Home › Suspension › REAR SUSPENSION › REAR SUSPENSION MEMBER (for Gasoline Model) › 2020.02–2020.11
RM37A0E _53 Suspension _086866 REAR SUSPENSION _0417445 REAR SUSPENSION MEMBER(for Gasoline Model) A

REAR SUSPENSION  REAR SUSPENSION MEMBER(for Gasoline Model)  REMOVAL  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed and installed, or replaced during rear suspension member sub-assembly removal/installation are shown below.

Necessary Procedures After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link
Rear wheel alignment adjustment
1.

Perform "Reset Memory".

2.

Perform "Calibration".


·

VSC is disabled or malfunctions

·

DTCs are output

·

Slip indicator light illuminates

·

ABS warning light illuminates


(Click here)
Suspension, tires, etc.
(The vehicle height changes because of suspension or tire replacement)
·

Measurement of ultrasonic sensor detection angle

·

Ultrasonic sensor detection angle registration


Parking Support Brake System (Click here)
Rear television camera assembly optical axis (Back camera position setting) Parking Assist Monitor System (Click here)
·

Parking assist ECU initialization

·

Adjust steering angle


Panoramic View Monitor System (Click here)
Gas leak from exhaust system is repaired Perform Inspection After Repair
·

Poor idle, etc.

·

Engine start function, etc.


(Click here)

CAUTION:
A344784

To prevent burns, do not touch the engine, exhaust pipe or other high temperature components while the engine is hot.


PROCEDURE

Hide 1.REMOVE REAR WHEEL

Hide 17430 2.REMOVE TAIL EXHAUST PIPE ASSEMBLY

Hide 37100 3.REMOVE PROPELLER WITH CENTER BEARING SHAFT ASSEMBLY

Hide 48738 4.REMOVE REAR SUSPENSION ARM COVER LH

Hide 48737 5.REMOVE REAR SUSPENSION ARM COVER RH

HINT:

Perform the same procedure as for the LH side.


Hide 42312B 6.REMOVE REAR AXLE SHAFT NUT LH

Hide 42311N 7.REMOVE REAR AXLE SHAFT NUT RH

HINT:

Perform the same procedure as for the LH side.


Hide 47319F 8.SEPARATE REAR FLEXIBLE HOSE LH

a.
C424684

Remove the bolt and separate the rear flexible hose LH from the rear upper control arm assembly LH.


Hide 47318F 9.SEPARATE REAR FLEXIBLE HOSE RH

HINT:

Perform the same procedure as for the LH side.


Hide 890C0A 10.DISCONNECT NO. 2 PARKING BRAKE WIRE ASSEMBLY

a.
C424674C01
1.281,0.969 1.729,0.969 true 1.021,0.885 1.25,1.063 0.229,0.177 10 true *a
*a Protective Tape


Using a screwdriver with its tip wrapped with protective tape, disconnect the No. 2 parking brake wire assembly connector from the rear skid control sensor.

NOTICE:
·

Remove any dirt or foreign matter on and around the No. 2 parking brake wire assembly connector before performing this step.

·

Do not allow water, oil or dirt to enter the No. 2 parking brake wire assembly connector.

·

Be careful not to damage the rear skid control sensor or connector cover.




Hide 890C0 11.DISCONNECT NO. 1 PARKING BRAKE WIRE ASSEMBLY

HINT:

Perform the same procedure as for the LH side.


Hide 89544E 12.REMOVE REAR SKID CONTROL SENSOR LH

Hide 89544D 13.REMOVE REAR SKID CONTROL SENSOR RH

HINT:

Perform the same procedure as for the LH side.


Hide 14.REMOVE REAR STABILIZER LINK ASSEMBLY LH

Hide 15.REMOVE REAR STABILIZER LINK ASSEMBLY RH

HINT:

Perform the same procedure as for the LH side.


Hide 48812 16.REMOVE REAR STABILIZER BAR

Hide 48835 17.REMOVE REAR LOWER STABILIZER BRACKET

Hide 48231B 18.REMOVE REAR COIL SPRING LH

Hide 48231A 19.REMOVE REAR COIL SPRING RH

HINT:

Perform the same procedure as for the LH side.


Hide 48258C 20.REMOVE REAR LOWER COIL SPRING INSULATOR LH

Hide 48258B 21.REMOVE REAR LOWER COIL SPRING INSULATOR RH

HINT:

Perform the same procedure as for the LH side.


Hide 48740F 22.REMOVE REAR NO. 2 SUSPENSION ARM ASSEMBLY LH

Hide 48730F 23.REMOVE REAR NO. 2 SUSPENSION ARM ASSEMBLY RH

HINT:

Perform the same procedure as for the LH side.


Hide 48720A 24.REMOVE REAR NO. 1 SUSPENSION ARM ASSEMBLY LH

Hide 48710A 25.REMOVE REAR NO. 1 SUSPENSION ARM ASSEMBLY RH

HINT:

Perform the same procedure as for the LH side.


