Home › BRAKE › BRAKE CONTROL › ELECTRONICALLY CONTROLLED BRAKE SYSTEM

DTC    C0200/31    Front Speed Sensor RH Circuit

DTC    C0205/32    Front Speed Sensor LH Circuit

DTC    C1271/71    Low Output Signal of Front Speed Sensor RH (Test Mode DTC)

DTC    C1272/72    Low Output Signal of Front Speed Sensor LH (Test Mode DTC)

for Preparation Click here


DESCRIPTION

The speed sensor detects wheel speed and sends the appropriate signals to the skid control ECU. These signals are used for ABS control.
Speed sensor rotors have 48 serrations. The hall IC type speed sensor use the frequency of output pulses to detect the vehicle speed. Because the sensor outputs digital pulses, it can detect vehicle speeds even when the vehicle is nearly stationary.
DTCs C1271/71 and C1272/72 can be deleted when the speed sensor sends a wheel speed signal or when Test Mode ends. DTCs C1271/71 and C1272/72 are output only in Test Mode.

C172023E03


DTC Code
INF Code
DTC Detection Condition
Trouble Area
C0200/31
251
At a vehicle speed of 10 km/h (6 mph) or more, an open or short signal occurs in the speed sensor circuit.
  1. Front speed sensor RH
  2. Speed sensor circuit
  3. Sensor installation
  4. Speed sensor rotor
  5. Skid control ECU
↑
252
More than one speed sensor circuit signal is abnormal.
↑
↑
253
Speed sensor circuit signal is open for 0.5 seconds or more.
↑
↑
254
A momentary interruption of the sensor signal from the speed sensor occurs 255 times or more.
↑
↑
255
Frequency of 2.7 kHz or higher is input.
  1. Front speed sensor RH
  2. Speed sensor circuit
  3. Speed sensor rotor
  4. Skid control ECU
↑
256
Speed sensor rotational direction signal changes 7 times with the power switch on (IG) while driving at 10 km/h (6 mph) or more.
  1. Front speed sensor RH
  2. Speed sensor circuit
  3. Sensor installation
  4. Speed sensor rotor
  5. Skid control ECU
↑
257
Speed sensor rotational direction signal is not the same as that of the other sensors for 1 second while driving at 30 km/h (18 mph) or more.
↑
↑
258
A speed sensor rotational direction signal is not detected normally and the rotational direction signals from the other speed sensors are not the same for 1 second while driving at 30 km/h (18 mph) or more.
↑
↑
259
3 of the speed sensors detect normal reverse signals, and the other speed sensor signal malfunctions 75 times with the power switch on (IG) while reversing at 3 km/h (1.8 mph).
↑
↑
260
At a vehicle speed of 10 km/h (6 mph) or more, the output from the vehicle speed sensor is halved for 5 seconds or more.
↑
↑
261
Reverse signal is output for 1 second or more while driving at 100 km/h (60 mph) or more.
↑
↑
262
With the voltage of IG1 terminal 9.5 V or more, the sensor power supply voltage decreases for 0.5 seconds or more.
  1. Speed sensor circuit
  2. Skid control ECU
C0205/32
264
At a vehicle speed of 10 km/h (6 mph) or more, an open or short signal occurs in the speed sensor circuit.
  1. Front speed sensor LH
  2. Speed sensor circuit
  3. Sensor installation
  4. Speed sensor rotor
  5. Skid control ECU
↑
265
More than one speed sensor circuit signal is abnormal.
↑
↑
266
Speed sensor circuit signal is open for 0.5 seconds or more.
↑
↑
267
A momentary interruption of the sensor signal from the speed sensor occurs 255 times or more.
↑
↑
268
Frequency of 2.7 kHz or higher is input.
  1. Front speed sensor LH
  2. Speed sensor circuit
  3. Speed sensor rotor
  4. Skid control ECU
↑
269
Speed sensor rotational direction signal changes 7 times with the power switch on (IG) while driving at 10 km/h (6 mph) or more.
  1. Front speed sensor LH
  2. Speed sensor circuit
  3. Sensor installation
  4. Speed sensor rotor
  5. Skid control ECU
↑
270
Speed sensor rotational direction signal is not the same as that of the other sensors for 1 second while driving at 30 km/h (18 mph) or more.
↑
↑
271
A speed sensor rotational direction signal is not detected normally and the rotational direction signals from the other speed sensors are not the same for 1 second while driving at 30 km/h (18 mph) or more.
↑
↑
272
3 of the speed sensors detect normal reverse signals, and the other speed sensor signal malfunctions 75 times with the power switch on (IG) while reversing at 3 km/h (1.8 mph).
↑
↑
273
At a vehicle speed of 10 km/h (6 mph) or more, the output from the vehicle speed sensor is halved for 5 seconds or more.
↑
↑
274
Reverse signal is output for 1 second or more while driving at 100 km/h (60 mph) or more.
↑
↑
275
With the voltage of IG1 terminal 9.5 V or more, the sensor power supply voltage decreases for 0.5 seconds or more.
  1. Speed sensor circuit
  2. Skid control ECU
C1271/71
C1272/72
-
Detected only during Test Mode.
  1. Front speed sensor RH/LH
  2. Sensor installation
  3. Speed sensor rotor

