Home › Brake › BRAKE SYSTEM (OTHER) › BRAKE BOOSTER (for HV Model LHD)
RM37A0E _54 Brake _086869 BRAKE SYSTEM (OTHER) _0420924 BRAKE BOOSTER(for HV Model LHD) A

BRAKE SYSTEM (OTHER)  BRAKE BOOSTER(for HV Model LHD)  INSTALLATION  


CAUTION / NOTICE / HINT

NOTICE:
C426238C01
0.344,1.688 0.781,1.521 false 2.771,1.271 3.031,1.458 3.031,1.458 2.573,1.292 true 2.823,0.521 3.042,0.333 false 0.198,0.969 0.313,0.75 false 2.344,1.844 2.781,1.917 false 0.594,0.573 0.26,0.302 false 1.24,0.25 0.885,0.177 false 2.135,0.302 2.469,0.188 false 0.188,1.604 0.531,1.792 0.344,0.188 10 false *1 3.063,1.385 3.365,1.667 0.302,0.281 10 false *2 0.115,0.979 0.448,1.302 0.333,0.323 10 false *3 0.104,0.219 0.427,0.49 0.323,0.271 10 false *4 3.073,0.24 3.406,0.5 0.333,0.26 10 false *5 2.823,1.844 3.208,2.052 0.385,0.208 10 false *6 0.729,0.094 1.083,0.333 0.354,0.24 10 false *7 2.5,0.104 2.854,0.344 0.354,0.24 10 false *8
*1 No. 1 Skid Control ECU
*2 Reservoir Hose
*3 Master Cylinder Push Rod Clevis
*4 Boot
*5 Reservoir
*6 No. 1 Brake Actuator Tube
*7 No. 1 Wire Clamp Bracket
*8 Brake Booster with Accumulator Pump Assembly


Do not carry the brake master cylinder with pump assembly by the parts shown in the illustration.


PROCEDURE

Hide 47942 1.INSTALL NO. 2 BRAKE POWER SUPPLY BRACKET

a.

Using a 5 mm long hexagon socket wrench, install the No. 2 brake power supply bracket with the 2 bolts.

Torque:
6.5 N*m (66 kgf*cm, 58 in.*lbf)


Hide 47943 2.INSTALL NO. 3 BRAKE POWER SUPPLY BRACKET

a.

Using a 5 mm long hexagon socket wrench, install the No. 3 brake power supply bracket with the 2 bolts.

Torque:
6.5 N*m (66 kgf*cm, 58 in.*lbf)


Hide 3.INSTALL NO. 2 WIRE CLAMP BRACKET

a.

Using a 5 mm long hexagon socket wrench, install the No. 2 wire clamp bracket with the bolt.

Torque:
6.5 N*m (66 kgf*cm, 58 in.*lbf)


Hide 4.INSTALL NO. 1 WIRE CLAMP BRACKET

a.

Using a 5 mm long hexagon socket wrench, install the No. 1 wire clamp bracket with the bolt.

Torque:
6.5 N*m (66 kgf*cm, 58 in.*lbf)


Hide 47070B 5.INSTALL BRAKE BOOSTER WITH ACCUMULATOR PUMP ASSEMBLY

Hide 44551C 6.INSTALL NO. 1 BRAKE ACTUATOR TUBE

a.
C426244C01
2.729,3.115 2.729,2.698 false 1.792,2.969 2.292,3.229 0.5,0.26 10 false *a 2.667,3.125 3.021,3.344 0.354,0.219 10 false *b
*a Torque Wrench Fulcrum Length
*b Union Nut Wrench


Using a union nut wrench, install the No. 1 brake actuator tube.

Torque:
Specified tightening torque : 15.2 N*m (155 kgf*cm, 11 ft.*lbf)

NOTICE:
·

Do not kink or damage the brake line.

·

Do not allow any foreign matter such as dirt or dust to enter the brake line from the connecting parts.



