Home › Engine / Hybrid System › 2KD-FTV ENGINE MECHANICAL › CYLINDER HEAD GASKET(w/o DPF) › from 2012.10
RM1840EF _51 Engine / Hybrid System _009574 2KD-FTV ENGINE MECHANICAL _0052168 CYLINDER HEAD GASKET(w/o DPF) A

2KD-FTV ENGINE MECHANICAL  CYLINDER HEAD GASKET(w/o DPF)  INSTALLATION  


CAUTION / NOTICE / HINT

NOTICE:
·

When replacing the injectors (including shuffling the injectors between the cylinders), common rail or cylinder head, it is necessary to replace the injection pipes with new ones.

·

When replacing the fuel supply pump, common rail, cylinder block, cylinder head, cylinder head gasket or timing gear case, it is necessary to replace the fuel inlet pipe with a new one.

·

After removing the injection pipes, clean them with a brush and compressed air.



PROCEDURE

Hide 1.INSTALL CYLINDER HEAD GASKET

a.
A301938
2.604,0.563 2.802,0.365 2.802,0.365 2.896,0.365 false 2.917,0.26 3.229,0.458 0.313,0.198 10 false *1 2.854,1.313 3.167,1.51 0.313,0.198 10 false *2
*1 Measuring Tip
*2 Protrusion


Check the piston protrusions for each cylinder.

i.

Clean the cylinder block with solvent.


ii.

Set the piston of the cylinder to be measured to slightly before TDC.


iii.

Place a dial indicator on the cylinder block, and position the measuring tip as shown in the illustration.


iv.

Set the dial indicator at 0 mm (0 in.)

HINT:

Make sure that the measuring tip is square to the cylinder block gasket surface and piston head when taking the measurements.




b.

Find where the piston head protrudes most by slowly turning the crankshaft clockwise and counterclockwise.


c.
A058134
1.219,1.896 1.594,2.083 0.375,0.188 10 false X: *1
*1 Measuring Point


Measure the piston protrusion of each cylinder at the 2 points shown in the illustration.


d.

For the piston protrusion value of each cylinder, use the average of the 2 measurements of each cylinder.

Standard piston protrusion:

0.005 to 0.255 mm (0.000197 to 0.0100 in.)


HINT:

When installing the piston and connecting rod assembly, if the protrusion is not as specified, remove the piston and connecting rod assembly and reinstall them.



e.
A060174
2.667,0.365 2.792,0.396 false 2.938,0.646 3,0.542 false 0.594,0.26 0.458,0.385 false 0.385,0.573 0.615,0.51 false 1.125,0.438 0.771,0.604 false 0.625,0.125 0.771,0.313 0.146,0.188 10 false A 1.5,0.531 1.708,0.719 0.208,0.188 10 false *1 2.75,1.26 2.958,1.448 0.208,0.188 10 false *1 0.26,0.51 0.406,0.698 0.146,0.188 10 false B 2.552,0.292 2.698,0.479 0.146,0.188 10 false D 1.146,0.333 1.292,0.521 0.146,0.188 10 false C 2.781,0.573 2.927,0.76 0.146,0.188 10 false E
*1 Cutout Mark


Select a new cylinder head gasket.

HINT:

New cylinder head gaskets are available in 5 sizes, and are marked A, B, C, D or E.


New Cylinder Head Gasket Thickness:
Mark Specified Condition
A 0.80 to 0.90 mm (0.0315 to 0.0354 in.)
B 0.85 to 0.95 mm (0.0335 to 0.0374 in.)
C 0.90 to 1.00 mm (0.0354 to 0.0394 in.)
D 0.95 to 1.05 mm (0.0374 to 0.0413 in.)
E 1.00 to 1.10 mm (0.0394 to 0.0433 in.)


i.

Select the largest piston protrusion value from the measurements made. Then select a new appropriate gasket according to the table below.

Gasket Size:
Item Specified Condition
Piston protrusion 0.005 to 0.054 mm (0.000197 to 0.00213 in.) 0.055 to 0.104 mm (0.00217 to 0.00409 in.) 0.105 to 0.154 mm (0.00413 to 0.00606 in.) 0.155 to 0.204 mm (0.00610 to 0.00803 in.) 0.205 to 0.255 mm (0.00807 to 0.0100 in.)
Gasket to be used A B C D E




f.
A060144
0.698,0.833 0.573,0.885 false
V100135

Front


Place the cylinder head gasket on the cylinder block.

NOTICE:

Make sure the gasket is installed facing the proper direction.



Hide 2.INSTALL CYLINDER HEAD SUB-ASSEMBLY

HINT:
·

The cylinder head bolts are tightened in 3 progressive steps.

·

If any bolt is broken or deformed, replace it.



a.

Place the cylinder head on the cylinder head gasket.


b.

