  1. Check the output value of the wheel cylinder pressure sensor at each hydraulic pressure level during the electronically controlled brake system control.

    Standard voltage:
    for front wheel cylinder pressure sensor:

    Hydraulic Pressure
    MPa (kgf/cm2, psi)
    FR W/C Sensor
    (Data List Display)
    FL W/C Sensor
    (Data List Display)
    2.4 (24.5, 348)
    0.80 to 1.20 V
    0.80 to 1.20 V
    5.4 (54.1, 783)
    1.40 to 1.80 V
    1.40 to 1.80 V
    6.5 (66.3, 943)
    1.60 to 2.00 V
    1.60 to 2.00 V
    7.1 (72.4, 1030)
    1.75 to 2.15 V
    1.75 to 2.15 V
    for rear wheel cylinder pressure sensor:

    Hydraulic Pressure
    MPa (kgf/cm2, psi)
    RR W/C Sensor
    (Data List Display)
    RL W/C Sensor
    (Data List Display)
    2.4 (24.5, 348)
    0.80 to 1.20 V
    0.80 to 1.20 V
    5.0 (51.0, 725)
    1.30 to 1.70 V
    1.30 to 1.70 V



NG
REPLACE BRAKE ACTUATOR ASSEMBLY (Click here)
OK


6.CHECK BRAKE DISC
  1. Turn the power switch off.

  1. Disconnect the brake pedal stroke sensor connector.

  1. Perform a road test according to Freeze Frame Data or customer problem analysis. Check the brake line pressure vibration caused due to uneven wear of the disc according to brake pedal vibration.

    OK:
    Brake pedal does not vibrate during braking.

    HINT:
    1. The brake pedal does not kick back due to wheel cylinder piston vibration during electronically controlled brake system control.
    2. If the brake pedal stroke sensor connector is disconnected, the fail safe function will prohibit electronically controlled brake system control.
    3. The Active Test does not prohibit electronically controlled brake system control when the vehicle is running, so disconnect the stroke sensor connector before continuing with inspection.
    4. Disc wear can be checked by measuring the disc thickness (Click here for front, or Click here for rear).



NG
REPLACE BRAKE DISC
OK


7.RECONFIRM DTC
  1. Reconnect the brake pedal stroke sensor connector.

  1. Clear the DTCs (Click here).

  1. Perform a road test under the same malfunction conditions recreated based on the Freeze Frame Data or customer problem analysis.

  1. Check if the same DTC is recorded (Click here).

    Result:

    Result
    Proceed to
    DTCs (C1341/62, C1342/63, C1343/64 and C1344/65) are not output
    A
    DTCs (C1341/62, C1342/63, C1343/64 and/or C1344/65) are output
    B



B
REPLACE BRAKE ACTUATOR ASSEMBLY (Click here)
A

CHECK FOR INTERMITTENT PROBLEMS (SYMPTOM SIMULATION) (Click here)