HINT:
·

Calculate the torque wrench reading when changing the fulcrum length of the torque wrench.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

When using a union nut wrench (fulcrum length of 22 mm (0.866 in.)) + torque wrench (fulcrum length of 162 mm (6.38 in.)):

13.4 N*m (137 kgf*cm, 10 ft.*lbf)




Hide 47234L 7.INSTALL NO. 1 RESERVOIR HOSE

a.
C426242C01
2.281,0.75 0.542,0.385 0.542,0.385 1.583,1.26 true 1.792,2.313 2.104,2.51 0.313,0.198 10 false *b 1.781,2.938 2.094,3.135 0.313,0.198 10 false *b 0.385,0.271 0.698,0.469 0.313,0.198 10 false *a
*a Paint Mark
*b 90°
V100136

Front of the Vehicle


Install the No. 1 reservoir hose, and slide the 2 clips to secure it.

NOTICE:
·

Make sure that the paint mark is facing the front of the vehicle.

·

Install the clip within the range shown in the illustration.




Hide 47235G 8.INSTALL NO. 2 RESERVOIR HOSE

a.
C426240C01
0.698,2.333 1.208,2.167 true 2.156,2.948 2.667,2.781 true 0.542,2.25 0.854,2.448 0.313,0.198 10 false *a 2.698,2.698 3.01,2.896 0.313,0.198 10 false *a 1.74,0.417 2.052,0.615 0.313,0.198 10 false *b 1.771,1.167 2.083,1.365 0.313,0.198 10 false *b 1.781,3.604 2.094,3.802 0.313,0.198 10 false *b 2.625,3.604 2.938,3.802 0.313,0.198 10 false *b
*a Paint Mark
*b 90°
V100136

Front of the Vehicle
V100137

Up


Install the No. 2 reservoir hose, and slide the 2 clips to secure it.

NOTICE:
·

Make sure that the paint mark is facing the front of the vehicle (Upper Side).

·

Make sure that the paint mark is facing up (Lower Side).

·

Install the clip within the range shown in the illustration.




Hide 44785 9.INSTALL BRAKE BOOSTER GASKET

a.

Install a new brake booster gasket to the brake master cylinder with pump assembly.


Hide 10.INSTALL BRAKE MASTER CYLINDER WITH PUMP ASSEMBLY

a.

Install the brake master cylinder with pump assembly with the 4 nuts.

Torque:
12.7 N*m (130 kgf*cm, 9 ft.*lbf)

NOTICE:
·

Do not apply excessive force to the brake lines.

·

Be careful not to allow brake fluid to enter the connector.

·

If installing a new brake master cylinder with pump assembly, do not remove the hole plugs before connecting the brake lines because the brake booster with master cylinder assembly is filled with brake fluid.




Hide 47264A 11.INSTALL PUSH ROD PIN

a.
C319792C01
0,0 0,0 false
V100144

Lithium Soap Base Glycol Grease


Apply lithium soap base glycol grease to the push rod pin.


b.
C426236

Connect the master cylinder push rod clevis to the brake pedal support assembly with the push rod pin, and install a new clip as shown in the illustration.

HINT:

The push rod pin can be installed in either direction.



Hide 47101A 12.INSTALL BRAKE PEDAL RETURN SPRING

a.
C426791C01
0,0 0,0 false
V100136

Up
V100137

Front of the Vehicle


Install the brake pedal return spring to the brake pedal support assembly.

NOTICE:

Attach the bottom part of the brake pedal return spring first, making sure that the open part of the hook is facing the front of the vehicle. Attach the top part of the brake pedal return spring second, making sure that the open part of the hook is facing the rear of the vehicle.



Hide 84340 13.INSTALL STOP LIGHT SWITCH ASSEMBLY

Hide 14.CONNECT BRAKE LINE

a.
C426250C01
2.74,3.104 2.74,2.688 false 1.781,2.969 2.094,3.167 0.313,0.198 10 false *a 2.677,3.115 2.99,3.313 0.313,0.198 10 false *b
*a Torque Wrench Fulcrum Length
*b Union Nut Wrench


Using a union nut wrench, connect the 2 brake lines to the brake master cylinder with pump assembly.

Torque:
Specified tightening torque : 19.5 N*m (199 kgf*cm, 14 ft.*lbf)

NOTICE:
·

Do not kink or damage the brake lines.

