The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed, installed, or replaced during the engine assembly removal/installation are shown below.
To prevent injury due to contact with an operating fan and generator V-belt or cooling fan, keep your hands and clothing away from the fan and generator V-belt and cooling fans when working in the engine compartment with the engine running.
Do not remove the radiator cap sub-assembly, cylinder block drain cock plugs or radiator drain cock plug while the engine and radiator assembly are still hot. Pressurized, hot engine coolant and steam may be released and cause serious burns.
To prevent burns, do not touch the engine, exhaust manifold or other high temperature components while the engine is hot.
To prevent burns, do not touch the engine, exhaust pipe or other high temperature components while the engine is hot.
1.PLACE FRONT WHEELS FACING STRAIGHT AHEAD (for 4WD)
2.DISCHARGE FUEL SYSTEM PRESSURE
3. PRECAUTION
After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work.
Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION
4.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL
When disconnecting the cable, some systems need to be initialized after the cable is reconnected.
Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION
5.DRAIN ENGINE COOLANT
6.DRAIN ENGINE OIL
7.DRAIN MANUAL TRANSMISSION OIL
for R151F:
Click hereDrivetrain>R151F MANUAL TRANSMISSION / TRANSAXLE>MANUAL TRANSMISSION OIL>REPLACEMENT
8.DRAIN DIFFERENTIAL OIL (for 4WD)
53301
9.REMOVE HOOD SUB-ASSEMBLY
Disconnect the washer nozzle hose from the hood sub-assembly.
Remove the 4 bolts and hood sub-assembly from the 2 hood hinge assemblies.
17705
10.REMOVE AIR CLEANER CAP SUB-ASSEMBLY WITH NO. 1 AIR CLEANER HOSE
Disconnect the intake mass air flow meter connector and detach the 2 wire harness clamps.
Detach the 4 clamps.
Loosen the hose clamp and remove the air cleaner cap sub-assembly with No. 1 air cleaner hose.
17801
11.REMOVE AIR CLEANER FILTER ELEMENT SUB-ASSEMBLY
Remove the air cleaner filter element sub-assembly from the air cleaner case sub-assembly.
17701
12.REMOVE AIR CLEANER CASE SUB-ASSEMBLY
Detach the 3 wire harness clamps.
Remove the 3 bolts and air cleaner case sub-assembly.
17861
13.REMOVE INTAKE AIR CONNECTOR
51410
14.REMOVE NO. 1 ENGINE UNDER COVER ASSEMBLY (for 4WD and Pre-Runner)
51442
15.REMOVE NO. 2 ENGINE UNDER COVER (for 4WD and Pre-Runner)
51407A
16.REMOVE NO. 3 ENGINE UNDER COVER SUB-ASSEMBLY (for 4WD and Pre-Runner)
53737B
17.REMOVE FRONT UPPER FENDER APRON SEAL LH
Remove the 6 clips and front upper fender apron seal LH.
53736
18.REMOVE FRONT UPPER FENDER APRON SEAL RH
w/ Secondary Air Injection System:
for Pre-Runner:
Remove the 5 clips and front upper fender apron seal RH.
w/o Secondary Air Injection System:
for 2WD:
Remove the 6 clips and front upper fender apron seal RH.
for 4WD and Pre-Runner:
Remove the 6 clips and front upper fender apron seal RH.
53882F
19.REMOVE FRONT FENDER SEAL LH
for 2WD:
Remove the 5 clips and front fender seal LH.
for 4WD and Pre-Runner:
Remove the 6 clips and front fender seal LH.
53882F
20.REMOVE FRONT FENDER SEAL RH
for 2WD:
Remove the 5 clips and front fender seal RH.
for 4WD and Pre-Runner:
Remove the 6 clips and front fender seal RH.
53294C
21.REMOVE RADIATOR SIDE DEFLECTOR LH
53293C
22.REMOVE RADIATOR SIDE DEFLECTOR RH
Use the same procedure described for the LH side.