Apply a light coat of engine oil to the threads and under the heads of the cylinder head bolts.


c.
A301940
0.375,0.604 0.688,0.802 0.313,0.198 10 false 17 0.375,2.521 0.688,2.719 0.313,0.198 10 false (A) 0.74,0.5 1.052,0.698 0.313,0.198 10 false 11 0.729,0.667 1.042,0.865 0.313,0.198 10 false (B) 1.094,0.563 1.406,0.76 0.313,0.198 10 false 9 1.042,0.719 1.354,0.917 0.313,0.198 10 false (A) 1.448,0.5 1.76,0.698 0.313,0.198 10 false 3 1.406,0.646 1.719,0.844 0.313,0.198 10 false (B) 1.75,0.552 2.063,0.75 0.313,0.198 10 false 1 1.708,0.688 2.021,0.885 0.313,0.198 10 false (A) 2.135,0.51 2.448,0.708 0.313,0.198 10 false 6 2.094,0.656 2.406,0.854 0.313,0.198 10 false (B) 2.458,0.542 2.771,0.74 0.313,0.198 10 false 8 2.417,0.677 2.729,0.875 0.313,0.198 10 false (A) 2.781,0.5 3.094,0.698 0.313,0.198 10 false 14 2.781,0.646 3.094,0.844 0.313,0.198 10 false (B) 3.115,0.531 3.427,0.729 0.313,0.198 10 false 16 3.104,0.698 3.417,0.896 0.313,0.198 10 false (A) 0.385,2.385 0.698,2.583 0.313,0.198 10 false 15 0.365,0.76 0.677,0.958 0.313,0.198 10 false (A) 0.708,2.51 1.021,2.708 0.313,0.198 10 false 13 0.698,2.667 1.01,2.865 0.313,0.198 10 false (B) 1.083,2.385 1.281,2.583 0.198,0.198 10 false 7 1.406,2.521 1.604,2.719 0.198,0.198 10 false 5 1.771,2.365 1.969,2.563 0.198,0.198 10 false 2 2.104,2.51 2.302,2.708 0.198,0.198 10 false 4 2.417,2.375 2.615,2.573 0.198,0.198 10 false 10 2.75,2.51 2.948,2.708 0.198,0.198 10 false 12 3.094,2.375 3.292,2.573 0.198,0.198 10 false 18 1.031,2.542 1.344,2.74 0.313,0.198 10 false (A) 1.719,2.521 2.031,2.719 0.313,0.198 10 false (A) 2.417,2.521 2.729,2.719 0.313,0.198 10 false (A) 3.094,2.521 3.406,2.719 0.313,0.198 10 false (A) 1.365,2.688 1.677,2.885 0.313,0.198 10 false (B) 2.063,2.677 2.375,2.875 0.313,0.198 10 false (B) 2.74,2.667 3.052,2.865 0.313,0.198 10 false (B)

Install the 18 cylinder head bolts and 18 washers and uniformly tighten the bolts in several passes in the sequence shown in the illustration.

Torque:
85 N*m (867 kgf*cm, 63 ft.*lbf)

Standard Bolt Length
Item Specified Condition
A 110 mm (4.33 in.)
B 167 mm (6.57 in.)

If any of the cylinder head bolts does not meet the torque specification, replace it.


d.
A060141
0.781,0.708 0.781,1.375 true 0.25,1.01 0.438,1.177 0.188,0.167 10 false *a 1.156,0.969 1.469,1.156 0.313,0.188 10 false 90° 1.802,0.531 2.115,0.719 0.313,0.188 10 false 90° 0.813,0.073 1.125,0.26 0.313,0.188 10 false 90° 0.052,0.479 0.365,0.667 0.313,0.188 10 false 90° 0.688,1.406 0.854,1.573 0.167,0.167 10 false *1
*1 Paint Mark
*a Front


Mark the front of each cylinder head bolt with paint.


e.

Further tighten the cylinder head bolts by 90° in the sequence shown in the illustration above.


f.

Finally, tighten the cylinder head bolts by an additional 90°.


g.

Check that the paint marks are now facing rearward.


Hide 5.INSTALL CYLINDER BLOCK INSULATOR (w/ EGR Cooler)

a.

Install the cylinder block insulator to the cylinder head.


Hide 6.INSTALL NO. 2 TIMING BELT COVER

a.
A301941
0.594,2.698 0.594,2.333 true 1.625,2.063 1.625,1.698 false 2.406,2.865 2.188,2.865 true 0.51,2.74 0.823,2.938 0.313,0.198 10 false *1 1.531,2.083 1.844,2.281 0.313,0.198 10 false *1 2.448,2.76 2.76,2.958 0.313,0.198 10 false *1
*1 Seal Packing


Apply seal packing (FIPG) to the specified areas shown in the illustration.

Seal packing:

Toyota Genuine Seal Packing Black, Three Bond 1207B or equivalent


NOTICE:

After applying FIPG, install the No. 2 timing belt cover within 3 minutes and tighten its bolts and nut within 15 minutes.



b.

Clean the bolts and their holes.


c.

Apply adhesive to 2 or 3 threads at the end of each of the 4 bolts.

Adhesive:

Toyota Genuine Adhesive 1324, Three Bond 1324 or equivalent



d.

Install the No. 2 timing belt cover with the 4 bolts and nut.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)


Hide 7.INSTALL CAMSHAFT TIMING PULLEY

a.
A060182

Install the camshaft timing pulley.


b.

Tighten the bolt of the camshaft timing pulley while holding the camshaft with a wrench.

Torque:
98 N*m (1000 kgf*cm, 72 ft.*lbf)


Hide 10.INSTALL NO. 1 COMPRESSOR MOUNTING BRACKET (w/ Air Conditioning System)

Hide 11.CONNECT COOLER COMPRESSOR ASSEMBLY (w/ Air Conditioning System)

Hide 19.CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).