Make sure to release vacuum from the brake booster assembly before removing the brake master cylinder sub-assembly from the brake booster assembly.
1. PRECAUTION
After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work.
Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION
2. RECOVER REFRIGERANT FROM REFRIGERATION SYSTEM
3.REMOVE FRONT WHEEL RH
4.REMOVE BRAKE MASTER CYLINDER SUB-ASSEMBLY WITH WAY
5.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL
When disconnecting the cable, some systems need to be initialized after the cable is reconnected.
Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION
6.DRAIN ENGINE COOLANT
11209
7.REMOVE V-BANK COVER SUB-ASSEMBLY
17705
8.REMOVE AIR CLEANER CAP WITH AIR CLEANER HOSE
17801
9.REMOVE AIR CLEANER FILTER ELEMENT SUB-ASSEMBLY
82111
10.SEPARATE ENGINE ROOM MAIN WIRE
| *a | Wire Harness Protector |
Remove the bolt and disengage the clamp to separate the wire harness protector.
Disengage the 5 clamps to separate the engine room main wire.
47220D
11.REMOVE BRAKE MASTER CYLINDER RESERVOIR ASSEMBLY
| *1 | Brake Master Cylinder Reservoir Assembly |
| *2 | Reservoir Bracket |
Disconnect the reservoir level switch connector and remove the bolt from the brake master cylinder reservoir assembly.
Move the brake master cylinder reservoir assembly as shown in the illustration to disengage the 2 claws, and remove it.
47233
12.REMOVE RESERVOIR BRACKET
Disengage the clamp to separate the engine room main wire.
Remove the 2 nuts and reservoir bracket.
44773F
13.DISCONNECT UNION TO CHECK VALVE HOSE
Slide the clip and disconnect the union to check valve hose from the brake booster assembly.
12327A
14.REMOVE NO. 2 ENGINE MOUNTING STAY RH
12313
15.REMOVE ENGINE MOVING CONTROL ROD BRACKET
88704
16.SEPARATE SUCTION HOSE SUB-ASSEMBLY
Disengage the clamp to separate the suction hose sub-assembly.
Do not deform the refrigerant lines.
Do not damage the clamp.
Disengage the clamp to separate the suction hose sub-assembly from the brake actuator assembly.
Do not deform the refrigerant lines.
Do not damage the clamp.
Disengage the claw to separate the suction hose sub-assembly.
Do not deform the refrigerant lines.
Do not damage the clamp.
Disengage the claw to release the piping clamp.
Do not damage the clamp.
Remove the bolt and rotate the hook connector.
Disconnect the suction hose sub-assembly from the air conditioning unit assembly.
Remove the O-ring from the suction hose sub-assembly.
Seal the openings of the disconnected parts using vinyl tape to prevent entry of moisture and foreign matter.
Separate the suction hose sub-assembly from the vehicle body.
Do not deform the refrigerant lines.
Do not damage the clamp.
17.SEPARATE AIR CONDITIONER TUBE AND ACCESSORY ASSEMBLY
Disengage the clamp to separate the air conditioner tube and accessory assembly from the piping clamp.
Do not deform the refrigerant lines.
Do not damage the clamp.
Disengage the clamp to separate the air conditioner tube and accessory assembly from the brake actuator assembly.
Do not deform the refrigerant lines.
Do not damage the clamp.
Remove the bolt and separate the air conditioner tube and accessory assembly.
Do not deform the refrigerant lines.
Disconnect the air conditioner tube and accessory assembly from the air conditioning unit assembly.
Remove the O-ring from the air conditioner tube and accessory assembly.
Seal the openings of the disconnected parts using vinyl tape to prevent entry of moisture and foreign matter.
Remove the nut and separate the air conditioner tube and accessory assembly from the vehicle body.
Do not deform the refrigerant lines.
88704
18.DISCONNECT SUCTION HOSE SUB-ASSEMBLY
Remove the piping clamp.
Click hereVehicle Interior>HEATING / AIR CONDITIONING>REFRIGERANT LINE>REMOVAL
Disconnect the suction hose sub-assembly from the No. 1 air conditioning accessory assembly.
Do not deform the refrigerant lines.
Remove the 2 O-rings from the suction hose sub-assembly.
Seal the openings of the disconnected parts using vinyl tape to prevent entry of moisture and foreign matter.
19.SEPARATE BRAKE LINE
Using a union nut wrench, disconnect the 3 brake lines from the brake actuator assembly.
Do not kink or damage the brake lines.
Do not allow any foreign matter such as dirt or dust to enter the brake line from the connecting parts.
Disengage the clamp to separate the 3 brake lines.
Do not damage the clamp.
Do not kink or damage the brake lines.
| *1 | Front No. 6 Brake Tube |
| *2 | Front No. 7 Brake Tube |
| *3 | Front No. 8 Brake Tube |
Disengage the 3 clamps and remove the front No. 6 brake tube and front No. 7 brake tube.
Do not damage the 3 clamps.
Do not kink or damage the brake lines.
Remove the front No. 6 brake tube and front No. 7 brake tube while avoiding the front No. 8 brake tube.
22030
20.REMOVE THROTTLE BODY WITH MOTOR ASSEMBLY
22271
21.REMOVE THROTTLE BODY GASKET
17190
22.REMOVE INTAKE AIR SURGE TANK ASSEMBLY
22267A
23.REMOVE THROTTLE BODY BRACKET
17125
24.REMOVE NO. 1 SURGE TANK STAY
12262
25.REMOVE NO. 2 VENTILATION HOSE
Slide the clip and disconnect the No. 2 ventilation hose to remove it from the cylinder head cover sub-assembly.
44781
26.REMOVE HOSE BRACKET
Disengage the clamp to separate the engine wire.
Remove the bolt and hose bracket.
82121
27.SEPARATE ENGINE WIRE
|
Bolt |
|
Connector |
Remove the bolt, disengage the 4 clamps and disconnect the 10 connectors.
Remove the bolt and separate the engine wire from the cylinder head cover sub-assembly.
19500
28.REMOVE IGNITION COIL ASSEMBLY
Remove the 3 bolts and 3 ignition coil assemblies.
23292D
29.REMOVE FUEL HOSE PROTECTOR
11322F
30.REMOVE NO. 2 TIMING GEAR COVER
15771M
31.REMOVE OIL PIPE
11201
32.REMOVE CYLINDER HEAD COVER SUB-ASSEMBLY
47101A
33.REMOVE BRAKE PEDAL RETURN SPRING
34.LOOSEN LOCK NUT
| *1 | Lock Nut |
| *2 | Brake Master Cylinder Push Rod Clevis |
Loosen the lock nut of the brake master cylinder push rod clevis.
47264A
35.REMOVE PUSH ROD PIN
44610
36.REMOVE BRAKE BOOSTER ASSEMBLY
Remove the 4 nuts and push the brake booster assembly toward the engine compartment.
Remove the brake master cylinder push rod clevis and lock nut from the brake booster assembly.
Remove the brake booster assembly from the vehicle body.
44785
37.REMOVE BRAKE BOOSTER GASKET