Home › Engine / Hybrid System › 1KD-FTV ENGINE MECHANICAL › CAMSHAFT(w/o Glow Plug Controller)
RM1840EF _51 Engine / Hybrid System _009573 1KD-FTV ENGINE MECHANICAL _0052147 CAMSHAFT(w/o Glow Plug Controller) A

1KD-FTV ENGINE MECHANICAL  CAMSHAFT(w/o Glow Plug Controller)  INSTALLATION  


CAUTION / NOTICE / HINT

NOTICE:
·

When replacing the injectors (including shuffling the injectors between the cylinders), common rail or cylinder head, it is necessary to replace the injection pipes with new ones.

·

When replacing the fuel supply pump, common rail, cylinder block, cylinder head, cylinder head gasket or timing gear case, it is necessary to replace the fuel inlet pipe with a new one.

·

After removing the injection pipes, clean them with a brush and compressed air.



PROCEDURE

Hide 1.INSTALL CAMSHAFT

a.
G036616
0.573,1.635 1.177,1.792 1.177,1.792 1.25,1.792 true 0.125,1.156 0.458,1.344 0.333,0.188 10 false 90° 1.271,1.708 1.448,1.865 0.177,0.156 10 false *1
*1 Key


Using the crankshaft pulley bolt, set the No. 1 cylinder to 90° BTDC/compression.

HINT:

Set the No. 1 cylinder to 90° BTDC/compression to prevent the top of the piston from hitting against the valve head.



b.
A060149
0.365,0.542 1.021,0.344 1.021,0.344 1.125,0.344 true 0.344,0.021 0.531,0.188 0.188,0.167 10 false *a 1.146,0.26 1.323,0.417 0.177,0.156 10 false *1
*1 Key Groove
*a Upward


Install the camshafts.

i.

Apply engine oil to the thrust portion of the camshaft.


ii.

Place the camshaft on the cylinder head with the key groove facing upward.


iii.
A060150

Align the timing marks (1-dot marks) of the camshaft drive and driven main gears and set the No. 2 camshaft in place.



c.

Remove any old seal packing (FIPG material) from the camshaft bearing cap.


d.
A060283
0.906,1.417 0.906,1.74 true 1.635,0.844 1.281,0.438 1.281,0.438 1.198,0.438 false 2.792,0.813 2.542,0.531 2.542,0.531 2.365,0.531 true 0.813,1.76 1,1.927 0.188,0.167 10 false *2 2.375,0.25 3.417,0.427 1.042,0.177 10 false 8 mm (0.315 in.) 0.99,0.323 1.177,0.49 0.188,0.167 10 false *1 2.167,0.448 2.354,0.615 0.188,0.167 10 false *1
*1 Seal Packing
*2 Oil Passage


Apply seal packing to the specified areas shown in the illustration.

Seal packing:

Toyota Genuine Seal Packing Black, Three Bond 1207B or equivalent


Standard seal diameter:

4 mm (0.157 in.)


NOTICE:
·

Do not allow seal packing to contact the oil passage of the bearing cap.

·

After applying seal packing, install the camshaft bearing caps within 3 minutes and tighten the bolts within 15 minutes.

·

Do not start the engine for at least 2 hours after installation.




e.
A060146

Install the 5 bearing caps to their proper locations.


f.
A060147
1.729,1.031 1.885,1.198 0.156,0.167 10 true 9 1.885,0.542 2.042,0.708 0.156,0.167 10 true 1 1.698,0.354 1.854,0.521 0.156,0.167 10 false 2 2.135,0.729 2.292,0.896 0.156,0.167 10 true 3 2.24,0.375 2.396,0.542 0.156,0.167 10 true 4 1.292,0.667 1.448,0.833 0.156,0.167 10 false 8 1.469,0.813 1.625,0.979 0.156,0.167 10 true 7 2.5,0.5 2.656,0.667 0.156,0.167 10 true 6 2.125,0.156 2.281,0.323 0.156,0.167 10 false 5 2.781,0.177 3.01,0.344 0.229,0.167 10 false 10 2.563,0.052 2.792,0.219 0.229,0.167 10 false 11 3.042,0.375 3.271,0.542 0.229,0.167 10 false 12 0.875,1.135 1.104,1.302 0.229,0.167 10 true 13 0.615,0.958 0.844,1.125 0.229,0.167 10 false 14 1.073,1.354 1.302,1.521 0.229,0.167 10 true 15

Apply a light coat of engine oil to the threads and under the heads of the bearing cap bolts.


g.

Install and uniformly tighten the 15 bearing cap bolts in several passes in the sequence shown in the illustration.

Torque:
19 N*m (194 kgf*cm, 14 ft.*lbf)


h.
A060145
1.854,0.771 1.063,0.771 true 0.719,0.688 1.052,0.854 0.333,0.167 10 false SST

Install a new camshaft oil seal.

i.

Apply MP grease to the lip of a new oil seal.


ii.

Using SST and a hammer, tap in the oil seal until its surface is flush with the surfaces of the camshaft bearing cap and cylinder head.

SST
09608-06041  



Hide 13.TEMPORARILY INSTALL ELECTRIC EGR CONTROL VALVE ASSEMBLY WITH NO. 2 EGR VALVE AND EGR COOLER (w/ EGR Cooler)

Hide 19.INSTALL NO. 2 INTAKE AIR CONNECTOR BRACKET (w/ EGR Cooler)

Hide 20.INSTALL ELECTRIC VACUUM REGULATING VALVE ASSEMBLY (w/ EGR Cooler)

Hide 22.INSTALL NO. 1, NO. 2 AND NO. 3 INJECTION PIPE SUB-ASSEMBLY

Hide 31.INSTALL RADIATOR HOSE INLET