HINT:
  1. DTCs C0200/31 and C1271/71 are for the front speed sensor RH.
  2. DTCs C0205/32 and C1272/72 are for the front speed sensor LH.
  3. The brake warning light / red (malfunction) comes on when speed sensor malfunctions are detected in two or more wheels.


WIRING DIAGRAM


C173793E01


INSPECTION PROCEDURE

NOTICE:
When replacing the skid control ECU, perform initialization and calibration of the linear solenoid valve (Click here).

1.CHECK HARNESS AND CONNECTOR (MOMENTARY INTERRUPTION)
  1. Using the Techstream, check for any momentary interruptions in the wire harness and connector corresponding to a DTC (Click here).

    ABS / VSC / TRAC: 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    FR Speed Open
    FR speed sensor open detection / ERROR or NORMAL
    ERROR: Momentary interruption
    NORMAL: Normal
    -
    FL Speed Open
    FL speed sensor open detection / ERROR or NORMAL
    ERROR: Momentary interruption
    NORMAL: Normal
    -

    Result:

    Result
    Proceed to
    There are momentary interruptions
    A
    There are no momentary interruptions
    B
    There is a constant open circuit
    C

    HINT:
    Perform the above inspection before removing the sensor and connector.



B
Go to step 4

C
Go to step 7
A


2.REPAIR OR REPLACE HARNESS OR CONNECTOR (SKID CONTROL ECU - FRONT SPEED SENSOR)
  1. Turn the power switch off.

  1. Repair or replace the harness or connector.

  1. Check for any momentary interruption between the skid control ECU and front speed sensor (Click here).

  1. Check that there are no momentary interruptions.


NEXT


3.RECONFIRM DTC
  1. Turn the power switch off.

  1. Clear the DTCs (Click here).

  1. Turn the power switch on (READY).

  1. Drive the vehicle at a speed of 32 km/h (20 mph) or more for at least 60 seconds.

  1. Check if the same DTC is recorded (Click here).

    Result:

    Result
    Proceed to
    DTCs (C0200/31 and/or C0205/32) are output
    A
    DTCs (C0200/31 and C0205/32) are not output
    B

    HINT:
    If troubleshooting has been carried out according to the Problem Symptoms Table, refer back to the table and proceed to the next step (Click here).



B
END
A


4.READ VALUE USING TECHSTREAM (FRONT SPEED SENSOR)
  1. Turn the power switch off.

  1. Connect the Techstream to the DLC3.

  1. Turn the power switch on (READY).

  1. Select the Data List mode on the Techstream (Click here).

    ABS / VSC / TRAC: 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    FR Wheel Speed
    FR wheel speed sensor reading / min.: 0 km/h (0 mph), max.: 326.4 km/h (202 mph)
    Actual wheel speed
    Similar speed as indicated on speedometer
    FL Wheel Speed
    FL wheel speed sensor reading / min.: 0 km/h (0 mph), max.: 326.4 km/h (202 mph)
    Actual wheel speed
    Similar speed as indicated on speedometer

  1. Check that there is no difference between the speed value output from the speed sensor displayed on the Techstream and the speed value displayed on the speedometer when driving the vehicle.

    HINT:
    Factors that affect the indicated vehicle speed include tire size, tire inflation, and tire wear. The speed indicated on the speedometer has an allowable margin of error. This can be tested using a speedometer tester (calibrated chassis dynamometer). For details about testing and the margin of error, see the reference chart (Click here).

    OK:
    The speed value output from the speed sensor displayed on the Techstream is the same as the actual vehicle speed measured using a speedometer tester (calibrated chassis dynamometer).



NG
Go to step 7
OK


5.PERFORM TEST MODE (SIGNAL CHECK)
  1. Turn the power switch off.

  1. Perform the sensor check in the Test Mode procedure (Click here).

    OK:
    All Test Mode DTCs are erased.



NG
Go to step 7
OK


6.RECONFIRM DTC
  1. Turn the power switch off.

  1. Clear the DTCs (Click here).

  1. Turn the power switch on (READY).

  1. Drive the vehicle at a speed of 32 km/h (20 mph) or more for at least 60 seconds.

  1. Check if the same DTC is recorded (Click here).

    Result:

    Result
    Proceed to
    DTCs (C0200/31 and C0205/32) are not output
    A
    DTCs (C0200/31 and/or C0205/32) are output
    B

    HINT:
    If troubleshooting has been carried out according to the Problem Symptoms Table, refer back to the table and proceed to the next step (Click here).



