Home › Drivetrain › AXLE AND DIFFERENTIAL › REAR AXLE CARRIER (for 2WD) › 2020.02–2020.11
RM37A0E _52 Drivetrain _086863 AXLE AND DIFFERENTIAL _0417449 REAR AXLE CARRIER(for 2WD) A

AXLE AND DIFFERENTIAL  REAR AXLE CARRIER(for 2WD)  INSTALLATION  


CAUTION / NOTICE / HINT

NOTICE:
·

When removing or installing the rear disc brake cylinder assembly, pushing back the disc brake piston may cause a large clearance between the brake pads and brake disc. When the brake pedal is depressed with a large clearance between the brake pads and the brake disc, DTC C13DB00, C13DC00, C13DD00, C13DE00, C140000 and/or C140A00 related to abnormal brake fluid pressure may be stored. Make sure to clear any DTCs after performing this procedure.

·

While the auxiliary battery is connected, even if the ignition switch is off, the brake control system activates when the brake pedal is depressed or any door courtesy switch turns on. Therefore, when servicing the brake system components, do not operate the brake pedal or open/close the doors while the auxiliary battery is connected.



HINT:
·

Use the same procedure for the RH side and LH side.

·

The following procedure is for the LH side.



PROCEDURE

Hide 48759 1.INSTALL LOWER CONTROL ARM PIN

a.
C428096N01
1.521,1.281 2.281,1.281 false 2.354,1.208 2.813,1.406 0.458,0.198 10 false SST

Secure the rear axle carrier sub-assembly in a vise using aluminum plates.

NOTICE:

Do not overtighten the vise.



b.

Using SST, install a new lower control arm pin to the rear axle carrier sub-assembly as shown in the illustration.

SST
09650-17011  


Hide 42305 2.TEMPORARILY INSTALL REAR AXLE CARRIER SUB-ASSEMBLY

a.
C424690

Secure the rear axle carrier sub-assembly in a vise using aluminum plates.

NOTICE:

Do not overtighten the vise.



b.

Using a brass bar and a hammer, push out the bushing until it is positioned as shown in the illustration.

HINT:

Pushing out the bushing makes it easier to install the rear axle carrier sub-assembly.



c.
C424687N02
0.563,2.74 0.771,2.938 0.208,0.198 10 true A 2.865,3.094 3.031,3.26 0.167,0.167 10 true D 0.729,0.594 0.885,0.74 0.156,0.146 10 true C 2.802,0.177 2.969,0.344 0.167,0.167 10 true B 2.573,3.094 2.74,3.26 0.167,0.167 10 true D

Temporarily install the rear axle carrier sub-assembly to the rear No. 1 suspension arm assembly with the spacer and nut (A).

NOTICE:

Fully tighten the nut (A) after stabilizing the suspension.



d.

Temporarily install the rear axle carrier sub-assembly to the rear No. 2 suspension arm assembly with the bolt (B) and nut.

NOTICE:
·

Insert the bolt with the threaded end facing the front of the vehicle.

·

Because the nut has its own stopper, do not turn the nut. Tighten the bolt with the nut secured.

·

Fully tighten the bolt (B) after stabilizing the suspension.




e.

Temporarily install the rear axle carrier sub-assembly to the rear upper control arm assembly with the bolt (C) and nut.

NOTICE:
·

Insert the bolt with the threaded end facing the rear of the vehicle.

·

Because the nut has its own stopper, do not turn the nut. Tighten the bolt with the nut secured.

·

Fully tighten the bolt (C) after stabilizing the suspension.




f.

Install the rear axle carrier sub-assembly to the rear lower shock absorber bracket sub-assembly with the 2 bolts (D).

Torque:
147 N*m (1499 kgf*cm, 108 ft.*lbf)


g.

Slowly lower the rear No. 2 suspension arm assembly.


Hide 48780E 3.INSTALL REAR TRAILING ARM ASSEMBLY

Hide 42450B 4.INSTALL REAR AXLE HUB AND BEARING ASSEMBLY

Hide 42431 5.INSTALL REAR DISC

Hide 6.INSTALL REAR DISC BRAKE CYLINDER MOUNTING WITH BRAKE PAD

Hide 47850 7.INSTALL REAR DISC BRAKE CYLINDER ASSEMBLY

Hide 890C0A 8.INSTALL NO. 2 PARKING BRAKE WIRE ASSEMBLY

a.
C424685N01
1.521,3.75 1.677,3.948 0.156,0.198 10 true A 2.115,3.885 2.271,4.083 0.156,0.198 10 true A 1.448,0.479 1.604,0.677 0.156,0.198 10 true B

Install the No. 2 parking brake wire assembly to the rear trailing arm assembly with the 3 bolts.

Torque:
Bolt (A) : 15 N*m (153 kgf*cm, 11 ft.*lbf)
Bolt (B) : 8.5 N*m (87 kgf*cm, 75 in.*lbf)


b.

Install the No. 2 parking brake wire assembly to the rear axle carrier sub-assembly with the bolt.

Torque:
15 N*m (153 kgf*cm, 11 ft.*lbf)


c.

Connect the No. 2 parking brake wire assembly connector to the rear axle hub and bearing assembly.


d.

Connect the No. 2 parking brake wire assembly connector to the parking brake actuator assembly.


Hide 47319F 9.INSTALL REAR FLEXIBLE HOSE

a.

Install the rear flexible hose to the rear upper control arm assembly with the bolt.

Torque:
18.8 N*m (192 kgf*cm, 14 ft.*lbf)


Hide 48790 11.INSTALL REAR UPPER CONTROL ARM ASSEMBLY

a.

Install the rear upper control arm assembly to the rear axle carrier sub-assembly with the bolt.

Torque:
110 N*m (1122 kgf*cm, 81 ft.*lbf)

NOTICE:

Because the nut has its own stopper, do not turn the nut. Tighten the bolt with the nut secured.



Hide 48720A 12.INSTALL REAR NO. 1 SUSPENSION ARM ASSEMBLY

a.
C336798

Install the rear No. 1 suspension arm assembly with the nut.

Torque:
135 N*m (1377 kgf*cm, 100 ft.*lbf)


Hide 48740F 13.INSTALL REAR NO. 2 SUSPENSION ARM ASSEMBLY

a.

Install the rear No. 2 suspension arm assembly (rear axle carrier sub-assembly side) with the bolt.

Click hereSuspension>REAR SUSPENSION>REAR LOWER ARM>INSTALLATION


Hide 48738 14.INSTALL REAR SUSPENSION ARM COVER

Hide 15.INSTALL REAR WHEEL

Hide 16.CONNECT CABLE TO NEGATIVE AUXILIARY BATTERY TERMINAL

a.

Connect the reservoir level switch connector.


b.

Install the brake master cylinder reservoir assembly to the reservoir bracket with the bolt and nut.

Torque:
9.0 N*m (92 kgf*cm, 80 in.*lbf)


c.

Engage the clamp to install the wire harness to the brake master cylinder reservoir assembly.


d.

Connect the cable to the negative (-) auxiliary battery terminal.

Click hereGeneral>MAINTENANCE>A25A-FXS, A25B-FXS AUXILIARY BATTERY>INSTALLATION


e.

Turn the ignition switch to ON (READY).


f.

Depress the brake pedal and release it.



Hide 17.INSPECT AND ADJUST REAR WHEEL ALIGNMENT

Hide 19.PERFORM INITIALIZATION

Parking Support Brake System (Click here)
Parking Assist Monitor System (Click here)
Panoramic View Monitor System (Click here)