Home › BRAKE › BRAKE CONTROL › ELECTRONICALLY CONTROLLED BRAKE SYSTEM

DTC    C0210/33    Rear Speed Sensor RH Circuit

DTC    C0215/34    Rear Speed Sensor LH Circuit

DTC    C1273/73    Low Output Signal of Rear Speed Sensor RH (Test Mode DTC)

DTC    C1274/74    Low Output Signal of Rear Speed Sensor LH (Test Mode DTC)

for Preparation Click here


DESCRIPTION

The speed sensor detects wheel speed and sends the appropriate signals to the skid control ECU. These signals are used for ABS control.
Speed sensor rotors have 48 serrations. The hall IC type speed sensor use the frequency of output pulses to detect the vehicle speed. Because the sensor outputs digital pulses, it can detect vehicle speeds even when the vehicle is nearly stationary.
DTCs C1273/73 and C1274/74 can be deleted when the speed sensor sends a wheel speed signal or when Test Mode ends. DTCs C1273/73 and C1274/74 are output only in Test Mode.

C172023E02


DTC Code
INF Code
DTC Detection Condition
Trouble Area
C0210/33
277
At a vehicle speed of 10 km/h (6 mph) or more, an open or short signal occurs in the speed sensor circuit.
  1. Rear speed sensor RH
  2. Speed sensor circuit
  3. Sensor installation
  4. Speed sensor rotor
  5. Skid control ECU
↑
278
More than one speed sensor circuit signal is abnormal.
↑
↑
279
Speed sensor circuit signal is open for 0.5 seconds or more.
↑
↑
280
A momentary interruption of the sensor signal from the speed sensor occurs 255 times or more.
↑
↑
281
Frequency of 2.7 kHz or higher is input.
  1. Rear speed sensor RH
  2. Speed sensor circuit
  3. Speed sensor rotor
  4. Skid control ECU
↑
282
Speed sensor rotational direction signal changes 7 times with the power switch on (IG) while driving at 10 km/h (6 mph) or more.
  1. Rear speed sensor RH
  2. Speed sensor circuit
  3. Sensor installation
  4. Speed sensor rotor
  5. Skid control ECU
↑
283
Speed sensor rotational direction signal is not the same as that of the other sensors for 1 second while driving at 30 km/h (18 mph) or more.
↑
↑
284
A speed sensor rotational direction signal is not detected normally and the rotational direction signals from the other speed sensors are not the same for 1 second while driving at 30 km/h (18 mph) or more.
↑
↑
285
3 of the speed sensors detect normal reverse signals, and the other speed sensor signal malfunctions 75 times with the power switch on (IG) while reversing at 3 km/h (1.8 mph).
↑
↑
286
At a vehicle speed of 10 km/h (6 mph) or more, the output from the vehicle speed sensor is halved for 5 seconds or more.
↑
↑
287
Reverse signal is output for 1 second or more while driving at 100 km/h (60 mph) or more.
↑
↑
288
With the voltage of IG1 terminal 9.5 V or more, the sensor power supply voltage decreases for 0.5 seconds or more.
  1. Speed sensor circuit
  2. Skid control ECU
C0215/34
290
At a vehicle speed of 10 km/h (6 mph) or more, an open or short signal occurs in the speed sensor circuit.
  1. Rear speed sensor LH
  2. Speed sensor circuit
  3. Sensor installation
  4. Speed sensor rotor
  5. Skid control ECU
↑
291
More than one speed sensor circuit signal is abnormal.
↑
↑
292
Speed sensor circuit signal is open for 0.5 seconds or more.
↑
↑
293
A momentary interruption of the sensor signal from the speed sensor occurs 255 times or more.
↑
↑
294
Frequency of 2.7 kHz or higher is input.
  1. Rear speed sensor LH
  2. Speed sensor circuit
  3. Speed sensor rotor
  4. Skid control ECU
↑
295
Speed sensor rotational direction signal changes 7 times with the power switch on (IG) while driving at 10 km/h (6 mph) or more.
  1. Rear speed sensor LH
  2. Speed sensor circuit
  3. Sensor installation
  4. Speed sensor rotor
  5. Skid control ECU
↑
296
Speed sensor rotational direction signal is not the same as that of the other sensors for 1 second while driving at 30 km/h (18 mph) or more.
↑
↑
297
A speed sensor rotational direction signal is not detected normally and the rotational direction signals from the other speed sensors are not the same for 1 second while driving at 30 km/h (18 mph) or more.
↑
↑
298
3 of the speed sensors detect normal reverse signals, and the other speed sensor signal malfunctions 75 times with the power switch on (IG) while reversing at 3 km/h (1.8 mph).
↑
↑
299
At a vehicle speed of 10 km/h (6 mph) or more, the output from the vehicle speed sensor is halved for 5 seconds or more.
↑
↑
300
Reverse signal is output for 1 second or more while driving at 100 km/h (60 mph) or more.
↑
↑
301
With the voltage of IG1 terminal 9.5 V or more, the sensor power supply voltage decreases for 0.5 seconds or more.
  1. Speed sensor circuit
  2. Skid control ECU
C1273/73
C1274/74
-
Detected only during Test Mode.
  1. Rear speed sensor RH/LH
  2. Sensor installation
  3. Speed sensor rotor

