1.INSTALL ENGINE HANGER
2.REMOVE ENGINE ASSEMBLY FROM ENGINE STAND
Pay attention to the angle of the sling device as the engine assembly or engine hangers may be damaged or deformed if the angle is incorrect.
With the exception of installing the engine assembly to an engine stand or removing the engine assembly from an engine stand, do not perform any work on the engine while it is suspended, as doing so is dangerous.
Attach the engine sling device and hang the engine assembly with the chain block.
Remove the engine assembly from the engine stand.
3.INSTALL ENGINE ASSEMBLY
Perform "Inspection After Repair" after replacing the engine assembly.
Click hereEngine / Hybrid System>1GR-FE ENGINE CONTROL>SFI SYSTEM>INITIALIZATION
Slowly lower the engine assembly into the engine compartment.
Install the engine assembly to the body with the 4 bolts and 4 nuts.
| *a | Front Engine Mounting Insulator
(LH Side) |
| *b | Claw (Stopper) |
|
Front |
Make sure to tighten the side with the nut.
When installing a bolt with a claw (stopper), make sure to install the bolt with the claw (stopper) as shown in the illustration so that a clearance is maintained between the claw (stopper) and the intermediate shaft.
Remove the 4 bolts, No. 1 engine hanger and No. 2 engine hanger.
32101
4.INSTALL DRIVE PLATE AND RING GEAR SUB-ASSEMBLY
35000
5.INSTALL AUTOMATIC TRANSMISSION ASSEMBLY
6.INSTALL DRIVE PLATE AND TORQUE CONVERTER ASSEMBLY SETTING BOLT
37100
7.INSTALL PROPELLER SHAFT WITH CENTER BEARING ASSEMBLY (for 2WD and Pre-Runner)
37100
8.INSTALL PROPELLER SHAFT WITH CENTER BEARING ASSEMBLY (for 4WD)
51569
9.INSTALL PROPELLER SHAFT GUARD
41110F
10.INSTALL FRONT DIFFERENTIAL CARRIER ASSEMBLY (for 4WD)
11.INSTALL POWER STEERING LINK ASSEMBLY (for 4WD)
45219
12.CONNECT STEERING SLIDING YOKE (for 4WD)
43410D
13.INSTALL FRONT DRIVE SHAFT HOLE SNAP RING (for 4WD)
43420
14.INSTALL FRONT DRIVE SHAFT ASSEMBLY LH (for 4WD)
43410
15.INSTALL FRONT DRIVE SHAFT ASSEMBLY RH (for 4WD)
Use the same procedure described for the LH side.
48069
16.CONNECT FRONT LOWER NO. 1 SUSPENSION ARM SUB-ASSEMBLY LH (for 4WD)
17.CONNECT TIE ROD END SUB-ASSEMBLY LH (for 4WD)
89543
18.CONNECT FRONT SPEED SENSOR LH (for 4WD)
43502H
19.INSTALL FRONT AXLE SHAFT NUT (for 4WD)
43514C
20.INSTALL FRONT AXLE HUB GREASE CAP (for 4WD)
37140
21.INSTALL FRONT PROPELLER SHAFT ASSEMBLY (for 4WD)
51561D
22.INSTALL PROPELLER SHAFT GUARD (for 4WD)
23802B
23.CONNECT NO. 2 FUEL PIPE SUB-ASSEMBLY
Connect the No. 2 fuel pipe sub-assembly, and slide the clamp to secure the hose.
23801P
24.CONNECT NO. 1 FUEL PIPE SUB-ASSEMBLY
25.INSTALL WATER HOSE SUB-ASSEMBLY
Install the water hose sub-assembly, and slide the 4 clamps to secure the hose.
Install the bolt.
88320
26.CONNECT COOLER COMPRESSOR ASSEMBLY
27020
27.INSTALL GENERATOR ASSEMBLY
for 115A Type:
Click herePower Source / Network>1GR-FE BATTERY / CHARGING>GENERATOR(for 115A Type)>INSTALLATION
for 100A Type:
Click herePower Source / Network>1GR-FE BATTERY / CHARGING>GENERATOR(for 100A Type)>INSTALLATION
82121
28.CONNECT ENGINE WIRE
Connect the 2 connectors to the engine room relay block.
Connect the engine wire to the engine room relay block with the nut.
Attach the 2 claws and install the No. 1 relay block cover side to the engine room relay block.
Attach the 3 claws and install the No. 1 relay block cover upper to the engine room relay block.
Attach the 2 clamps and connect the No. 2 engine wire with the 2 bolts.
Install the battery tray.
Install the battery.
Install the battery hold down clamp with the 2 nuts.
Tighten the nut and install the positive (+) battery terminal.