B
Go to step 11
A

CHECK FOR INTERMITTENT PROBLEMS (SYMPTOM SIMULATION) (Click here)  

7.CHECK FRONT SPEED SENSOR INSTALLATION


    C144929E12
  1. Turn the power switch off.

  1. Check the speed sensor installation.

    OK:
    There is no clearance between the sensor and the front steering knuckle.
    The installation bolt is tightened properly.
    Torque:
    8.0 N*m (82 kgf*cm, 71 in.*lbf)



NG
INSTALL FRONT SPEED SENSOR CORRECTLY (Click here)
OK


8.CHECK FRONT SPEED SENSOR TIP
  1. Remove the front speed sensor (Click here).

  1. Check the speed sensor tip.

    OK:
    The sensor tip is free of scratches, oil, and foreign matter.

    NOTICE:
    Check the speed sensor signal after cleaning or replacement (Click here).



NG
CLEAN OR REPLACE FRONT SPEED SENSOR
OK


9.INSPECT FRONT SPEED SENSOR
C109455E03
  1. Install the front speed sensor.

  1. Make sure that there is no looseness at the locking part and the connecting part of the connectors.

  1. Disconnect the front speed sensor connectors.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    for RH:
    Tester Connection
    Condition
    Specified Condition
    2 (FR+) - Body ground
    Always
    10 kΩ or higher
    1 (FR-) - Body ground
    Always
    10 kΩ or higher
    for LH:
    Tester Connection
    Condition
    Specified Condition
    2 (FL+) - Body ground
    Always
    10 kΩ or higher
    1 (FL-) - Body ground
    Always
    10 kΩ or higher

    NOTICE:
    Check the speed sensor signal after replacement (Click here).



NG
REPLACE FRONT SPEED SENSOR (Click here)
OK


10.CHECK HARNESS AND CONNECTOR (SKID CONTROL ECU - FRONT SPEED SENSOR)
C173794E01
  1. Make sure that there is no looseness at the locking part and the connecting part of the connectors.

  1. Disconnect the skid control ECU connectors.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    for RH:
    Tester Connection
    Condition
    Specified Condition
    A46-22 (FR+) - A29-2 (FR+)
    Always
    Below 1 Ω
    A46-22 (FR+) - Body ground
    Always
    10 kΩ or higher
    A46-32 (FR-) - A29-1 (FR-)
    Always
    Below 1 Ω
    A46-32 (FR-) - Body ground
    Always
    10 kΩ or higher
    for LH:
    Tester Connection
    Condition
    Specified Condition
    A45-22 (FL+) - A12-2 (FL+)
    Always
    Below 1 Ω
    A45-22 (FL+) - Body ground
    Always
    10 kΩ or higher
    A45-28 (FL-) - A12-1 (FL-)
    Always
    Below 1 Ω
    A45-28 (FL-) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


11.CHECK FRONT SPEED SENSOR AND FRONT SPEED SENSOR ROTOR SERRATIONS
C175126E01
  1. Turn the power switch off.

  1. Reconnect the skid control ECU connectors and the front speed sensor connectors.

  1. Connect the oscilloscope to the front speed sensor terminal of the skid control ECU.

  1. Check the waveform output when the wheels are rotated.

    OK:
    The same waveform is output from all the sensors and there is no noise or interference in the waveform.

    HINT:
    1. As the vehicle speed (wheel revolution speed) increases, a cycle of the waveform narrows and the output voltage becomes greater.
    2. When noise is identified in the waveform on the oscilloscope, the erratic signals are generated due to speed sensor rotor scratches, looseness or foreign matter attached to it.

    NOTICE:
    Check the speed sensor signal after cleaning or replacement (Click here).

    HINT:
    If the front speed sensor rotor needs to be replaced, replace it together with the front drive outboard joint shaft assembly.



NG
CLEAN OR REPLACE FRONT SPEED SENSOR OR FRONT SPEED SENSOR ROTOR
OK


12.RECONFIRM DTC
  1. Turn the power switch off.

  1. Clear the DTCs (Click here).

  1. Turn the power switch on (READY).

  1. Drive the vehicle at a speed of 32 km/h (20 mph) or more for at least 60 seconds.

  1. Check if the same DTC is recorded (Click here).

    Result:

    Result
    Proceed to
    DTCs (C0200/31 and C0205/32) are not output
    A
    DTCs (C0200/31 and/or C0205/32) are output
    B

    HINT:
    If troubleshooting has been carried out according to the Problem Symptoms Table, refer back to the table and proceed to the next step (Click here).



B
REPLACE SKID CONTROL ECU (Click here)
A

CHECK FOR INTERMITTENT PROBLEMS (SYMPTOM SIMULATION) (Click here)