16593
23.REMOVE NO. 1 RADIATOR AIR GUIDE
16571
24.REMOVE RADIATOR HOSE INLET
16572
25.REMOVE RADIATOR HOSE OUTLET
17621A
26.DISCONNECT AIR PUMP INLET (w/ Secondary Air Injection System)
16470
27.REMOVE RADIATOR RESERVOIR
Click here
Click hereEngine / Hybrid System>2TR-FE COOLING>RADIATOR>REMOVAL
16711
28.REMOVE FAN SHROUD
16400
29.REMOVE RADIATOR ASSEMBLY
30.DISCONNECT HEATER HOSE
| *1 | Heater Water Outlet Hose |
| *2 | Heater Water Inlet Hose |
Slide the clamp and disconnect the heater water outlet hose from the heater radiator unit sub-assembly.
Slide the clamp and disconnect the heater water inlet hose from the heater radiator unit sub-assembly.
44320
31.DISCONNECT VANE PUMP ASSEMBLY
Disconnect the power steering oil pressure switch connector.
Remove the 2 bolts and disconnect the vane pump assembly.
Do not hit other parts with the pulley when disconnecting the vane pump assembly.
Be sure to suspend the vane pump assembly securely.
15301
32.REMOVE ENGINE OIL LEVEL DIPSTICK
11452
33.REMOVE ENGINE OIL LEVEL DIPSTICK GUIDE
Remove the bolt, engine oil level dipstick guide and O-ring.
Cover the engine oil level dipstick guide hole to prevent foreign matter from entering it.
88320
34.DISCONNECT COOLER COMPRESSOR ASSEMBLY (w/ Air Conditioning System)
28100
35.REMOVE STARTER ASSEMBLY
36.DISCONNECT PURGE LINE HOSE
Slide the clamp and disconnect the purge line hose from the purge VSV.
44774
37.DISCONNECT UNION TO CONNECTOR TUBE HOSE
Slide the clamp and disconnect the union to connector tube hose from the intake manifold.
17344
38.DISCONNECT NO. 4 AIR INJECTION SYSTEM HOSE (w/ Secondary Air Injection System)
23273C
39.DISCONNECT NO. 2 FUEL HOSE
23271H
40.DISCONNECT NO. 1 FUEL HOSE
55550
41.REMOVE GLOVE COMPARTMENT DOOR ASSEMBLY
89661
42.REMOVE ECM
43.DISCONNECT ENGINE WIRE
Detach the 2 clamps and disconnect the 3 connectors from the instrument panel wire.
w/ Secondary Air Injection System:
Disconnect the air injection control driver connector.
Detach the clamp.
Remove the bolt and disconnect the engine wire from the air injection control bracket.
w/o Secondary Air Injection System:
Remove the bolt and disconnect the engine wire from the air injection control bracket.
Detach the grommet and pull out the engine wire from the cabin.
Disconnect the connector from the engine room main wire.
Remove the nut and disconnect the engine room main wire from the positive (+) battery terminal.
Loosen the nut and remove the positive (+) battery terminal.
Loosen the 2 nuts and remove the battery hold down clamp.
Remove the battery.
Remove the battery tray.
Detach the 2 clamps and remove the 2 bolts and disconnect the No. 2 engine wire.
Detach the clamp and remove the bolt and No. 2 engine wire.
Detach the 3 claws and remove the No. 1 relay block cover upper from the engine room relay block.
Detach the 2 claws and remove the No. 1 relay block cover side from the engine room relay block.
Remove the nut and disconnect the engine wire from the engine room relay block.
Disconnect the 2 connectors from the engine room relay block.
Detach the clamp.
Remove the bolt and disconnect the wire clamp from the front engine mounting bracket LH.
Disconnect the air fuel ratio sensor connector.
Remove the bolt and disconnect the sensor bracket from the right side of the frame.
