2014 Hilux · Service Manual TRANSMISSION

REMOVAL

Removal / installation · Vehicles built Aug 2012 – Jul 2013

Versions by build date: Jun 2011 – Jul 2012 Aug 2012 – Jul 2013 from Aug 2013


1. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

CAUTION:
Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to prevent airbag and seat belt pretensioner activation.


2. REMOVE CONSOLE BOX ASSEMBLY
(Click here)

3. REMOVE SHIFT LEVER BOOT ASSEMBLY

G034544E02
  1. w/o Console Box:
    Remove the front seat, front door scuff plate, etc. and fold back the floor carpet so that the shift lever can be removed.

  1. Remove the 4 screws, 2 clips and shift lever boot.


4. REMOVE FLOOR SHIFT SHIFT LEVER ASSEMBLY

G021695E02
  1. Cover the shift lever cap with a cloth.

  1. Press down on the shift lever cap and rotate it counterclockwise to remove it.

  1. Pull out the shift lever.


5. REMOVE TRANSFER HIGH AND LOW SHIFT LEVER ASSEMBLY

G021696E02
  1. Using needle nose pliers, remove the snap ring and pull out the shift lever.

    HINT:
    Move the transfer shift lever to the H4 position.


6. REMOVE TRANSFER CASE LOWER PROTECTOR
  1. Remove the 4 bolts and transfer case lower protector.


7. REMOVE NO. 1 ENGINE UNDER COVER

8. REMOVE NO. 2 ENGINE UNDER COVER

9. REMOVE NO. 3 ENGINE UNDER COVER

10. DRAIN MANUAL TRANSMISSION OIL
  1. Remove the drain plug and gasket to drain the oil.

  1. Install a new gasket and the drain plug.

    Torque:
    37 N*m{ 377 kgf*cm , 27 ft.*lbf }


11. REMOVE REAR PROPELLER SHAFT ASSEMBLY
for TSAM Made: (Click here)
for TMT Made: (Click here)

12. REMOVE FRONT PROPELLER SHAFT ASSEMBLY
for TSAM Made: (Click here)
for TMT Made: (Click here)

13. REMOVE FRONT EXHAUST PIPE ASSEMBLY
for 2TR-FE: (Click here)
for 1GR-FE: (Click here)
for 1KD-FTV: (Click here)
for 1KD-FTV for DPF: (Click here)
for 2KD-FTV: (Click here)
for 2KD-FTV for DPF: (Click here)

14. DISCONNECT WIRE HARNESS
  1. Transmission side:
    Disconnect the back-up light switch connector.

  1. Transfer side:
    Disconnect the No. 1, No. 2 and No. 3 transfer indicator switch connectors, and vehicle speed sensor connector.


15. DISCONNECT CLUTCH RELEASE CYLINDER ASSEMBLY (for 1KD-FTV, 2KD-FTV, 2TR-FE)

G034223E01
  1. Remove the 2 bolts and disconnect the release cylinder.


16. REMOVE CLUTCH RELEASE CYLINDER ASSEMBLY (for 1GR-FE)

C112617
  1. Remove the bolts, nut and release cylinder heat insulator.

  1. C112615
    Using a union nut wrench, remove the flexible tube.

    HINT:
    Use a container to catch the fluid.

  1. C112616
    Disconnect the clutch release cylinder to flexible hose tube.

  1. Remove the bolt and 2 way.

  1. C112662
    Remove the 2 bolts and the release cylinder.

  1. D030415
    Using a union nut wrench, disconnect the 2 flexible hose tubes.


17. REMOVE STARTER ASSEMBLY
for 2TR-FE 1.4 kW Type: (Click here)
for 2TR-FE 1.7 kW Type: (Click here)
for 1GR-FE: (Click here)
for 1KD-FTV 2.2 kW Type Bosch Made: (Click here)
for 1KD-FTV 2.2 kW Type Denso Made: (Click here)
for 1KD-FTV 2.7 kW Type: (Click here)
for 2KD-FTV 2.0 kW Type: (Click here)
for 2KD-FTV 2.2 kW Type: (Click here)
for 2KD-FTV 2.7 kW Type: (Click here)

18. REMOVE NO. 3 FRAME CROSSMEMBER SUB-ASSEMBLY

G034218E03
  1. Support the transmission rear side with a support stand.

  1. Remove the 4 set bolts of the No. 1 engine mounting insulator rear.

  1. Remove the 4 bolts, 4 nuts and frame crossmember.


19. REMOVE REAR NO. 1 ENGINE MOUNTING INSULATOR

G034219E03
  1. Remove the 4 bolts and engine mounting insulator.


20. REMOVE EXHAUST MANIFOLD STAY (for 2TR-FE)

B086194E01
  1. Remove the 3 bolts and exhaust manifold stay.


21. REMOVE STIFFENER PLATE (for 1KD-FTV, 2KD-FTV)

G034607E01
  1. Remove the 4 bolts and stiffener plate RH.

  1. Remove the 4 bolts and stiffener plate LH.


22. REMOVE MANUAL TRANSMISSION UNIT ASSEMBLY

C113299E01
  1. Using a transmission jack, support the transmission.

  1. Remove the support stand from the rear side.

  1. for 1KD-FTV, 2KD-FTV:
    Remove the 5 bolts and transmission.

  1. for 2TR-FE:
    Remove the 7 bolts and transmission.

  1. for 1GR-FE:
    Remove the 9 bolts and transmission.


23. REMOVE TRANSFER ASSEMBLY
(Click here)
← REMOVAL (Jun 2011 – Jul 2012)REMOVAL (from Aug 2013) →