·

Do not allow the brake lines to twist or interfere with other parts or the vehicle body during tightening.

·

Do not allow any foreign matter such as dirt or dust to enter the brake lines from the connecting parts.



HINT:
·

Calculate the torque wrench reading when changing the fulcrum length of the torque wrench.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

When using a union nut wrench (fulcrum length of 20 mm (0.787 in.)) + torque wrench (fulcrum length of 162 mm (6.38 in.)):

17.4 N*m (177 kgf*cm, 13 ft.*lbf)




Hide 15.CONNECT RESERVOIR HOSE

a.
C426251C01
1.438,2.49 1.885,2.969 1.885,2.969 1.844,2.198 true 1.833,3 2.01,3.167 0.177,0.167 10 true *a 0.49,0.563 0.667,0.729 0.177,0.167 10 true *b 1.25,0.563 1.427,0.729 0.177,0.167 10 true *b 2.177,0.563 2.354,0.729 0.177,0.167 10 true *b 2.677,0.458 2.854,0.625 0.177,0.167 10 true *c
*a Paint Mark
*b 90°
*c 30°
V100136

Up


Connect the 2 reservoir hoses to the brake master cylinder with pump assembly and slide the 2 clips to secure them.

NOTICE:
·

Make sure that the paint mark is facing up.

·

Install the clip within the range shown in the illustration.




Hide 82111 16.CONNECT ENGINE ROOM MAIN WIRE

a.

Install the engine room main wire to the vehicle body with bolt.

Torque:
8.0 N*m (82 kgf*cm, 71 in.*lbf)


b.
C426252C01
0,0 0,0 false
V113147

Connect the connector
V113148

Lock the lock lever


Engage the clamp to the brake master cylinder with pump assembly.


c.

Connect the connector to the brake master cylinder with pump assembly and lock the lock lever.

NOTICE:
·

Make sure that the connector is locked securely.

·

Make sure that the connector can be connected smoothly.

·

Do not allow water, oil or dirt to enter the connector.




d.
C426232

Connect the connector to the brake master cylinder with pump assembly.

NOTICE:

Do not allow water, oil or dirt to enter the connector.



Hide 17.FILL RESERVOIR WITH BRAKE FLUID

Hide 73900 18.INSTALL LOWER NO. 1 INSTRUMENT PANEL AIRBAG ASSEMBLY

Hide 55045 20.INSTALL LOWER INSTRUMENT PANEL FINISH PANEL SUB-ASSEMBLY

Hide 53601 21.CONNECT HOOD LOCK CONTROL LEVER SUB-ASSEMBLY

Hide 24.INSPECT AND ADJUST BRAKE PEDAL

Hide 55606 25.INSTALL NO. 1 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY

Hide 62112A 26.INSTALL COWL SIDE TRIM SUB-ASSEMBLY LH

Hide 67914 27.INSTALL FRONT DOOR SCUFF PLATE LH

Hide 55704B 28.INSTALL COWL VENTILATOR PANEL SUB-ASSEMBLY

Hide 29.INSTALL FRONT UPPER SUSPENSION TO COWL BRACE SUB-ASSEMBLY LH

Hide 53607B 30.INSTALL FRONT UPPER SUSPENSION TO COWL BRACE SUB-ASSEMBLY RH

HINT:

Perform the same procedure as for the LH side.


Hide 53892C 31.INSTALL FRONT FENDER SPLASH SHIELD SEAL FRONT LH

Hide 53891C 32.INSTALL FRONT FENDER SPLASH SHIELD SEAL FRONT RH

HINT:

Perform the same procedure as for the LH side.


Hide 53808A 33.INSTALL FENDER SPLASH SHIELD SUB-ASSEMBLY REAR LH

Hide 53807A 34.INSTALL FENDER SPLASH SHIELD SUB-ASSEMBLY REAR RH

HINT:

Perform the same procedure as for the LH side.


Hide 35.INSTALL WINDSHIELD WIPER MOTOR AND LINK ASSEMBLY

Hide 36.PERFORM INITIALIZATION AND CALIBRATION