HINT:
  1. DTCs C0210/33 and C1273/73 are for the rear speed sensor RH.
  2. DTCs C0215/34 and C1274/74 are for the rear speed sensor LH.
  3. The brake warning light / red (malfunction) comes on when speed sensor malfunctions are detected in two or more wheels.


WIRING DIAGRAM


C173793E02


INSPECTION PROCEDURE

NOTICE:
When replacing the skid control ECU, perform initialization and calibration of the linear solenoid valve (Click here).

1.CHECK HARNESS AND CONNECTOR (MOMENTARY INTERRUPTION)
  1. Using the Techstream, check for any momentary interruptions in the wire harness and connector corresponding to a DTC (Click here).

    ABS / VSC / TRAC: 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    RR Speed Open
    RR speed sensor open detection / ERROR or NORMAL
    ERROR: Momentary interruption
    NORMAL: Normal
    -
    RL Speed Open
    RL speed sensor open detection / ERROR or NORMAL
    ERROR: Momentary interruption
    NORMAL: Normal
    -

    Result:

    Result
    Proceed to
    There are momentary interruptions
    A
    There are no momentary interruptions
    B
    There is a constant open circuit
    C

    HINT:
    Perform the above inspection before removing the sensor and connector.



B
Go to step 4

C
Go to step 7
A


2.REPAIR OR REPLACE HARNESS OR CONNECTOR (SKID CONTROL ECU - REAR SPEED SENSOR)
  1. Turn the power switch off.

  1. Repair or replace the harness or connector.

  1. Check for any momentary interruption between the skid control ECU and rear speed sensor (Click here).

  1. Check that there are no momentary interruptions.


NEXT


3.RECONFIRM DTC
  1. Turn the power switch off.

  1. Clear the DTCs (Click here).

  1. Turn the power switch on (READY).

  1. Drive the vehicle at a speed of 32 km/h (20 mph) or more for at least 60 seconds.

  1. Check if the same DTC is recorded (Click here).

    Result:

    Result
    Proceed to
    DTCs (C0210/33 and/or C0215/34) are output
    A
    DTCs (C0210/33 and C0215/34) are not output
    B

    HINT:
    If troubleshooting has been carried out according to the Problem Symptoms Table, refer back to the table and proceed to the next step (Click here).



B
END
A


4.READ VALUE USING TECHSTREAM (REAR SPEED SENSOR)
  1. Turn the power switch off.

  1. Connect the Techstream to the DLC3.

  1. Turn the power switch on (READY).

  1. Select the Data List mode on the Techstream (Click here).

    ABS / VSC / TRAC: 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    RR Wheel Speed
    RR wheel speed sensor reading / min.: 0 km/h (0 mph), max.: 326.4 km/h (202 mph)
    Actual wheel speed
    Similar speed as indicated on speedometer
    RL Wheel Speed
    RL wheel speed sensor reading / min.: 0 km/h (0 mph), max.: 326.4 km/h (202 mph)
    Actual wheel speed
    Similar speed as indicated on speedometer

  1. Check that there is no difference between the speed value output from the speed sensor displayed on the Techstream and the speed value displayed on the speedometer when driving the vehicle.

    HINT:
    Factors that affect the indicated vehicle speed include tire size, tire inflation, and tire wear. The speed indicated on the speedometer has an allowable margin of error. This can be tested using a speedometer tester (calibrated chassis dynamometer). For details about testing and the margin of error, see the reference chart (Click here).

    OK:
    The speed value output from the speed sensor displayed on the Techstream is the same as the actual vehicle speed measured using a speedometer tester (calibrated chassis dynamometer).



NG
Go to step 7
OK


5.PERFORM TEST MODE (SIGNAL CHECK)
  1. Turn the power switch off.

  1. Perform the sensor check in the Test Mode procedure (Click here).

    OK:
    All Test Mode DTCs are erased.



NG
Go to step 7
OK


6.RECONFIRM DTC
  1. Turn the power switch off.

  1. Clear the DTCs (Click here).

  1. Turn the power switch on (READY).

  1. Drive the vehicle at a speed of 32 km/h (20 mph) or more for at least 60 seconds.

  1. Check if the same DTC is recorded (Click here).

    Result:

    Result
    Proceed to
    DTCs (C0210/33 and C0215/34) are not output
    A
    DTCs (C0210/33 and/or C0215/34) are output
    B

    HINT:
    If troubleshooting has been carried out according to the Problem Symptoms Table, refer back to the table and proceed to the next step (Click here).



