Home › Drivetrain › UA80F (AUTOMATIC TRANSMISSION / TRANSAXLE) › TRANSMISSION WIRE(When Using the Engine Support Bridge) › from 2018.09
RM3160E _52 Drivetrain _060165 UA80F AUTOMATIC TRANSMISSION / TRANSAXLE _0304092 TRANSMISSION WIRE(When Using the Engine Support Bridge) A

UA80F AUTOMATIC TRANSMISSION / TRANSAXLE  TRANSMISSION WIRE(When Using the Engine Support Bridge)  REMOVAL  


PROCEDURE

Hide 1. PRECAUTION

NOTICE:

After turning the engine switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION


Hide 2.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION


Hide 3.REMOVE FRONT WHEELS

Hide 4.REMOVE WINDSHIELD WIPER MOTOR AND LINK ASSEMBLY

Hide 55701J 5.REMOVE OUTER COWL TOP PANEL SUB-ASSEMBLY (for LHD)

Hide 55701J 6.REMOVE OUTER COWL TOP PANEL SUB-ASSEMBLY (for RHD)

Hide 51441 7.REMOVE NO. 1 ENGINE UNDER COVER

Hide 53876A 8.SEPARATE FRONT FENDER LINER LH

Hide 53875A 9.SEPARATE FRONT FENDER LINER RH

Hide 53737B 10.REMOVE FRONT FENDER APRON SEAL LH

Hide 53736 11.REMOVE FRONT FENDER APRON SEAL RH

Hide 53299D 12.REMOVE RADIATOR SIDE DEFLECTOR SEAL LH

Hide 53298E 13.REMOVE RADIATOR SIDE SEAL RH

Hide 53295E 14.REMOVE COOL AIR INTAKE DUCT SEAL

Hide 11209 15.REMOVE V-BANK COVER SUB-ASSEMBLY

Hide 17750A 16.REMOVE INLET AIR CLEANER ASSEMBLY

Hide 17700 17.REMOVE AIR CLEANER ASSEMBLY WITH AIR CLEANER HOSE

Hide 47220D 20.SEPARATE BRAKE MASTER CYLINDER RESERVOIR ASSEMBLY (for LHD)

Hide 22030 21.REMOVE THROTTLE BODY WITH MOTOR ASSEMBLY

Hide 12261 22.DISCONNECT VENTILATION HOSE

Hide 25860 23.DISCONNECT PURGE VALVE (PURGE VSV)

Hide 17126 24.REMOVE NO. 2 SURGE TANK STAY

Hide 17190 25.REMOVE INTAKE AIR SURGE TANK ASSEMBLY

Hide 17176 26.REMOVE AIR SURGE TANK TO INTAKE MANIFOLD GASKET

Hide 32971 30.DISCONNECT TRANSMISSION OIL THERMOSTAT

a.
C365871

Remove the 2 bolts to disconnect the transmission oil thermostat from the front frame assembly.


Hide 32942 31.DISCONNECT OUTLET NO. 1 OIL COOLER HOSE

Hide 32901C 32.DISCONNECT OIL COOLER UNION SUB-ASSEMBLY

a.
C365909C01
2.563,1.417 2.802,1.615 0.24,0.198 10 true *1
*1 Oil Cooler Union Bolt


Remove the bolt to separate the oil cooler union sub-assembly bracket portion from the automatic transaxle case sub-assembly.


b.

Remove the oil cooler union bolt, 2 gaskets and disconnect the oil cooler union sub-assembly from the automatic transaxle case sub-assembly.


Hide 35151F 33.REMOVE TRANSMISSION CASE SIDE COVER

a.
C363253

Disconnect the transmission wire connector.

HINT:

Disengage the claw, pull down the lever, and then disconnect the transmission wire connector.



b.
C365872

Loosen the bolt from the front engine mounting insulator.

NOTICE:

Do not fully remove the bolt.



c.
C365873

Loosen the nut from the engine mounting insulator LH.

NOTICE:

Do not fully remove the nut.



d.
C363229C01
1.615,0.698 2.094,0.427 true 2.135,0.354 2.385,0.521 0.25,0.167 10 true *a
*a Wooden Block


Support the automatic transaxle assembly with a jack. Insert a wooden block between the jack and the automatic transaxle assembly to prevent damage.


e.
C365874C01
2.365,1.198 2.583,1.417 0.219,0.219 10 true *a
*a 25 to 30 mm


Operate the engine support bridge and the jack to raise up the engine and automatic transaxle assembly from 25 to 30 mm (0.984 to 1.181 in.).

NOTICE:
·

Do not raise the engine and automatic transaxle more than 30 mm (1.181 in.).

·

When raising the jack, be careful to prevent contact between the transmission wire and the vehicle body.

·

Do not allow the engine assembly and automatic transaxle assembly to interfere with the body.

·

Make sure that the wire harness and hoses are not being pulled.




f.
C396661C02
0.063,0.052 0.375,0.406 0.313,0.354 12 false *A 0.063,2.271 0.375,2.625 0.313,0.354 12 false *B
*A for TMC, AW Made
*B for TMMWV Made


Remove the 10 bolts and transmission case side cover from the automatic transaxle case sub-assembly.


Hide 82125J 34.REMOVE TRANSMISSION WIRE

a.
C361008C01
0.135,0.208 0.448,0.365 0.313,0.156 10 false *a 0.615,3.229 0.927,3.385 0.313,0.156 10 false *b
*a Connector A
*b Connector B


Disengage the clamp to disconnect the transmission wire from the solenoid lock plate.


b.

Disconnect the 9 solenoid valve connectors.

HINT:
·

Using a screwdriver, disconnect the solenoid valve connector A using the procedure shown in the illustration.

·

Using a screwdriver, disconnect the solenoid valve connector B using the procedure shown in the illustration.




c.
C361010

Remove the bolt and temperature sensor clamp and disconnect the temperature sensor from the transmission valve body assembly.


d.
C365878

Disconnect the transmission revolution sensor (NT) connector and transmission revolution sensor (NC) connector.


e.
C361015

Remove the bolt and transmission wire from the automatic transmission case sub-assembly.