Hide 48790 26.SEPARATE REAR UPPER CONTROL ARM ASSEMBLY LH

a.
C426727

Remove the bolt and nut and separate the rear upper control arm assembly LH from the rear axle carrier sub-assembly LH.

NOTICE:

Because the nut has its own stopper, do not turn the nut. Loosen the bolt with the nut secured.



Hide 48770A 27.SEPARATE REAR UPPER CONTROL ARM ASSEMBLY RH

HINT:

Use the same procedure as for the LH side.


Hide 28.DRAIN DIFFERENTIAL OIL

for Dynamic Torque Control AWD: Click hereGeneral>MAINTENANCE>DIFFERENTIAL OIL>REPLACEMENT

for Dynamic Torque Vectoring AWD: Click hereGeneral>MAINTENANCE>DIFFERENTIAL OIL>REPLACEMENT

Hide 42330 30.REMOVE REAR DRIVE SHAFT ASSEMBLY RH

HINT:

Use the same procedure as for the LH side.


Hide 42341C 31.REMOVE REAR DRIVE SHAFT LH SNAP RING

Hide 42341B 32.REMOVE REAR DRIVE SHAFT RH SNAP RING

HINT:

Use the same procedure as for the LH side.


Hide 41110 33.REMOVE REAR DIFFERENTIAL CARRIER ASSEMBLY (for Dynamic Torque Control AWD)

Hide 41110 34.REMOVE TORQUE VECTORING DIFFERENTIAL CARRIER ASSEMBLY (for Dynamic Torque Vectoring AWD)

Hide 41651 35.REMOVE REAR NO. 1 DIFFERENTIAL MOUNT CUSHION

Hide 82164 36.SEPARATE FRAME WIRE

a.
C426734

Remove the bolt and disengage the clamp to separate the frame wire from the rear suspension member sub-assembly.


Hide 51206A 37.REMOVE REAR SUSPENSION MEMBER SUB-ASSEMBLY

a.
C426728C01
2.865,3.854 2.865,3.698 2.865,3.698 3,3.698 false 0.677,4.417 0.677,4.01 false 1.656,4.406 1.656,4.031 false 2.104,3.906 2.5,3.177 2.5,3.177 2.635,3.177 true 2.427,4.427 2.427,3.917 false 3.042,3.625 3.354,3.781 0.313,0.156 10 false *a 0.615,4.438 0.927,4.594 0.313,0.156 10 false *b 2.396,4.438 2.708,4.594 0.313,0.156 10 false *c 1.583,4.406 1.792,4.594 0.208,0.188 10 false *c 2.677,3.063 2.896,3.26 0.219,0.198 10 true *b
*a Engine Lifter
*b Attachment
*c Wooden Block
V100155

Attachment and Wooden Block Placement Location


Using an engine lifter, 2 attachments and 2 wooden blocks or equivalent tools, support the rear suspension member sub-assembly as shown in the illustration.

CAUTION:
C426729

·

The rear suspension member sub-assembly is a very heavy component. Make sure that it is supported securely.

·

If the rear suspension member sub-assembly is not securely supported, it may drop, resulting in serious injury.



NOTICE:

Use attachments and wooden blocks to keep the rear suspension member sub-assembly level.



b.

Remove the 4 bolts, 2 nuts, 2 rear lower suspension braces, rear lower suspension member stopper LH and rear lower suspension member stopper RH.


c.

Slowly lower the rear suspension member sub-assembly.

NOTICE:

When lowering the rear suspension member sub-assembly, be careful not to damage the vehicle body or other components installed to the vehicle.



Hide 52272 38.REMOVE REAR SUSPENSION MEMBER UPPER STOPPER

a.
C426730

Remove the 2 rear suspension member upper stoppers from the rear suspension member sub-assembly.


Hide 52278A 39.REMOVE REAR SUSPENSION MEMBER LOWER STOPPER RETAINER

a.
C426731

Remove the 2 rear suspension member lower stopper retainers from the rear suspension member sub-assembly.


Hide 48790 40.REMOVE REAR UPPER CONTROL ARM ASSEMBLY LH

Hide 48770A 41.REMOVE REAR UPPER CONTROL ARM ASSEMBLY RH

HINT:

Perform the same procedure as for the LH side.


Hide 52271D 42.REMOVE REAR SUSPENSION MEMBER FRONT BODY MOUNTING CUSHION (for LH Side)

a.
C427655C01
1.667,0.333 1.26,0.333 false 2.531,1.167 2.125,1.167 true 1.063,0.271 1.281,0.5 0.219,0.229 10 false *a 2.594,1.094 2.792,1.26 0.198,0.167 10 false *a
*a Bend Portion


Using a chisel and hammer, bend the 2 portions of the rear suspension member front body mounting cushion rib.