B
Go to step 11
A

CHECK FOR INTERMITTENT PROBLEMS (SYMPTOM SIMULATION) (Click here)  

7.CHECK REAR SPEED SENSOR INSTALLATION


    C144929E13
  1. Turn the power switch off.

  1. Check the speed sensor installation.

    OK:
    There is no clearance between the sensor and the rear axle carrier.
    The installation bolt is tightened properly.
    Torque:
    8.0 N*m (82 kgf*cm, 71 in.*lbf)



NG
INSTALL REAR SPEED SENSOR CORRECTLY (Click here)
OK


8.CHECK REAR SPEED SENSOR TIP
  1. Remove the rear speed sensor (Click here).

  1. Check the speed sensor tip.

    OK:
    The sensor tip is free of scratches, oil, and foreign matter.

    NOTICE:
    Check the speed sensor signal after cleaning or replacement (Click here).



NG
CLEAN OR REPLACE REAR SPEED SENSOR
OK


9.INSPECT REAR SPEED SENSOR
C180256E02
  1. Install the rear speed sensor.

  1. Make sure that there is no looseness at the locking part and the connecting part of the connectors.

  1. Disconnect the rear speed sensor connectors.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    for RH:
    Tester Connection
    Condition
    Specified Condition
    1 (RR+) - Body ground
    Always
    10 kΩ or higher
    2 (RR-) - Body ground
    Always
    10 kΩ or higher
    for LH:
    Tester Connection
    Condition
    Specified Condition
    1 (RL+) - Body ground
    Always
    10 kΩ or higher
    2 (RL-) - Body ground
    Always
    10 kΩ or higher

    NOTICE:
    Check the speed sensor signal after replacement (Click here).



NG
REPLACE REAR SPEED SENSOR (Click here)
OK


10.CHECK HARNESS AND CONNECTOR (SKID CONTROL ECU - REAR SPEED SENSOR)
C173830E01
  1. Make sure that there is no looseness at the locking part and the connecting part of the connectors.

  1. Disconnect the skid control ECU connectors.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    for RH:
    Tester Connection
    Condition
    Specified Condition
    A47-31 (RR+) - N20-1 (RR+)
    Always
    Below 1 Ω
    A47-31 (RR+) - Body ground
    Always
    10 kΩ or higher
    A47-23 (RR-) - N20-2 (RR-)
    Always
    Below 1 Ω
    A47-23 (RR-) - Body ground
    Always
    10 kΩ or higher
    for LH:
    Tester Connection
    Condition
    Specified Condition
    A44-27 (RL+) - O39-1 (RL+)
    Always
    Below 1 Ω
    A44-27 (RL+) - Body ground
    Always
    10 kΩ or higher
    A44-35 (RL-) - O39-2 (RL-)
    Always
    Below 1 Ω
    A44-35 (RL-) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


11.CHECK REAR SPEED SENSOR AND REAR SPEED SENSOR ROTOR SERRATIONS
C175126E02
  1. Turn the power switch off.

  1. Reconnect the skid control ECU connectors and the rear speed sensor connectors.

  1. Connect the oscilloscope to the rear speed sensor terminal of the skid control ECU.

  1. Check the waveform output when the wheels are rotated.

    OK:
    The same waveform is output from all the sensors and there is no noise or interference in the waveform.

    HINT:
    1. As the vehicle speed (wheel revolution speed) increases, a cycle of the waveform narrows and the output voltage becomes greater.
    2. When noise is identified in the waveform on the oscilloscope, the erratic signals are generated due to speed sensor rotor scratches, looseness or foreign matter attached to it.

    NOTICE:
    Check the speed sensor signal after cleaning or replacement (Click here).

    HINT:
    If the rear speed sensor rotor needs to be replaced, replace it together with the outboard joint shaft assembly.



NG
CLEAN OR REPLACE REAR SPEED SENSOR OR REAR SPEED SENSOR ROTOR
OK


12.RECONFIRM DTC
  1. Turn the power switch off.

  1. Clear the DTCs (Click here).

  1. Turn the power switch on (READY).

  1. Drive the vehicle at a speed of 32 km/h (20 mph) or more for at least 60 seconds.

  1. Check if the same DTC is recorded (Click here).

    Result:

    Result
    Proceed to
    DTCs (C0210/33 and C0215/34) are not output
    A
    DTCs (C0210/33 and/or C0215/34) are output
    B

    HINT:
    If troubleshooting has been carried out according to the Problem Symptoms Table, refer back to the table and proceed to the next step (Click here).



B
REPLACE SKID CONTROL ECU (Click here)
A

CHECK FOR INTERMITTENT PROBLEMS (SYMPTOM SIMULATION) (Click here)