Home › Engine / Hybrid System › A25A-FXS, A25B-FXS (FUEL) › FUEL INJECTOR (for Port Injection) › from 2021.10
RM37A0E _51 Engine / Hybrid System _086907 A25A-FXS, A25B-FXS FUEL _0417782 FUEL INJECTOR(for Port Injection) A

A25A-FXS, A25B-FXS FUEL  FUEL INJECTOR(for Port Injection)  REMOVAL  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed and installed, or replaced during port fuel injector assembly removal/installation are shown below.

Necessary Procedures After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link

*1: Learning can also be performed using the GTS.

Click here(Click here)

Auxiliary battery terminal is disconnected/reconnected Perform steering sensor zero point calibration Lane Control System (Click here)
Parking Support Brake System*1
Pre-collision System
Memorize steering angle neutral point Parking Assist Monitor System (Click here)
Panoramic View Monitor System (Click here)
Initialize back door lock Power Door Lock Control System (Click here)
Reset back door close position Power Back Door System (Click here)
Replacement of inverter with converter assembly Resolver learning
·

DTCs are stored

·

Slight vibration at a vehicle speed of 5 km/h (3 mph) or less

·

Shock or vibration during acceleration


for 2WD:(Click here)
for 4WD/AWD:(Click here)
Replacement of ECM Perform Vehicle Identification Number (VIN) registration DTC is output (Click here)
·

Replacement of port fuel injector assembly

·

Replacement of No. 2 fuel pressure sensor

·

Replacement of fuel pump assembly

·

Replacement of throttle body with motor assembly

·

Cleaning the deposits from the throttle body with motor assembly

·

Replacement of EGR valve assembly

·

Gas leak from exhaust system is repaired


Perform Inspection After Repair
·

Poor idle, etc.

·

Engine start function, etc.


(Click here)

CAUTION:
·
A360563

Never perform work on fuel system components near any possible ignition sources.

·

Vaporized fuel could ignite, resulting in a serious accident.

·
A360564

Do not perform work on fuel system components without first disconnecting the cable from the negative (-) auxiliary battery terminal.

·

Sparks could cause vaporized fuel to ignite, resulting in a serious accident.

·
A357489

To prevent serious injury due to fuel spray from the high-pressure fuel lines, always discharge fuel system pressure before removing any fuel system components.



NOTICE:
·

After the ignition switch is turned off, the radio and display receiver assembly or the radio receiver assembly records various types of memory and settings. As a result, after turning the ignition switch off, make sure to wait at least 120 seconds before disconnecting the cable from the negative (-) auxiliary battery terminal.

·

This procedure includes the removal of small-head bolts. Refer to Small-Head Bolts of Basic Repair Hint to identify the small-head bolts.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION



PROCEDURE

Hide 1. PRECAUTION

NOTICE:

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.


Hide 58441L 3.REMOVE BATTERY SERVICE HOLE COVER

Hide 4.DISCONNECT CABLE FROM NEGATIVE AUXILIARY BATTERY TERMINAL

Hide 22030 5.REMOVE THROTTLE BODY WITH MOTOR ASSEMBLY

Hide 25715 7.REMOVE EMISSION CONTROL VALVE BRACKET (w/ Differential Pressure Sensor)

Hide 23910A 9.DISCONNECT FUEL TUBE SUB-ASSEMBLY

a.
A403914

Remove the fuel pipe clamp from the fuel tube connector.


b.
A455295

Disconnect the fuel tube sub-assembly from the fuel pump assembly and fuel delivery pipe sub-assembly.

Click hereEngine / Hybrid System>A25A-FXS, A25B-FXS (FUEL)>FUEL SYSTEM>PRECAUTION


Hide 23801P 10.REMOVE NO. 1 FUEL PIPE SUB-ASSEMBLY

CAUTION:

To prevent serious injury due to fuel spray from the high-pressure fuel lines, always discharge fuel system pressure before removing any fuel system components.


a.
A428387

Disconnect the ignition coil connector.


b.

for EGR Valve Bracket Connection Type:

i.
A455296

Using a 17 mm union nut wrench, loosen the 2 union nuts of the No. 1 fuel pipe sub-assembly.



c.

for Cylinder Head Cover Sub-assembly Connection Type:

i.
A474162C01
0,0 0,0 false
V100135

Union Nut
V100136

Bolt


Using a 17 mm union nut wrench, loosen the 2 union nuts of the No. 1 fuel pipe sub-assembly.


ii.

Using an 8 mm socket wrench, remove the bolt.



d.
A455297

Loosen the 2 bolts of the fuel pump assembly.


e.

Remove the No. 1 fuel pipe sub-assembly from the fuel delivery pipe and fuel pump assembly.


Hide 23100X 11.REMOVE FUEL (ENGINE ROOM SIDE) PUMP ASSEMBLY

Hide 23807 12.REMOVE FUEL DELIVERY PIPE SUB-ASSEMBLY

a.
A403916

Disconnect the No. 5 engine wire connector.


b.
A405310

Remove the 2 bolts and fuel delivery pipe sub-assembly with the 4 port fuel injector assemblies from the cylinder head sub-assembly.

NOTICE:

Be careful not to drop the port fuel injector assemblies when removing the fuel delivery pipe sub-assembly.



Hide 23807V 13.REMOVE NO. 1 DELIVERY PIPE SPACER

a.
A403917

Remove the 2 No. 1 delivery pipe spacers from the cylinder head sub-assembly.


Hide 23291 14.REMOVE INJECTOR VIBRATION INSULATOR

a.
A403918

Remove the 4 injector vibration insulators from the cylinder head sub-assembly.


Hide 82125N 15.REMOVE NO. 5 ENGINE WIRE

a.
A401651

Disconnect the 4 port fuel injector assembly connectors and No. 2 fuel pressure sensor connector.


b.

Disengage the 2 clamps to remove the No. 5 engine wire from the fuel delivery pipe sub-assembly.


Hide 23250F 16.REMOVE PORT FUEL INJECTOR ASSEMBLY

a.
A401652

Pull the 4 port fuel injector assemblies out of the fuel delivery pipe sub-assembly.


b.
A401653

Remove the O-ring from each port fuel injector assembly.


c.
A401654N01
2,0.417 2.771,0.615 0.771,0.198 10 false No. 1

Attach a tag or label with the corresponding cylinder number to each port fuel injector assembly so that they can be installed to their original locations.

NOTICE:

Cover the port fuel injector assemblies with plastic bags to prevent damage and contamination.