Home › Engine / Hybrid System › A25A-FXS, A25B-FXS (FUEL) › FUEL PUMP
RM37A0E _51 Engine / Hybrid System _086907 A25A-FXS, A25B-FXS FUEL _0417787 FUEL PUMP A

A25A-FXS, A25B-FXS FUEL  FUEL PUMP  INSTALLATION  


PROCEDURE

Hide 77020A 1.INSTALL FUEL SUCTION TUBE WITH PUMP AND GAUGE ASSEMBLY

a.

Install a new fuel suction tube set gasket to the fuel tank sub-assembly.


b.
A458410C01
1.01,2.917 1.833,2.917 true 0.406,0.885 0.563,0.885 0.563,0.885 0.667,0.698 false 0.208,0.802 0.542,1.135 0.333,0.333 10 false *a 0.76,2.833 0.969,3.021 0.208,0.188 10 true *b
*a Protrusion
*b Notch


Set the fuel suction tube with pump and gauge assembly to the fuel tank sub-assembly.

NOTICE:
·

Be careful not to bend the arm of the fuel sender gauge assembly.

·

Make sure the horizontal angle of the fuel suction plate sub-assembly is less than 90°.

·

To avoid applying excessive force to the tip of the fuel sender gauge assembly, tilt the fuel sub-tank sub-assembly diagonally and insert it into the fuel tank sub-assembly as shown in the illustration.


A458411C01
1.885,2.219 1.729,2.219 1.729,2.219 1.656,1.854 true 5.542,2.25 5.708,2.667 5.708,2.667 5.865,2.667 false 5.74,1.583 6,1.448 6,1.448 6.146,1.448 false 1.875,1.958 2.24,1.958 true 1.865,1.094 2.229,1.094 true 5.927,2.313 6.292,2.313 true 2.313,1.865 2.708,2.125 0.396,0.26 10 false *1 1.969,2.146 2.229,2.344 0.26,0.198 10 false *2 6.208,1.365 6.563,1.646 0.354,0.281 10 false *3 0.615,0.594 0.833,0.823 0.219,0.229 10 false *a 2.281,1.01 2.563,1.219 0.281,0.208 10 false *3 5.948,2.583 6.219,2.771 0.271,0.188 10 false *2 6.385,2.24 6.76,2.552 0.375,0.313 10 false *1
*1 Fuel Sender Gauge Assembly *2 Fuel Sub-tank Sub-assembly
*3 Fuel Suction Plate Sub-assembly - -
*a 90° - -




c.
A458412C01
1.833,3 0.688,2.323 0.688,2.323 1.594,1.635 true 2.771,0.708 2.917,0.708 true 0.448,2.24 0.635,2.438 0.188,0.198 10 true *a 2.969,0.625 3.156,0.823 0.188,0.198 10 true *a
*a Protrusion
V100135

Notch


Align the protrusions of the fuel suction tube with pump and gauge assembly with the notches in the fuel tank sub-assembly.


Hide 77144 2.INSTALL FUEL PUMP GAUGE RETAINER

a.

Install the fuel pump gauge retainer.

i.

While pressing down on the fuel suction tube with pump and gauge assembly, temporarily install the fuel pump gauge retainer.


ii.
A455320C01
0.792,0.708 0.969,0.708 0.969,0.708 1.354,0.927 true 2.385,0.5 2.594,0.25 2.594,0.25 2.781,0.25 true 2.26,1.438 2.469,1.792 2.469,1.792 2.656,1.792 true 0.792,1.344 1.313,1.344 true 0.885,3.01 1.958,3.01 true 2.458,0.833 2.979,0.833 true 2.031,2.927 2.25,3.146 0.219,0.219 10 true *a 2.708,1.698 2.906,1.896 0.198,0.198 10 true *b 0.573,1.25 0.76,1.448 0.188,0.198 10 true *c 0.563,0.615 0.74,0.802 0.177,0.188 10 true *d 2.844,0.156 3.042,0.333 0.198,0.177 10 true *d 3.031,0.74 3.219,0.938 0.188,0.198 10 true *c
*a Insertion Point
*b SST (Plate)
*c SST (Claw)
*d SST (Bolt)


Temporarily install SST (plate) and SST (claw) to the fuel pump gauge retainer.

SST
09808-01071  
09808-14031  (09808-01030, 09808-01090)

HINT:

Securely insert the ends of SST (claw) into the insertion points in the fuel pump gauge retainer.



iii.

While firmly pressing SST (claw) into the insertion points in the fuel pump gauge retainer, tighten SST (bolt).


iv.
A458413C01
1.042,2.219 1.156,2.219 1.156,2.219 1.354,1.958 true 1.604,3.042 1.604,3.396 true 1.604,2.708 1.875,2.708 true 1.063,0.927 0.844,0.521 0.844,0.521 0.698,0.521 true 2.115,1.354 2.438,1.479 2.438,1.479 2.615,1.479 true 2.146,1.552 2.479,1.802 2.479,1.802 2.625,1.802 true 0.74,1.896 0.854,1.896 0.854,1.896 1.146,1.771 true 1.083,1.417 1.229,1.417 1.229,1.417 1.365,1.625 true 1.75,1.125 2.177,0.948 2.177,0.948 2.344,0.948 true 1.531,3.427 1.698,3.604 0.167,0.177 10 true *a 1.938,2.625 2.115,2.813 0.177,0.188 10 true *b 0.448,0.438 0.635,0.615 0.188,0.177 10 true *c 0.5,1.802 0.698,2 0.198,0.198 10 true *d 0.792,2.135 1.01,2.313 0.219,0.177 10 true *e 2.688,1.396 2.833,1.573 0.146,0.177 10 true *f 2.667,1.708 2.885,1.885 0.219,0.177 10 true *e 0.917,1.333 1.063,1.51 0.146,0.177 10 true *f 2.375,0.854 2.542,1.063 0.167,0.208 10 true *g
*a Triangle Mark (Fuel Pump Gauge Retainer)
*b Triangle Mark (Fuel Tank Sub-assembly)
*c SST (Handle)
*d SST (Plate)
*e SST (Claw)
*f SST (Bolt)
*g Extension Bar
V100136

Front Side


Install SST (handle) and an extension bar to SST (plate).