17410
44.REMOVE FRONT EXHAUST PIPE ASSEMBLY
51561D
45.REMOVE PROPELLER SHAFT GUARD (for 4WD)
37140
46.REMOVE FRONT PROPELLER SHAFT ASSEMBLY (for 4WD)
51569
47.REMOVE PROPELLER SHAFT GUARD
37100
48.REMOVE PROPELLER SHAFT WITH CENTER BEARING ASSEMBLY (for 2WD and Pre-Runner)
37100
49.REMOVE PROPELLER SHAFT WITH CENTER BEARING ASSEMBLY (for 4WD)
43514C
50.REMOVE FRONT AXLE HUB GREASE CAP LH (for 4WD)
43502H
51.REMOVE FRONT AXLE SHAFT NUT LH (for 4WD)
89543
52.DISCONNECT FRONT SPEED SENSOR LH (for 4WD)
53.DISCONNECT TIE ROD END SUB-ASSEMBLY LH (for 4WD)
48069
54.DISCONNECT FRONT LOWER NO. 1 SUSPENSION ARM ASSEMBLY LH (for 4WD)
43420
55.REMOVE FRONT DRIVE SHAFT ASSEMBLY LH (for 4WD)
43410
56.REMOVE FRONT DRIVE SHAFT ASSEMBLY RH (for 4WD)
Use the same procedure described for the LH side.
43410D
57.REMOVE FRONT DRIVE SHAFT HOLE SNAP RING (for 4WD)
58.SECURE STEERING WHEEL ASSEMBLY (for 4WD)
45219
59.DISCONNECT STEERING SLIDING YOKE (for 4WD)
44250
60.REMOVE POWER STEERING LINK ASSEMBLY (for 4WD)
41110F
61.REMOVE FRONT DIFFERENTIAL CARRIER ASSEMBLY (for 4WD)
33030
62.REMOVE MANUAL TRANSMISSION UNIT ASSEMBLY
31210
63.REMOVE CLUTCH COVER ASSEMBLY
31250
64.REMOVE CLUTCH DISC ASSEMBLY
13405
65.REMOVE FLYWHEEL SUB-ASSEMBLY
11355
66.REMOVE REAR END PLATE
Remove the bolt and disconnect the No. 1 water by-pass pipe from the rear end plate.
Remove the bolt and rear end plate from the cylinder block sub-assembly.
67.INSTALL ENGINE HANGER
| *a | Rear Side |
| *b | Front Side |
Install the 2 engine hangers with the 2 bolts as shown in the illustration.
| No. 1 Engine Hanger | 12281-0C010
12281-0C030 |
| Bolt | 90119-T0388
91672-81025 |
68.REMOVE ENGINE ASSEMBLY
Attach an engine sling device and hang the engine assembly with a chain block.
Remove the 4 bolts and 4 nuts from the body.
Remove the engine assembly by operating the engine sling device and chain block.
Make sure that the engine is clear of all wiring and hoses.
While lowering the engine from the vehicle, do not allow it to contact the vehicle.
69.INSTALL ENGINE ASSEMBLY TO ENGINE STAND
Install the engine to an engine stand with bolts.
Pay attention to the angle of the sling device as the engine assembly or engine hangers may be damaged or deformed if the angle is incorrect.
With the exception of installing the engine assembly to an engine stand or removing the engine assembly from an engine stand, do not perform any work on the engine while it is suspended, as doing so is dangerous.
Remove the 2 bolts and 2 engine hangers.
82121
70.REMOVE ENGINE WIRE
Remove the engine wire from the engine assembly.
12391
71.REMOVE FRONT ENGINE MOUNTING HEAT INSULATOR RH
Remove the bolt and front engine mounting heat insulator RH from the front engine mounting insulator.
12361
72.REMOVE FRONT ENGINE MOUNTING INSULATOR
Perform this procedure only when replacement of the front engine mounting insulator is necessary.
| *a | LH Side |
| *b | RH Side |
Remove the 2 nuts and 2 front engine mounting insulators from the 2 front engine mounting brackets.