Home › Engine / Hybrid System › 2KD-FTV ENGINE MECHANICAL › ENGINE ASSEMBLY(w/ DPF) › from 2012.10
RM1840EF _51 Engine / Hybrid System _009574 2KD-FTV ENGINE MECHANICAL _0052179 ENGINE ASSEMBLY(w/ DPF) A

2KD-FTV ENGINE MECHANICAL  ENGINE ASSEMBLY(w/ DPF)  REMOVAL  


CAUTION / NOTICE / HINT

NOTICE:
·

When replacing the injectors (including shuffling the injectors between the cylinders), common rail or cylinder head, it is necessary to replace the injection pipes with new ones.

·

When replacing the fuel supply pump, common rail, cylinder block, cylinder head, cylinder head gasket or timing gear case, it is necessary to replace the fuel inlet pipe with a new one.

·

After removing the injection pipes, clean them with a brush and compressed air.



PROCEDURE

Hide 1. PRECAUTION

NOTICE:

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).


Hide 2.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).


Hide 3.REMOVE HOOD SUB-ASSEMBLY

a.

Disconnect the washer nozzle hose.


b.

Remove the 4 bolts and hood.


Hide 4.REMOVE NO. 1 ENGINE UNDER COVER

Hide 5.REMOVE NO. 2 ENGINE UNDER COVER

Hide 9.DRAIN POWER STEERING FLUID

Hide 10.REMOVE BATTERY CLAMP SUB-ASSEMBLY

a.

Remove the bolt, nut and battery clamp.


Hide 11.REMOVE BATTERY

Hide 12.REMOVE BATTERY TRAY

Hide 14.REMOVE INTERCOOLER ASSEMBLY WITH INTAKE AIR CONNECTOR

Hide 15.REMOVE RADIATOR ASSEMBLY

Hide 17.REMOVE FRONT EXHAUST PIPE ASSEMBLY

Hide 19.REMOVE PROPELLER WITH CENTER BEARING SHAFT ASSEMBLY

Hide 20.DISCONNECT HEATER HOSE

a.
A236415

Disconnect the 2 heater hoses.


Hide 21.DISCONNECT PRESSURE FEED TUBE ASSEMBLY

a.
A236416

Disconnect the oil reservoir to pump hose.


b.
A236417

Disconnect the pressure feed tube.


Hide 22.DISCONNECT FUEL HOSE

a.
A236418

Disconnect the 2 fuel hoses.


Hide 23.DISCONNECT UNION TO CONNECTOR TUBE HOSE

a.
A236419

Disconnect the union to connector tube hose.


Hide 25.DISCONNECT WIRE HARNESS

A302600

a.

Remove the upper relay block cover.


b.

Remove the side relay block cover.


c.

Remove the nut and disconnect the engine room junction block wire.


d.

Disconnect the 2 engine room junction block connectors.


e.

Remove the bolt and disconnect the ground cable.


f.
A233020

Remove the 2 nuts, detach the clamp and disconnect the wire harness.


g.

Disconnect the 4 glow plug controller connectors.


h.

Disconnect the 4 injector driver connectors.


i.
A272541

Disconnect the 4WD control ECU connector.


j.

Disconnect the 6 ECM connectors.


Hide 26.DISCONNECT COOLER COMPRESSOR ASSEMBLY (w/ Air Conditioning System)

a.

Remove the 4 bolts and disconnect the cooler compressor.

HINT:

It is not necessary to completely remove the cooler compressor. With the hoses connected to the cooler compressor, hang the cooler compressor on the vehicle body with a rope.



Hide 28.REMOVE REAR NO. 1 ENGINE MOUNTING INSULATOR

HINT:

Perform this procedure only when replacement of the rear No. 1 engine mounting insulator is necessary.


a.

Remove the 4 bolts and rear No. 1 engine mounting insulator.


Hide 29.REMOVE CLUTCH COVER ASSEMBLY

Hide 30.REMOVE CLUTCH DISC ASSEMBLY

Hide 31.REMOVE FLYWHEEL SUB-ASSEMBLY

a.
A072851
1.865,0.542 2.438,0.49 2.438,0.49 2.052,0.875 true 2.51,0.396 2.844,0.563 0.333,0.167 10 false SST

Using SST, hold the crankshaft pulley.

SST
09213-58014  
09330-00021  


b.
A114803

Remove the 8 bolts and flywheel.


Hide 32.REMOVE REAR END PLATE

a.

Remove the bolt and rear end plate.


Hide 33.INSTALL ENGINE HANGERS

a.
A224109
0.854,0.958 1.135,0.573 1.135,0.573 1.26,0.573 true 2.75,0.948 2.938,0.698 2.938,0.698 3.146,0.698 true 1.344,0.469 1.625,0.708 0.281,0.24 10 true *1 3.177,0.604 3.417,0.813 0.24,0.208 10 true *2
*1 No. 1 Engine Hanger
*2 No. 2 Engine Hanger


Install a No. 1 engine hanger and No. 2 engine hanger with 2 bolts as shown in the illustration.

Torque:
for No. 1 engine hanger : 25 N*m (255 kgf*cm, 18 ft.*lbf)
for No. 2 engine hanger : 68 N*m (693 kgf*cm, 50 ft.*lbf)

HINT:

Part No.

No. 1 Engine Hanger 12284-30020
No. 2 Engine Hanger 12282-67030
Bolt 91552-81014 and 91642-81030


NOTICE:

Install the engine hangers with new bolts.



Hide 34.REMOVE ENGINE ASSEMBLY

a.

Attach an engine sling device and hang the engine with a chain block.


b.
A098988

Remove the 4 bolts and 4 nuts.


c.

Remove the engine by operating the engine sling device and chain block.


Hide 35.INSTALL ENGINE TO ENGINE STAND

a.

Install the engine to an engine stand with bolts.


b.

Remove the 2 bolts and 2 engine hangers.


Hide 36.REMOVE ENGINE WIRE

a.

Remove the engine wire from the engine.


Hide 37.REMOVE FRONT ENGINE MOUNTING INSULATOR

a.
A233592
0.073,0.052 0.354,0.302 0.281,0.25 10 true *A 1.729,0.042 2,0.323 0.271,0.281 10 true *B
*A RH Side
*B LH Side


Remove the 2 nuts and 2 front engine mounting insulators.