NOTICE:

Make sure to bend the 2 portions of the cushion rib until the claws of SST can fit securely.



b.
C199891N11
2.323,0.313 2.625,0.313 false 1.188,1.563 1.656,1.563 true 2.667,0.24 2.979,0.448 0.313,0.208 10 false SST 0.896,1.49 1.208,1.729 0.313,0.24 10 false SST

Install SST as shown in the illustration.

SST
09830-10010  (09830-01010, 09830-01040, 09830-01050)
09950-40011  (09951-04020, 09952-04010, 09954-04010, 09955-04051, 09958-04011)

NOTICE:

Apply molybdenum grease to the threads and tip of the SST center bolt before use.



c.
C199893C05
1.115,0.594 0.771,0.594 false 1.906,1.417 1.646,1.417 false 0.5,0.531 0.844,0.76 0.344,0.229 10 false SST 1.958,1.344 2.406,1.552 0.448,0.208 10 false SST 3.052,0.802 3.365,0.958 0.313,0.156 10 false *a 2.25,1.969 2.563,2.125 0.313,0.156 10 false *b
*a Hold
*b Turn


Using SST, remove the rear suspension member front body mounting cushion while applying lubricant into the clearance between the rear suspension member front body mounting cushion and the rear suspension member sub-assembly.

SST
09830-10010  (09830-01010, 09830-01040, 09830-01050)
09950-40011  (09951-04020, 09952-04010, 09954-04010, 09955-04051, 09958-04011)

NOTICE:
·

Set the claws of SST onto the rear suspension member sub-assembly securely as shown in the illustration.

·

Tighten SST slowly and evenly.

·

Be careful as the rear suspension member front body mounting cushion may fly out.

·

The rear suspension member front body mounting cushion cannot be reused.




d.

Remove SST and the rear suspension member front body mounting cushion (LH Side) from the rear suspension member sub-assembly.


Hide 52271D 43.REMOVE REAR SUSPENSION MEMBER FRONT BODY MOUNTING CUSHION (for RH Side)

HINT:

Perform the same procedure as for the LH side.


Hide 52276A 44.REMOVE REAR SUSPENSION MEMBER REAR BODY MOUNT CUSHION LH

a.
C427656C01
2.438,0.927 2.729,0.927 false 1.656,1.896 1.948,1.896 false 2.792,0.844 3.125,1.125 0.333,0.281 10 false *a 1.469,1.813 1.688,2.021 0.219,0.208 10 false *a
*a Bend Portion


Using a chisel and hammer, bend the 2 portions of the rear suspension member rear body mount cushion LH rib.

NOTICE:

Make sure to bend the 2 portions of the cushion rib until the claws of SST can fit securely.



b.
C199892N15
2.156,1.583 1.865,1.583 false 1.229,0.323 0.938,0.323 false 2.219,1.51 2.667,1.76 0.448,0.25 10 false SST 0.646,0.25 0.979,0.542 0.333,0.292 10 false SST

Install SST as shown in the illustration.

SST
09830-10010  (09830-01010, 09830-01040, 09830-01050)
09950-40011  (09951-04020, 09952-04010, 09954-04010, 09955-04051, 09958-04011)

NOTICE:

Apply molybdenum grease to the threads and tip of the SST center bolt before use.



c.
C199894C06
1.24,0.594 0.844,0.594 true 2.094,1.417 1.792,1.417 false 0.583,0.531 0.938,0.729 0.354,0.198 10 true SST 2.146,1.344 2.542,1.552 0.396,0.208 10 false SST 3.01,0.958 3.323,1.115 0.313,0.156 10 false *a 2.49,1.958 2.802,2.115 0.313,0.156 10 false *b
*a Hold
*b Turn


Using SST, remove the rear suspension member rear body mount cushion LH while applying lubricant into the clearance between the rear suspension member rear body mount cushion LH and the rear suspension member sub-assembly.

SST
09830-10010  (09830-01010, 09830-01040, 09830-01050)
09950-40011  (09951-04020, 09952-04010, 09954-04010, 09955-04051, 09958-04011)

NOTICE:
·

Set the claws of SST onto the rear suspension member sub-assembly securely as shown in the illustration.

·

Tighten SST slowly and evenly.

·

Be careful as the rear suspension member rear body mount cushion LH may fly out.

·

The rear suspension member rear body mount cushion LH cannot be reused.




d.

Remove SST and the rear suspension member rear body mount cushion LH from the rear suspension member sub-assembly.


Hide 52275B 45.REMOVE REAR SUSPENSION MEMBER REAR BODY MOUNT CUSHION RH

HINT:

Perform the same procedure as for the LH side.


Hide 46.REMOVE HOLE PLUG

a.
C336837

Remove the 13 hole plugs from the rear suspension member sub-assembly as shown in the illustration.