Position the positive (+) battery terminal as shown in the illustration.
Connect the engine room main wire to the battery positive cable with the nut.
Push the engine wire through the dash panel into the cabin.
The wire should be within the range shown in the illustration.
Connect the engine wire and attach the clamp to the bracket.
Connect the engine wire with the bolt.
Connect the connector.
Attach the 2 clamps and connect the 3 connectors to the instrument panel wire.
89661
29.INSTALL ECM
55550
30.INSTALL GLOVE COMPARTMENT DOOR ASSEMBLY
55607
31.INSTALL NO. 2 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY (w/ Cover)
11363A
32.INSTALL FLYWHEEL HOUSING SIDE COVER
28100
33.INSTALL STARTER ASSEMBLY
17105
34.INSTALL EXHAUST MANIFOLD SUB-ASSEMBLY LH
17119
35.INSTALL NO. 2 MANIFOLD STAY
17104
36.INSTALL EXHAUST MANIFOLD SUB-ASSEMBLY RH
17118
37.INSTALL MANIFOLD STAY
17410
38.INSTALL FRONT EXHAUST PIPE ASSEMBLY
17450B
39.INSTALL FRONT NO. 2 EXHAUST PIPE ASSEMBLY
17129
40.INSTALL INTAKE AIR SURGE TANK
44320
41.CONNECT VANE PUMP ASSEMBLY
Connect the vane pump assembly with the 2 bolts.
Do not hit other parts with the pulley when installing the vane pump.
Connect the connector.
16400
42.INSTALL RADIATOR ASSEMBLY
32941
43.CONNECT NO. 1 OIL COOLER INLET HOSE
32942
44.CONNECT NO. 1 OIL COOLER OUTLET HOSE
16711
45.INSTALL FAN SHROUD
16470
46.INSTALL RADIATOR RESERVOIR
16571
47.INSTALL RADIATOR HOSE INLET
16572
48.INSTALL RADIATOR HOSE OUTLET
16593
49.INSTALL NO. 1 RADIATOR AIR GUIDE
17700
50.INSTALL AIR CLEANER CASE SUB-ASSEMBLY
Install the air cleaner case sub-assembly with the 3 bolts.
Connect the 3 clamps to the air cleaner case sub-assembly.
17801
51.INSTALL AIR CLEANER FILTER ELEMENT SUB-ASSEMBLY
17705
52.INSTALL AIR CLEANER CAP SUB-ASSEMBLY WITH NO. 1 AIR CLEANER HOSE
53294C
53.INSTALL RADIATOR SIDE DEFLECTOR LH
53293C
54.INSTALL RADIATOR SIDE DEFLECTOR RH
Use the same procedure described for the LH side.
53735B
55.INSTALL FRONT UPPER FENDER APRON SEAL LH
Install the front upper fender apron seal LH with 6 new clips.
53735B
56.INSTALL FRONT UPPER FENDER APRON SEAL RH
Install the front upper fender apron seal RH with 6 new clips.
53882F
57.INSTALL FRONT FENDER SEAL LH
for 2WD:
Install the front fender seal LH with 5 new clips.
for 4WD and Pre-Runner:
Install the front fender seal LH with 6 new clips.
53882F
58.INSTALL FRONT FENDER SEAL RH
for 2WD:
Install the front fender seal RH with 5 new clips.
for 4WD and Pre-Runner:
Install the front fender seal RH with 6 new clips.
59.ADD DIFFERENTIAL OIL (for 4WD)
51407A
60.INSTALL NO. 3 ENGINE UNDER COVER SUB-ASSEMBLY (for 4WD and Pre-Runner)
51442
61.INSTALL NO. 2 ENGINE UNDER COVER (for 4WD and Pre-Runner)
51410
62.INSTALL NO. 1 ENGINE UNDER COVER ASSEMBLY (for 4WD and Pre-Runner)
53301
63.INSTALL HOOD SUB-ASSEMBLY
Install the hood sub-assembly to the 2 hood hinge assemblies with the 4 bolts.
Connect the washer nozzle hose.
Adjust the hood sub-assembly.
64.CONNECT CABLE TO NEGATIVE BATTERY TERMINAL
When disconnecting the cable, some systems need to be initialized after the cable is reconnected.
Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION
65.ADD ENGINE OIL
66.ADD ENGINE COOLANT
67.INSPECT FOR COOLANT LEAK
68.INSPECT FOR FUEL LEAK
69.INSPECT FOR OIL LEAK
70.INSPECT FOR EXHAUST GAS LEAK
71.INSPECT IGNITION TIMING
72.INSPECT ENGINE IDLE SPEED
73.INSPECT CO/HC