Home › SUSPENSION & AXLE › AXLE › AXLE SYSTEM

DTC    C1348    Different Diameter Tire Malfunction

for Preparation Click here


DESCRIPTION

The skid control ECU measures the speed of each wheel by receiving signals from the speed sensors. These signals are used to recognize that all 4 wheels are operating properly. Therefore, all wheel signals must be equal.

DTC No.
DTC Detection Condition
Trouble Area
C1348
Difference in the size between the front and rear tires is detected
  1. Tire size
  2. Tire pressure
  3. Speed sensor circuit
  4. Skid control ECU

WIRING DIAGRAM


Wiring Diagram 
Circuit
Proceed to
Front circuit
Click here
Rear circuit
Click here

INSPECTION PROCEDURE

1.CHECK DTC
  1. Check the output DTC (axle system, electronically controlled brake system, CAN communication system).

    Result:

    Result
    Proceed to
    DTC C1348 only is output
    A
    CAN communication DTC is output
    B
    Electronically Controlled Brake system DTC is output
    C

    HINT:
    When DTCs indicating a CAN communication system malfunction are output, repair the CAN communication system before repairing each corresponding sensor.



B
REPAIR CIRCUITS INDICATED BY OUTPUT DTCS (Click here)

C
REPAIR CIRCUITS INDICATED BY OUTPUT DTCS (Click here)
A


2.CHECK TIRE CONDITION
  1. Check the size and condition of all 4 tires (Click here).

    HINT:
    This DTC is output when tire deformation or a difference in tire sizes is detected.

    OK:
    The diameter and air pressure of all 4 tires are the same.



NG
REPLACE TIRES SO THAT ALL 4 TIRE ARE SAME IN SIZE, OR ADJUST TIRE PRESSURE (Click here)
OK


3.READ VALUE USING TECHSTREAM (FRONT AND REAR SPEED SENSOR)
  1. Turn the power switch off.

  1. Connect the Techstream to the DLC3.

  1. Turn the power switch on (READY).

  1. Select the Data List mode on the Techstream (Click here).

  1. Drive the vehicle several times and check that the speed values detected at all 4 wheels displayed on the Techstream are the same.

    DATA LIST: ABS/TRAC/VSC 
    Item
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    FR Wheel Speed
    FR wheel speed sensor reading /
    min.: 0 mph (0 km/h), max.: 202 mph (326.4 km/h)
    Actual wheel speed
    Similar speed as indicated on speedometer
    FL Wheel Speed
    FL wheel speed sensor reading /
    min.: 0 mph (0 km/h), max.: 202 mph (326.4 km/h)
    Actual wheel speed
    Similar speed as indicated on speedometer
    RR Wheel Speed
    RR wheel speed sensor reading /
    min.: 0 mph (0 km/h), max.: 202 mph (326.4 km/h)
    Actual wheel speed
    Similar speed as indicated on speedometer
    RL Wheel Speed
    RL wheel speed sensor reading /
    min.: 0 mph (0 km/h), max.: 202 mph (326.4 km/h)
    Actual wheel speed
    Similar speed as indicated on speedometer

    OK:
    The vehicle speed detected at all 4 wheels must be indicated on the Techstream.



NG
CHECK SPEED SENSOR SIGNAL CIRCUIT (BRAKE CONTROL SYSTEM) (Click here)
OK


4.RECONFIRM DTC OUTPUT
  1. Turn the power switch off.

  1. Clear the DTC (Click here).

  1. Turn the power switch on (READY).

  1. Drive the vehicle at the speed of 32 km/h (20 mph) or more for at least 60 seconds.

  1. Check if the same DTC is recorded

    Result:

    Result
    Proceed to
    DTC (C1348) is output
    A
    DTC (C1348) is not output
    B



B
END
A

REPLACE SKID CONTROL ECU ASSEMBLY (Click here)