SST
09808-14031  (09808-01010)


v.

Using SST, rotate the fuel pump gauge retainer so that the triangle mark on the fuel pump gauge retainer is aligned with the triangle mark on the fuel tank sub-assembly to install the fuel suction tube with pump and gauge assembly to the fuel tank sub-assembly.

NOTICE:
·

Do not use any tools other than specified as this may result in damage to the fuel pump gauge retainer or fuel tank sub-assembly.

·

Do not press down on SST excessively as this may make the fuel pump gauge retainer hard to rotate, and may damage components.

·

Make sure to rotate SST (handle) horizontally. If it is rotated at an angle, SST may come off.

·

Do not spin SST too fast or use an impact wrench as this may result in damage to components.

·

If SST comes off of the fuel pump gauge retainer, loosen SST (bolt) and reinstall SST.

·

Make sure that the fuel suction tube set gasket does not come off.





b.

Engage the claw to install the No. 1 fuel tube clamp.


Hide 77209F 3.CONNECT FUEL TANK MAIN TUBE SUB-ASSEMBLY

a.

Push the fuel tube joint onto the plug of the fuel suction plate sub-assembly, then install the tube joint clip.

A458414C01
5.667,1.417 6.833,2.656 1.167,1.24 4.01,1.417 5.167,2.656 1.156,1.24 2.167,0.844 2.417,0.844 true 1.854,0.938 1.542,0.563 1.542,0.563 1.375,0.563 true 5.646,0.333 5.979,0.333 false 5.833,0.646 6.167,0.646 false 4.677,1.031 4.833,1.031 4.833,1.031 4.917,0.771 false 6.24,1.927 6.354,1.594 6.354,1.594 6.51,1.594 true 4.667,1.979 4.49,2.333 4.49,2.333 4.344,2.333 true 5.656,0.865 6.208,0.865 true 5.667,0.75 6.052,0.75 6.052,0.75 6.052,0.865 true 4.458,0.969 4.771,1.135 0.313,0.167 10 false *1 6.25,0.573 6.604,0.844 0.354,0.271 10 false *2 1.125,0.49 1.333,0.667 0.208,0.177 10 true *3 6.073,0.25 6.427,0.469 0.354,0.219 10 false *a 6.313,0.792 6.698,1.115 0.385,0.323 10 false *b 4.073,1.469 4.396,1.698 0.323,0.229 10 false *c 5.771,1.49 6.104,1.698 0.333,0.208 10 false *d 4.146,2.26 4.49,2.531 0.344,0.271 10 false *e 2.458,0.771 2.656,0.969 0.198,0.198 10 true *2 6.594,1.51 6.917,1.813 0.323,0.302 10 false *e
*1 Fuel Suction Plate Sub-assembly *2 Tube Joint Clip
*3 Fuel Tank Main Tube Sub-assembly - -
*a Fuel Tube Joint *b O-ring
*c Correct *d Incorrect
*e Collar - -
V100135

Insert
V100136

Insert


NOTICE:
·

Check that there are no scratches or foreign matter around the connecting parts of the fuel tube joint and plug before performing this work.

·

Check that the fuel tube joint is securely inserted to the end.

·

Check that the tube joint clip is on the collar of the fuel tube joint.

·

After installing the tube joint clip, check that the fuel tank main tube sub-assembly is securely connected by pulling on it.




Hide 77018E 4.CONNECT FUEL TANK EVAPORATION VENT TUBE SUB-ASSEMBLY

a.

Connect the fuel tank evaporation vent tube sub-assembly to the fuel suction tube with pump and gauge assembly.

Click hereEngine / Hybrid System>A25A-FXS, A25B-FXS (FUEL)>FUEL SYSTEM>PRECAUTION


Hide 5.CONNECT FUEL TANK WIRE

a.

Engage the claw to connect the fuel tank wire.


b.

Connect the 2 fuel suction tube with pump and gauge assembly connectors.


Hide 58325E 6.INSTALL REAR FLOOR SERVICE HOLE COVER

a.

Install the rear floor service hole cover to the vehicle body with the 3 bolts.

Torque:
5.4 N*m (55 kgf*cm, 48 in.*lbf)


Hide 58510D 8.INSTALL FRONT FLOOR CARPET ASSEMBLY

a.

Return the front floor carpet assembly to its original position.


b.

Engage the 2 clamps.


c.

Install the 2 clips.


Hide 9.CONNECT CABLE TO NEGATIVE AUXILIARY BATTERY TERMINAL

Hide 58441L 10.INSTALL BATTERY SERVICE HOLE COVER

Hide 58849 12.INSTALL NO. 2 CONSOLE BOX HOLE COVER (w/o Rear Seat Entertainment System)

Hide 58912B 13.INSTALL REAR CONSOLE LOWER BOX

Hide 16.PERFORM INITIALIZATION

a.

Perform "Inspection After Repair" after replacing the fuel pump.

Click hereEngine / Hybrid System>A25A-FXS, A25B-FXS (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION